400 MSPS 14-Bit, 1.8 V CMOS

Direct Digital Synthesizer

AD9954

Rev. 0

Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700

www.analog.com

Fax: 781.326.8703

FEATURES

400 MSPS internal clock speed
Integrated 14-bit DAC
Programmable phase/amplitude dithering
32-bit tuning word
Phase noise 120 dBc/Hz @ 1 kHz offset (DAC output)
Excellent dynamic performance

>80 dB SFDR @ 160 MHz (±100 kHz offset) A

OUT

Serial I/O control
Ultrahigh speed analog comparator
Automatic linear and nonlinear frequency sweeping

capability

4 frequency/phase offset profiles
1.8 V power supply
Software and hardware controlled power-down
48-lead TQFP/EP package
Integrated 1024 word Ч 32-bit RAM

Support for 5 V input levels on most digital inputs
PLL REFCLK multiplier (4Ч to 20Ч)
Internal oscillator, can be driven by a single crystal
Phase modulation capability
Multichip synchronization

APPLICATIONS

Agile LO frequency synthesis
Programmable clock generator
FM chirp source for radar and scanning systems
Automotive radar
Test and measurement equipment
Acousto-optic device drivers

FUNCTIONAL BLOCK DIAGRAM

FREQUENCY

ACCUMULATOR

STATIC RAM

1024

COS(X)

CONTROL REGISTERS

OSCILLATOR/BUFFER

COMPARATOR

SYNC

ENABLE

I/O UPDATE

DAC_R

SET

DDS CORE

PHASE

OFFSET

PHASE

ACCUMULATOR

IOUT
IOUT

OSK
PWRDWNCTL

COMP_OUT

COMP_IN
COMP_IN

REFCLK

CRYSTAL OUT

I/O PORT

PS<1:0>

RAM DATA

<31:18>

DDS

CLOCK

RAM

DATA

LTA FRE

NCY

TUNING WORD

FRE

NCY

TUNING WORD

RAM DATA

DDS

CLOCK

LTA FRE

NCY

RAMP

RATE

ACUMULATOR

ESET

DAC

MUX

SYSTEM

CLOCK

SYSTEM

CLOCK

SYNC_IN

SYNC_CLK

RESET

TIMING AND CONTROL LOGIC

20

CLOCK

MULTIPLIER

ч 4

AD9954

RAM CONTROL

03374-0-001

Figure 1. 48-LeadTQFP/EP

AD9954

Rev. 0 | Page 2 of 36

TABLE OF CONTENTS

General Description ......................................................................... 3

AD9954--Electrical Specifications ................................................ 4

Absolute Maximum Ratings............................................................ 7

Pin Configurations ........................................................................... 8

Pin Function Descriptions .............................................................. 9

Typical Performance Characteristics ........................................... 10

Theory of Operation ...................................................................... 13

Component Blocks ..................................................................... 13

Modes of Operation ................................................................... 22

Serial Port Operation ................................................................. 30

Instruction Byte .......................................................................... 32

Serial Interface Port Pin Description....................................... 32

MSB/LSB Transfers .................................................................... 32

RAM I/O Via Serial Port ........................................................... 32

Suggested Application Circuits..................................................... 35

Outline Dimensions ....................................................................... 36

ESD Caution................................................................................ 36

Ordering Guide .......................................................................... 36

REVISION HISTORY

Revision 0: Initial Version

AD9954

Rev. 0 | Page 4 of 36

AD9954--ELECTRICAL SPECIFICATIONS

Table 1. Unless otherwise noted, AVDD,

DVDD = 1.8 V ± 5%, DVDD_I/O = 3.3 V ± 5%, R

SET

= 3.92 k, External Reference Clock

Frequency = 20 MHz with REFCLK Multiplier Enabled at 20Ч. DAC Output Must Be Referenced to AVDD, Not AGND.

Parameter

Temp

Test
Level

Min

Typ

Max

Unit

REF CLOCK INPUT CHARACTERISTICS

Frequency Range

REFCLK Multiplier Disabled

FULL

400

MHz

REFCLK Multiplier Enabled at 4Ч

FULL

100

MHz

REFCLK Multiplier Enabled at 20Ч

FULL

MHz

Input Capacitance

25°C

Input Impedance

25°C

1.5

Duty Cycle

25°C

Duty Cycle with REFCLK Multiplier Enabled

25°C

REFCLK Input Power

FULL IV

dBm

DAC OUTPUT CHARACTERISTICS

Resolution

Bits

Full Scale Output Current

25°C

Gain Error

25°C

+10

%FS

Output Offset

25°C

0.6

µA

Differential Nonlinearity

25°C

LSB

Integral Nonlinearity

25°C

LSB

Output Capacitance

25°C

Residual Phase Noise @ 1 kHz Offset, 40 MHz A

OUT

REFCLK Multiplier Enabled @ 20Ч

25°C

105

dBc/Hz

REFCLK Multiplier Enabled @ 4Ч

25°C

115

dBc/Hz

REFCLK Multiplier Disabled

25°C

132

dBc/Hz

Voltage Compliance Range

25°C

AVDD 0.5

AVDD + 0.5

Wideband SFDR

1 MHz to 10 MHz Analog Out

25°C

dBc

10 MHz to 40 MHz Analog Out

25°C

dBc

40 MHz to 80 MHz Analog Out

25°C

dBc

80 MHz to 120 MHz Analog Out

25°C

dBc

120 MHz to 160 MHz Analog Out

25°C

dBc

Narrow Band SFDR

40 MHz Analog Out (±1 MHz)

25°C

dBc

40 MHz Analog Out (±250 kHz)

25°C

dBc

40 MHz Analog Out (±50 kHz)

25°C

dBc

40 MHz Analog Out (±10 kHz)

25°C

dBc

80 MHz Analog Out (±1 MHz)

25°C

dBc

80 MHz Analog Out (±250 kHz)

25°C

dBc

80 MHz Analog Out (±50 kHz)

25°C

dBc

80 MHz Analog Out (±10 kHz)

25°C

dBc

120 MHz Analog Out (±1 MHz)

25°C

dBc

120 MHz Analog Out (±250 kHz)

25°C

dBc

120 MHz Analog Out (±50 kHz)

25°C

dBc

120 MHz Analog Out (±10 kHz)

25°C

dBc

160 MHz Analog Out (±1 MHz)

25°C

dBc

160 MHz Analog Out (±250 kHz)

25°C

dBc

160 MHz Analog Out (±50 kHz)

25°C

dBc

160 MHz Analog Out (±10 kHz)

25°C

dBc

AD9954

Rev. 0 | Page 5 of 36

Parameter

Temp

Test
Level

Min

Typ

Max

Unit

COMPARATOR INPUT CHARACTERISTICS

Input Capacitance

25°C

Input Resistance

25°C

500

Input Current

25°C

±12

µA

Hysteresis 25°C

COMPARATOR OUTPUT CHARACTERISTICS

Logic 1 Voltage, High Z Load

FULL

1.6

Logic 0 Voltage, High Z Load

FULL

0.4

Propagation Delay

25°C

Output Duty Cycle Error

25°C

±5

Rise/Fall Time, 5 pF Load

25°C

Toggle Rate, High Z Load

25°C

200

MHz

Output Jitter

25°C IV

RMS

COMPARATOR NARROWBAND SFDR

dBc

10 MHz (1 MHz)

25°C

dBc

10 MHz (250 kHz)

25°C

dBc

10 MHz (50 kHz)

25°C

dBc

10 MHz (10 kHz)

25°C

dBc

70 MHz (1 MHz)

25°C

dBc

70 MHz (250 kHz)

25°C

dBc

70 MHz (50 kHz)

25°C

dBc

70 MHz (10 kHz)

25°C

dBc

110 MHz (1 MHz)

25°C

dBc

110 MHz (250 kHz)

25°C

dBc

110 MHz (50 kHz)

25°C

dBc

110 MHz (10 kHz)

25°C

dBc

140 MHz (1 MHz)

25°C

dBc

140 MHz (250 kHz)

25°C

dBc

140 MHz (50 kHz)

25°C

dBc

140 MHz (10 kHz)

25°C

dBc

160 MHz (1 MHz)

25°C

dBc

160 MHz (250 kHz)

25°C

dBc

160 MHz (50 kHz)

25°C

dBc

160 MHz (10 kHz)

25°C

dBc

CLOCK GENERATOR OUTPUT JITTER

5 MHz A

OUT

25°C

100

ps RMS

10 MHz A

OUT

25°C V

RMS

40 MHz A

OUT

25°C V

RMS

80 MHz A

OUT

25°C V

RMS

120 MHz A

OUT

25°C V

RMS

140 MHz A

OUT

25°C V

RMS

160 MHz A

OUT

25°C V

RMS

TIMING CHARACTERISTICS

Serial Control Bus

FULL

Maximum Frequency

FULL

Mbps

Minimum Clock Pulse Width Low

FULL

Minimum Clock Pulse Width High

FULL

Maximum Clock Rise/Fall Time

FULL

Minimum Data Setup Time DVDD_I/O = 3.3 V

FULL

Minimum Data Setup Time DVDD_I/O = 1.8 V

FULL

Minimum Data Hold Time

FULL

AD9954

Rev. 0 | Page 6 of 36

Parameter

Temp

Test
Level

Min

Typ

Max

Unit

Maximum Data Valid Time

FULL

Wake-Up Time

FULL IV

Minimum Reset Pulse Width High

FULL

SYSCLK Cycles

I/O UPDATE, PS0, PS1 to SYNCCLK Setup Time DVDD_I/O = 3.3 V

FULL

I/O UPDATE, PS0, PS1 to SYNCCLK Setup Time DVDD_I/O = 3.3 V

FULL

I/O UPDATE, PS0, PS1 to SYNCCLK Hold Time

FULL

Latency

I/O UPDATE to Frequency Change Prop Delay 25°C

SYSCLK

Cycles

I/O UPDATE to Phase Offset Change Prop Delay

25°C

SYSCLK Cycles

I/O UPDATE to Amplitude Change Prop Delay 25°C

SYSCLK

Cycles

PS0, PS1 to RAM Driven Frequency Change Prop Delay

25°C

SYSCLK Cycles

PS0, PS1 to RAM Driven Phase Change Prop Delay

25°C

SYSCLK Cycles

PS0 to Linear Frequency Sweep Prop Delay 25°C

SYSCLK

Cycles

CMOS LOGIC INPUTS

Logic 1 Voltage @ DVDD_I/O (Pin 43) = 1.8 V

25°C

1.25

Logic 0 Voltage @ DVDD_I/O (Pin 43) = 1.8 V

25°C

0.6

Logic 1 Voltage @ DVDD_I/O (Pin 43) = 3.3 V

25°C

2.2

Logic 0 Voltage @ DVDD_I/O (Pin 43) = 3.3 V

25°C

0.8

Logic 1 Current

25°C

µA

Logic 0 Current

25°C

µA

Input Capacitance

25°C

CMOS LOGIC OUTPUTS (1 mA Load) DVDD_I/O = 1.8 V

Logic 1 Voltage

25°C

1.35

Logic 0 Voltage

25°C

0.4

CMOS LOGIC OUTPUTS (1 mA Load) DVDD_I/O = 3.3 V

Logic 1 Voltage

25°C

2.8

Logic 0 Voltage

25°C

0.4

POWER CONSUMPTION (AVDD = DVDD = 1.8 V)

Single Tone Mode (Comparator Off)

25°C

162

171

With RAM or Linear Sweep Enabled

25°C

175

190

With Comparator Enabled

25°C

180

190

With RAM and Comparator Enabled

25°C

198

220

Rapid Power-Down Mode

25°C

150

160

Full-Sleep Mode

25°C

SYNCHRONIZATION FUNCTION

Maximum SYNC Clock Rate (DVDD_I/O = 1.8 V)

25°C

62.5

MHz

Maximum SYNC Clock Rate (DVDD_I/O = 3.3 V)

25°C

100

MHz

SYNC_CLK Alignment Resolution

25°C V

±1

SYSCLK

Cycles

To achieve the best possible phase noise, the largest amplitude clock possible should be used. Reducing the clock input amplitude will reduce the phase noise per-

formance of the device.

Represents the cycle-to-cycle residual jitter from the comparator alone.

Represents the cycle-to-cycle residual jitter from the DDS core driving the comparator.

Wake-up time refers to the recovery from analog power-down modes (see section on Power-Down Modes of Operation). The longest time required is for the reference

clock multiplier PLL to relock to the reference. The wake-up time assumes there is no capacitor on DAC_BP and that the recommended PLL loop filter values are used.

SYSCLK cycle refers to the actual clock frequency used on-chip by the DDS. If the reference clock multiplier is used to multiply the external reference clock frequency,

the SYSCLK frequency is the external frequency multiplied by the reference clock multiplication factor. If the reference clock multiplier is not used, the SYSCLK fre-
quency is the same as the external reference clock frequency.

SYNC_CLK = ј SYSCLK rate. For SYNC_CLK rates

50 MHz, the high speed sync enable bit, CFR2<11>, should be set.

This parameter indicates that the digital synchronization feature cannot overcome phase delays (timing skew) between system clock rising edges. If the system clock

edges are aligned, the synchronization function should not increase the skew between the two edges.

AD9954

Rev. 0 | Page 7 of 36

ABSOLUTE MAXIMUM RATINGS

Table 2.

Parameter Rating

Maximum Junction Temperature

150°C

DVDD_I/O (Pin 43)

4 V

AVDD, DVDD

2 V

Digital Input Voltage (DVDD_I/O = 3.3 V)

0.7 V to +5.25 V

Digital Input Voltage (DVDD_I/O = 1.8 V)

0.7 V to +2.2 V

Digital Output Current

5 mA

Storage Temperature

65°C to +150°C

Operating Temperature

40°C to +105°C

Lead Temperature (10 sec Soldering)

300°C

38°C/W

15°C/W

Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress rat-
ing only and functional operation of the device at these or any
other conditions above those indicated in the operational sec-
tion of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.

Table 3. Explanation of Test Levels

100% Production Tested.

100% Production Tested at 25°C and sample Tested at
Specified Temperatures.

III

Sample Tested Only.

Parameter is guaranteed by design and characterization
testing.

Parameter is a typical value only.

Devices are 100% production tested at 25°C and
guaranteed by design and characterization testing for
industrial operating temperature range.

7
4-

IOUT

MUST TERMINATE

OUTPUTS TO AVDD FOR

CURRENT FLOW. DO

NOT EXCEED THE

OUTPUT VOLTAGE

COMPLIANCE RATING.

DAC OUTPUTS

AVDD

COMPARATOR

OUTPUT

DVDD_I/O

INPUT

DIGITAL

INPUTS

AVOID OVERDRIVING

DIGITAL INPUTS.

FORWARD BIASING

ESD DIODES MAY

COUPLE DIGITAL NOISE

ONTO POWER PINS.

AVDD

COMP IN

COMPARATOR

INPUTS

Figure 2. Equivalent Input and Output Circuits

AD9954

Rev. 0 | Page 8 of 36

PIN CONFIGURATIONS

I / O U P D A T E

D V D D

D G N D

A V D D

A G N D

A V D D

A G N D

O S C / R E F C L K

C R Y S T A L O U T

C L K M O D E S E L E C T

L O O P _ F I L T E R

AGND

IOUT

DACBP

AGND

OSK

PS1

PS0

NC_

CLK

NC_

DD_

I
/O

DGND

IOSYN

R E S E T

P W R D W N C T L

D V D D

D G N D

A G N D

C O M P _ I N

A V D D

C O M P _ O U T

A V D D

A G N D

A V D D

A D 9954

TOP V IE W

( Not t o S c a le )

03374-0-002

DAC_

SET

Figure 3. 48-Lead EP_TQFP

Note that the exposed paddle on the bottom of the package forms an electrical connection for the DAC and must be attached to
analog ground. Note that Pin 43, DVDD_I/O, can be powered to 1.8 V or 3.3 V. The DVDD pins (Pin 2 and Pin 34) can only be
powered to 1.8 V.

AD9954

Rev. 0 | Page 9 of 36

PIN FUNCTION DESCRIPTIONS

Table 4. Pin Function Descriptions--48-Lead TQFP/EP

Pin No.

Mnemonic

I/O

Description

1 I/O

UPDATE

The rising edge transfers the contents of the internal buffer memory to the I/O registers. This pin
must be set up and held around the SYNC_CLK output signal.

2, 34

DVDD

Digital Power Supply Pins (1.8 V).

3, 33, 42

DGND

Digital Power Ground Pins.

4, 6, 13, 16,
18, 19, 25,
27, 29

AVDD

Analog Power Supply Pins (1.8 V).

5, 7, 14, 15,
17, 22, 26,
32

AGND

Analog Power Ground Pins.

OSC/REFCLK

Complementary Reference Clock/Oscillator Input. When the REFCLK port is operated in single-
ended mode, REFCLKB should be decoupled to AVDD with a 0.1 µF capacitor.

9 OSC/REFCLK

Reference Clock/Oscillator Input. See Clock Input section for details on the OSCILLATOR/REFCLK
operation.

CRYSTAL OUT

Output of the Oscillator Section.

11 CLKMODESELECT

Control Pin for the Oscillator Section. When high, the oscillator section is enabled. When low, the
oscillator section is bypassed.

12 LOOP_FILTER

This pin provides the connection for the external zero compensation network of the REFCLK
multiplier's PLL loop filter. The network consists of a 1 k resistor in series with a 0.1 µF capacitor
tied to AVDD.

IOUT

Complementary DAC Output. Should be biased through a resistor to AVDD, not AGND.

IOUT

DAC Output. Should be biased through a resistor to AVDD, not AGND.

DACBP

DAC Biasline Decoupling Pin.

24 DAC_R

SET

A resistor (3.92 k nominal) connected from AGND to DAC_R

SET

establishes the reference current

for the DAC.

28 COMP_OUT

Comparator

Output.

30 COMP_IN

Comparator

Input.

COMP_IN

Comparator Complementary Input.

PWRDWNCTL

Input Pin Used as an External Power-Down Control (see Table 13 for details).

36 RESET I

Active High Hardware Reset Pin. Assertion of the RESET pin forces the AD9954 to the initial state,
as described in the I/O port register map.

37 IOSYNC I

Asynchronous Active High Reset of the Serial Port Controller. When high, the current I/O
operation is immediately terminated, enabling a new I/O operation to commence once IOSYNC is
returned low. If unused, ground this pin; do not allow this pin to float.

38 SDO

When operating the I/O port as a 3-wire serial port, this pin serves as the serial data output. When
operated as a 2-wire serial port, this pin is unused and can be left unconnected.

This pin functions as an active low chip select that allows multiple devices to share the I/O bus.

SCLK

This pin functions as the serial data clock for I/O operations.

41 SDIO

I/O

When operating the I/O port as a 3-wire serial port, this pin serves as the serial data input, only.
When operated as a 2-wire serial port, this pin is the bidirectional serial data pin.

DVDD_I/O

Digital Power Supply (for I/O Cells Only, 3.3 V).

44 SYNC_IN

Input signal used to synchronize multiple AD9954s. This input is connected to the SYNC_CLK
output of a master AD9954.

SYNC_CLK

Clock Output Pin that Serves as a Synchronizer for External Hardware.

46 OSK

Input pin used to control the direction of the shaped on-off keying function when programmed
for operation. OSK is synchronous to the SYNC_CLK pin. When OSK is not programmed, this pin
should be tied to DGND.

47, 48

PS0, PS1

Input pin used to select one of the four internal profiles. Profile <1:0> are synchronous to the
SYNC_CLK pin. Any change in these inputs transfers the contents of the internal buffer memory
to the I/O registers (sends an internal I/O UPDATE).

<49> AGND

The exposed paddle on the bottom of the package is a ground connection for the DAC and must
be attached to AGND in any board layout.

AD9954

Rev. 0 | Page 10 of 36

TYPICAL PERFORMANCE CHARACTERISTICS

CENTER 100MHz
#RES BW 3kHz

100

90

80

70

60

50

40

30

20

10

VBW 3kHz

SPAN 200MHz

SWEEP 55.56 s (401 PTS)

W1 S2

S3 FC

REF 0dBm

PEAK

LOG

10dB/

ATTEN 10dB

MKR1 98.0MHz

70.68dB

03374-0-016

MARKER
100.000000MHz
70.68dB

Figure 4. F

OUT

= 1 MHz FCLK = 400 MSPS, WBSFDR

CENTER 100MHz
#RES BW 3kHz

100

90

80

70

60

50

40

30

20

10

VBW 3kHz

SPAN 200MHz

SWEEP 55.56 s (401 PTS)

W1 S2

S3 FC

REF 0dBm

PEAK

LOG

10dB/

ATTEN 10dB

MKR1 80.0MHz

69.12dB

03374-0-017

MARKER
80.000000MHz
69.12dB

Figure 5. F

OUT

= 10 MHz, FCLK = 400 MSPS, WBSFDR

CENTER 100MHz
#RES BW 3kHz

100

90

80

70

60

50

40

30

20

10

VBW 3kHz

SPAN 200MHz

SWEEP 55.56 s (401 PTS)

W1 S2

S3 FC

REF 0dBm

PEAK

LOG

10dB/

ATTEN 10dB

MKR1 0Hz

68.44dB

03374-0-018

MARKER
40.000000MHz
68.44dB

Figure 6. F

OUT

= 40 MHz, FCLK = 400 MSPS, WBSFDR

CENTER 100MHz
#RES BW 3kHz

100

90

80

70

60

50

40

30

20

10

VBW 3kHz

SPAN 200MHz

SWEEP 55.56 s (401 PTS)

W1 S2

S3 FC

REF 0dBm

PEAK

LOG

10dB/

ATTEN 10dB

MKR1 80.0MHz

61.55dB

03374-0-019

MARKER
80.000000MHz
61.55dB

Figure 7. F

OUT

= 80 MHz FCLK = 400 MSPS, WBSFDR

CENTER 100MHz
#RES BW 3kHz

100

90

80

70

60

50

40

30

20

10

VBW 3kHz

SPAN 200MHz

SWEEP 55.56 s (401 PTS)

W1 S2

S3 FC

REF 0dBm

PEAK

LOG

10dB/

ATTEN 10dB

MKR1 40.0MHz

56.2dB

03374-0-020

MARKER
40.000000MHz
56.2dB

Figure 8 F

OUT

= 120 MHz, FCLK = 400 MSPS, WBSFDR

CENTER 100MHz
#RES BW 3kHz

100

90

80

70

60

50

40

30

20

10

VBW 3kHz

SPAN 200MHz

SWEEP 55.56 s (401 PTS)

W1 S2

S3 FC

REF 0dBm

PEAK

LOG

10dB/

ATTEN 10dB

MKR1 0Hz

53.17dB

03374-0-021

MARKER
80.000000MHz
53.17dB

Figure 9. F

OUT

= 160 MHz, FCLK = 400 MSPS, WBSFDR

AD9954

Rev. 0 | Page 11 of 36

CENTER 1.105MHz
#RES BW 30Hz

100

90

80

70

60

50

40

30

20

10

VBW 30Hz

SPAN 2MHz

SWEEP 199.2 s (401 PTS)

W1 S2

S3 FC

REF 4dBm

PEAK

LOG

10dB/

ATTEN 10dB

MKR1 1.105MHz

5.679dBm

03374-0-022

MARKER
1.105000MHz
5.679dBm

Figure 10. F

OUT

= 1.1 MHz, FCLK = 400 MSPS, NBSFDR, ±1 MHz

CENTER 10MHz
#RES BW 30Hz

100

90

80

70

60

50

40

30

20

10

VBW 30Hz

SPAN 2MHz

SWEEP 199.2 s (401 PTS)

W1 S2

S3 FC

REF 0dBm

PEAK

LOG

10dB/

ATTEN 10dB

MKR1 85kHz

93.01dB

03374-0-023

MARKER
40.000000MHz
56.2dB

Figure 11. F

OUT

= 10 MHz, FCLK = 400 MSPS, NBSFDR, ±1 MHz

CENTER 39.9MHz
#RES BW 30Hz

100

90

80

70

60

50

40

30

20

10

VBW 30Hz

SPAN 2MHz

SWEEP 199.2 s (401 PTS)

W1 S2

S3 FC

REF 0dBm

PEAK

LOG

10dB/

ATTEN 10dB

MKR1 39.905MHz

5.347dBm

03374-0-024

MARKER
39.905000MHz
5.347dBm

Figure 12. F

OUT

= 39.9 MHz, FCLK = 400 MSPS, NBSFDR, ±1 MHz

CENTER 80.25MHz
#RES BW 30Hz

100

90

80

70

60

50

40

30

20

10

VBW 30Hz

SPAN 2MHz

SWEEP 199.2 s (401 PTS)

W1 S2

S3 FC

REF 4dBm

PEAK

LOG

10dB/

ATTEN 10dB

MKR1 80.301MHz

6.318dBm

03374-0-025

MARKER
80.301000MHz
6.318dBm

Figure 13. F

OUT

= 80.3 MHz, FCLK = 400 MSPS, NBSFDR, ±1 MHz

CENTER 120.2MHz
#RES BW 30Hz

100

90

80

70

60

50

40

30

20

10

VBW 30Hz

SPAN 2MHz

SWEEP 199.2 s (401 PTS)

W1 S2

S3 FC

REF 4dBm

PEAK

LOG

10dB/

ATTEN 10dB

MKR1 120.205MHz

6.825dBm

03374-0-026

MARKER
120.205000MHz
6.825dBm

Figure 14. F

OUT

= 120.2 MHz, FCLK = 400 MSPS, NBSFDR, ±1 MHz

CENTER 160.5MHz
#RES BW 30Hz

100

90

80

70

60

50

40

30

20

10

VBW 30Hz

SPAN 2MHz

SWEEP 199.2 s (401 PTS)

W1 S2

S3 FC

REF 4dBm

PEAK

LOG

10dB/

ATTEN 10dB

MKR1 600kHz

0.911dB

03374-0-027

CENTER
160.5000000MHz

Figure 15. F

OUT

= 160 MHz, FCLK = 400 MSPS, NBSFDR, ±1 MHz

AD9954

Rev. 0 | Page 13 of 36

THEORY OF OPERATION

COMPONENT BLOCKS

DDS Core

The output frequency (f

) of the DDS is a function of the fre-

quency of system clock (SYSCLK), the value of the frequency
tuning word (FTW), and the capacity of the accumulator (2

, in

this case). The exact relationship is given below with f

defined

as the frequency of SYSCLK.

(

)

( )

FTW

with

FTW

(

)

(

)

FTW

with

FTW

The value at the output of the phase accumulator is translated to
an amplitude value via the COS(x) functional block and routed
to the DAC.

In certain applications it is desirable to force the output signal to
zero phase. Simply setting the FTW to 0 does not accomplish
this; it only results in the DDS core holding its current phase
value. Thus, a control bit is required to force the phase accumu-
lator output to zero.

At power-up, the clear phase accumulator bit is set to Logic 1,
but the buffer memory for this bit is cleared (Logic 0). There-
fore, upon power-up, the phase accumulator will remain clear
until the first I/O UPDATE is issued.

Phase-Locked Loop (PLL)

The PLL allows multiplication of the REFCLK frequency. Con-
trol of the PLL is accomplished by programming the 5-bit
REFCLK multiplier portion of Control Function Register No. 2,
Bits <7:3>.

When programmed for values ranging from 0x04 to 0x14
(4 decimal to 20 decimal), the PLL multiplies the REFCLK input
frequency by the corresponding decimal value. However, the
maximum output frequency of the PLL is restricted to
400 MHz. Whenever the PLL value is changed, the user should
be aware that time must be allocated to allow the PLL to lock
(approximately 1 ms).

The PLL is bypassed by programming a value outside the range
of 4 to 20 (decimal). When bypassed, the PLL is shut down to
conserve power.

Clock Input

The AD9954 supports various clock methodologies. Support for
differential or single-ended input clocks, and enabling of an on-
chip oscillator, and/or a phase-locked loop (PLL) multiplier are
all controlled via user programmable bits. The AD9954 may be
configured in one of six operating modes to generate the system
clock. The modes are configured using the CLKMODESELECT
pin, CFR1<4> and CFR2<7:3>. Connecting the external pin
CLKMODESELECT to Logic High enables the on-chip crystal
oscillator circuit. With the on-chip oscillator enabled, users of
the AD9954 connect an external crystal to the REFCLK and
REFCLKB inputs to produce a low frequency reference clock in
the range of 20 MHz to 30 MHz. The signal generated by the
oscillator is buffered before it is delivered to the rest of the chip.
This buffered signal is available via the CRYSTAL OUT pin. Bit
CFR1<4> can be used to enable or disable the buffer, turning on
or off the system clock. The oscillator itself is not powered
down in order to avoid long startup times associated with turn-
ing on a crystal oscillator. Writing CFR2<9> to Logic High
enables the crystal oscillator output buffer. Logic Low at
CFR2<9> disables the oscillator output buffer.

Connecting CLKMODESELECT to Logic Low disables the on-
chip oscillator and the oscillator output buffer. With the oscilla-
tor disabled, an external oscillator must provide the REFCLK
and/or REFCLKB signals. For differential operation, these pins
are driven with complementary signals. For single-ended opera-
tion, a 0.1 µF capacitor should be connected between the
unused pin and the analog power supply. With the capacitor in
place, the clock input pin bias voltage is 1.35 V. In addition, the
PLL may be used to multiply the reference frequency by an
integer value in the range of 4 to 20. Table 5 summarizes the
clock modes of operation. Note the PLL multiplier is controlled
via the CFR2<7:3> bits, independent of the CFR1<4> bit.

Table 5.Clock Input Modes of Operation

CFR1<4> CLKMODESELECT CFR2<7:3>

Oscillator

Enabled?

System Clock

Frequency Range (MHz)

Low

High

3 < M < 21

Yes

CLK

= F

OSC

Ч M

80 < F

CLK

< 400

Low

High

M < 4 or M > 20

Yes

CLK

= F

OSC

20 < F

CLK

< 30

Low

3 < M < 21

CLK

= F

OSC

Ч M

80 < F

CLK

< 400

Low

M < 4 or M > 20

CLK

= F

OSC

10 < F

CLK

< 400

High X

CLK

= 0

N/A

AD9954

Rev. 0 | Page 14 of 36

DAC Output

The AD9954 incorporates an integrated 14-bit current output
DAC. Unlike most DACs, this output is referenced to AVDD,
not AGND.

Two complementary outputs provide a combined full-scale
output current (I

OUT

). Differential outputs reduce the amount of

common-mode noise that might be present at the DAC output,
offering the advantage of an increased signal-to-noise ratio. The
full-scale current is controlled by means of an external resistor
(R

SET

) connected between the DAC_R

SET

pin and the DAC

ground (AGND_DAC). The full-scale current is proportional to
the resistor value as follows

OUT

SET

The maximum full-scale output current of the combined DAC
outputs is 15 mA, but limiting the output to 10 mA provides the
best spurious-free dynamic range (SFDR) performance. The DAC
output compliance range is AVDD + 0.5 V to AVDD 0.5 V. Volt-
ages developed beyond this range will cause excessive DAC distor-
tion and could potentially damage the DAC output circuitry.
Proper attention should be paid to the load termination to keep the
output voltage within this compliance range.

Comparator

Many applications require a square wave signal rather than a
sine wave. For example, in most clocking applications a high
slew rate helps to reduce phase noise and jitter. To support these
applications, the AD9954 includes an on-chip comparator. The
comparator has a bandwidth greater than 200 MHz and a
common-mode input range of 1.3 V to 1.8 V. By setting the
comparator power-down bit, CFR1<6>, the comparator can be
turned off to save on power consumption.

Linear Sweep Block

Linear sweep is a mode of operation whereby changes from a
start frequency (F0) to a terminal frequency (F1) are not instan-
taneous but instead are accomplished in a sweep or ramped
fashion. Frequency ramping, whether linear or nonlinear, neces-
sitates that many intermediate frequencies between F0 and F1
will be output in addition to the primary F0 and F1 frequencies.

The linear sweep block is comprised of the falling and rising
delta frequency tuning words, the falling and rising delta fre-
quency ramp rates, and the frequency accumulator. The linear
sweep enable bit CFR1 <21> enables the linear sweep block. In

addition, the linear sweep no dwell bit controls the linear sweep
block's behavior upon reaching the terminal frequency in a
sweep. The actual method for programming a frequency sweep
is covered in the Modes of Operation section.

Serial IO Port

The AD9954 serial port is a flexible, synchronous serial communi-
cations port that allows easy interface to many industry-standard
microcontrollers and microprocessors. The serial I/O port is com-
patible with most synchronous transfer formats, including both the
Motorola 6905/11 SPI and Intel 8051 SSR protocols.

The interface allows read/write access to all registers that configure
the AD9954. MSB first or LSB first transfer formats are supported.
In addition, the AD9954's serial interface port can be configured as
a single pin I/O (SDIO), which allows a 2-wire interface or two
unidirectional pins for in/out (SDIO/SDO), which enables a 3-wire
interface. Two optional pins, IOSYNC and CS, enable greater flexi-
bility for system design in the AD9954.

Register Maps and Descriptions

The register maps are listed in Table 7 and Table 8. The appro-
priate register map depends on the state of the linear sweep
enable bit because certain registers are remapped depending
on which mode the part is operating in

. Specifically, Registers

0x07, 0x08, 0x09, and 0x0A act as the RAM segment control
words for each of the RAM profile slices when the linear sweep
enable bit is false. When the linear sweep enable bit is true, 0x07
becomes the negative linear sweep control word and 0x08
becomes the positive linear sweep control word. The 0x09 and
0x0A registers are not used in linear sweep mode. Because the
linear sweep operation takes precedence over RAM operations,
ADI recommends that the RAM enable bit CFR1<31> be set to
zero when the linear sweep enable bit CFR1<21> is true to
conserve power. The serial address numbers associated with
each of the registers are shown in hexadecimal format. Angle
brackets <> are used to reference specific bits or ranges of bits.
For example, <3> designates Bit 3, while <7:3> designates the
range of bits from 7 down to 3, inclusive.

Table 6. Register Mapping Based on Linear Sweep Enable Bit

Linear Sweep Enable Bit

Register Map

False (CFR1 <21> = 0)

RAM Segment Control Words Active

True (CFR1 <21> = 1)

Linear Sweep Control Words Active

AD9954

Rev. 0 | Page 15 of 36

Table 7. Register Map--When Linear Sweep Enable Bit Is False (CFR1<21> = 0).

Note that the RAM enable Bit CFR1<31> only activates the RAM itself not the RAM segment control words.

Bit
Range

(MSB)
Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

(LSB)
Bit 0

Default
Value
OR
Profile

<7:0>

Digital

Power-

Down

Comp

Power-

Down

DAC

Power-

Down

Clock Input

Power-

Down

External

Power-

Down

Mode

Linear

Sweep No

Dwell

SYNC_CLK

Out

Disable

Not

Used

0x00

<15:8>

Load SRR

@ I/O UD

AutoClr

Freq.

Accum

AutoClr

Phase

Accum

Enable

SINE

Output

Clear

Freq

Accum.

Clear

Phase

Accum.

SDIO

Input

Only

LSB First

0x00

<23:16>

Automatic

Sync

Enable

Software

Manual

Sync

Linear

Sweep
Enable

Not Used

Not

Used

0x00

Control

Function

No.1

(CFR1)

(0x00)

<31:24>

RAM

Enable

RAM

Dest. Is

Phase

Word

Internal Profile Control <2:0>

Load ARR

@ I/O UD

OSK

Enable

Auto

OSK

Keying

0x00

<7:0>

REFCLK Multiplier

0x00 or 0x01, or 0x02 or 0x03: Bypass Multiplier

0x04 to 0x14: 4Ч to 20Ч Multiplication

VCO Range

Charge Pump Current

<1:0>

0x00

<15:8> Not

Used

High

Speed

Sync

Enable

Hardware

Manual

Sync

Enable

CRYSTAL

OUT Pin

Active

Not

Used

0x00

Control

Function

2 (CFR2)

(0x01)

<23:16> Not

Used 0x00

<7:0>

Amplitude Scale Factor Register <7:0>

0x00

Amplitude

Scale Factor

(ASF)

(0x02)

<15:8>

Auto Ramp Rate Speed

Control <1:0>

Amplitude Scale Factor Register <13:8>

0x00

Amplitude
Ramp Rate

(ARR)

(0x03)

<7:0>

Amplitude Ramp Rate Register <7:0>

0x00

<7:0>

Frequency Tuning Word No. 0 <7:0>

0x00

<15:8>

Frequency Tuning Word No. 0 <15:8>

0x00

<23:16>

Frequency Tuning Word No. 0 <23:16>

0x00

Frequency

Tuning

Word

(FTW0)

(0x04)

<31:24>

Frequency Tuning Word No. 0 <31:24>

0x00

<7:0>

Phase Offset Word No. 0 <7:0>

0x00

Phase

Offset Word

(POW0)

(0x05)

<15:8> Not

Used<1:0>

Phase

Offset Word No. 0 <13:8>

0x00

<7:0>

Frequency Tuning Word No. 1 <7:0>

0x00

<15:8>

Frequency Tuning Word No. 1 <15:8>

0x00

<23:16>

Frequency Tuning Word No. 1 <23:16>

0x00

Frequency

Tuning

Word

(FTW1)

(0x06)

<31:24>

Frequency Tuning Word No. 1 <31:24>

0x00

AD9954

Rev. 0 | Page 16 of 36

Bit
Range

(MSB)
Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

(LSB)
Bit 0

Default
Value
OR
Profile

<7:0>

RAM Segment 0 Mode Control <2:0>

No Dwell

Active

RAM Segment 0 Beginning Address <9:6>

PS0 = 0
PS1 = 0

<15:8>

RAM Segment 0 Beginning Address <5:0>

RAM Segment 0 Final Address <9:8>

PS0 = 0
PS1 = 0

<23:16>

RAM Segment 0 Final Address <7:0>

PS0 = 0
PS1 = 0

<31:24>

RAM Segment 0 Address Ramp Rate <15:8>

PS0 = 0
PS1 = 0

RAM

Segment

Control

Word No. 0

(RSCW0)

(0x07)

<39:32>

RAM Segment 0 Address Ramp Rate <7:0>

PS0 = 0
PS1 = 0

<7:0>

RAM Segment 1 Mode Control

<2:0>

No Dwell

Active

RAM Segment 1 Beginning Address <9:6>

PS0 = 0
PS1 = 1

<15:8>

RAM Segment 1 Beginning Address <5:0>

RAM Segment 1 Final Address <9:8>

PS0 = 0
PS1 = 1

<23:16>

RAM Segment 1 Final Address <7:0>

PS0 = 0
PS1 = 1

<31:24>

RAM Segment 1 Address Ramp Rate <15:8>

PS0 = 0
PS1 = 1

RAM

Segment

Control

Word No. 1

(RSCW1)

(0x08)

<39:32>

RAM Segment 1 Address Ramp Rate <7:0>

PS0 = 0
PS1 = 1

<7:0>

RAM Segment 2 Mode Control

<2:0>

No Dwell Active

RAM Segment 2 Beginning

Address <9:6>

PS0 = 1
PS1 = 0

<15:8>

RAM Segment 2 Beginning Address <5:0>

RAM Segment 2 Final Address <9:8>

PS0 = 1
PS1 = 0

<23:16>

RAM Segment 2 Final Address <7:0>

PS0 = 1
PS1 = 0

<31:24>

RAM Segment 2 Address Ramp Rate <15:8>

PS0 = 1
PS1 = 0

RAM

Segment

Control

Word No. 2

(RSCW2)

(0x09)

<39:32>

RAM Segment 2 Address Ramp Rate <7:0>

PS0 = 1
PS1 = 0

<7:0>

RAM Segment 3 Mode Control

<2:0>

No Dwell Active

RAM Segment 3 Beginning

Address <9:6>

PS0 = 1
PS1 = 1

<15:8>

RAM Segment 3 Beginning Address <5:0>

RAM Segment 3 Final Address <9:8>

PS0 = 1
PS1 = 1

<23:16>

RAM Segment 3 Final Address <7:0>

PS0 = 1
PS1 = 1

<31:24>

RAM Segment 3 Address Ramp Rate <15:8>

PS0 = 1
PS1 = 1

RAM

Segment

Control

Word No. 3

(RSCW3)

(0x0A)

<39:32>

RAM Segment 3 Address Ramp Rate <7:0>

PS0 = 1
PS1 = 1

RAM (0x0B)

RAM [1023:0] <31:0> (Read Instructions Write Out RAM Signature Register Data)

AD9954

Rev. 0 | Page 17 of 36

Table 8. Register MapWhen Linear Sweep Enable Bit Is True (CFR1<21> = 1).

Note that the RAM enable Bit CFR1<31> only activates the RAM itself not the RAM segment control words.

Bit Range

(MSB)
Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

(LSB)
Bit 0

Default
Value
OR
Profile

<7:0>

Digital

Power-

Down

Comp

Power-

Down

DAC

Power-

Down

Clock
Input

Power

Dwn

External

Power-

Down

Mode

CRYSTAL

OUT Pin

Active

SYNC_CLK

Out

Disable

Not

Used

0x00

<15:8>

Load SRR

@ I/O UD

AutoClr

Freq.

Accum

AutoClr

Phase

Accum

Enable

SINE

Output

Clear

Freq

Accum.

Clear

Phase

Accum.

SDIO

Input

Only

LSB First

0x00

<23:16>

Automatic

Sync

Enable

Software

Manual

Sync

Linear

Sweep
Enable

Not Used

Not

Used

Not Used

Not

Used

0x00

Control

Function

1 (CFR1)

(0x00)

<31:24>

RAM

Enable

RAM

Dest. Is

Phase

Word

Internal Profile Control <2:0>

Load ARR

@ I/O UD

Output

Shaped

Keying
Enable

Auto

Output

Shaped

Keying

0x00

<7:0>

REFCLK Multiplier

0x00 or 0x1 or 0x02 or 0x03: Bypass Multiplier

0x04 to 0x14: 4Ч to 20Ч Multiplication

VCO

Range

Charge Pump Current

<1:0>

0x00

<15:8> Not

Used

High

Speed

Sync

Enable

Hardware

Manual

Sync

Enable

CRYSTAL

OUT Pin

Active

Not

Used

0x00

Control

Function

2 (CFR2)

(0x01)

<23:16> Not

Used 0x00

<7:0>

(0x07)

Amplitude Scale Factor Register <7:0>

Amplitude

Scale Factor
(ASF) (0x02)

<15:8>

Auto Ramp Rate

Speed Control <1:0>

Amplitude Scale Factor Register <13:8>

Amplitude
Ramp Rate

(ARR) (0x03)

<7:0>

Amplitude Ramp Rate Register <7:0>

<7:0>

Frequency Tuning Word No. 0 <7:0>

0x00

<15:8>

Frequency Tuning Word No. 0 <15:8>

0x00

<23:16>

Frequency Tuning Word No. 0 <23:16>

0x00

Frequency

Tuning

Word

(FTW0)

(0x04)

<31:24>

Frequency Tuning Word No. 0 <31:24>

0x00

<7:0>

Phase Offset Word No. 0 <7:0>

0x00

Phase Offset

Word

(POW0)

(0x05)

<15:8> Open<1:0>

Phase

Offset Word No. 0 <13:8>

0x00

<7:0>

Frequency Tuning Word No. 1 <7:0>

<15:8>

Frequency Tuning Word No. 1 <15:8>

<23:16>

Frequency Tuning Word No. 1 <23:16>

Frequency

Tuning

Word

(FTW1)

(0x06)

<31:24>

Frequency Tuning Word No. 1 <31:24>

<7:0>

Falling Delta Frequency Tuning Word <7:0>

PS0 = 0

<15:8>

Falling Delta Frequency Tuning Word <15:8>

PS0 = 0

<23:16>

Falling Delta Frequency Tuning Word <23:16>

PS0 = 0

<31:24>

Falling Delta Frequency Tuning Word <31:24>

PS0 = 0

Negative

Linear

Sweep

Control

Word

(NLSCW)

(0x07)

<39:32>

Falling Sweep Ramp Rate Word <7:0>

PS0 = 0

AD9954

Rev. 0 | Page 18 of 36

Bit Range

(MSB)
Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

(LSB)
Bit 0

Default
Value
OR
Profile

<7:0>

Rising Delta Frequency Tuning Word <7:0>

PS0 = 1

<15:8>

Rising Delta Frequency Tuning Word <15:8>

PS0 = 1

<23:16>

Rising Delta Frequency Tuning Word <23:16>

PS0 = 1

<31:24>

Rising Delta Frequency Tuning Word <31:24>

PS0 = 1

Positive

Linear

Sweep

Control

Word

(PLSCW)

(0x08)

<39:32>

Rising Sweep Ramp Rate Word <7:0>

PS0 = 1

Control Register Bit Descriptions

Control Function Register No.1 (CFR1)

The CFR1 is used to control the various functions, features,
and modes of the AD9954. The functionality of each bit is
detailed below.

CFR1<31>: RAM Enable Bit

CFR1<31> = 0 (default). When CFR1<31> is inactive, the RAM
is disabled for operation. Either single-tone mode of
operation or linear sweep mode of operation is enabled.

CFR1<31> = 1. If CFR1<31> is active, the RAM is
enabled for operation. Access control for normal operation is
controlled via the mode control bits of the RSCW for the cur-
rent profile.

CFR1<30>: RAM Destination Bit

CFR1<30> = 0 (default). If CFR1<31> is active, a Logic 0 on the
RAM destination bit (CFR1<30> = 0) configures the AD9954
such that the RAM output drives the phase accumulator (i.e.,
the frequency tuning word). If CFR1<31> is inactive,
CFR1<30> is a Don't Care.

CFR1<30> = 1. If CFR1<31> is active, a Logic 1 on the RAM
destination bit (CFR1<30> = 1) configures the AD9954 such
that the RAM output drives the phase-offset adder (i.e., sets the
phase offset of the DDS core).

CFR1<29:27>: Internal Profile Control Bits

These bits cause the profile bits to be ignored when the RAM is
being used and puts the AD9954 into an automatic profile loop
sequence that allows the user to implement a frequency/phase
composite sweep that runs without external inputs. See the
Internal Profile Control section for more details.

CFR1<26>: Amplitude Ramp Rate Load Control Bit

CFR1<26> = 0 (default). The amplitude ramp rate timer is
loaded only upon timeout (timer == 1) and is not loaded due to
an I/O UPDATE input signal.

CFR1<26> = 1. The amplitude ramp rate timer is loaded upon
timeout (timer == 1) or at the time of an I/O UPDATE input signal.

CFR1<25>: Shaped On-Off Keying Enable Bit

CFR1<25> = 0 (default) Shaped on-off keying is
bypassed.

CFR1<25> = 1. Shaped on-off keying is enabled. When enabled,
CFR1<24> controls the mode of operation for this function.

CFR1<24>: Auto Shaped On-Off Keying Enable Bit (Only Valid
When CFR1<25> Is Active High)

CFR1<24> = 0 (default). When CFR1<25> is active, a Logic 0
on CFR1<24> enables the manual shaped on-off keying opera-
tion. Each amplitude sample sent to the DAC is multiplied by
the amplitude scale factor. See the Shaped On-Off Keying sec-
tion for details.

CFR1<24> = 1. When CFR1<25> is active, a Logic 1 on
CFR1<24> enables the auto shaped on-off keying operation.
Toggling the OSK pin high will cause the output scalar to ramp
up from zero scale to the amplitude scale factor at a rate deter-
mined by the amplitude ramp rate. Toggling the OSK pin low
will cause the output to ramp down from the amplitude scale
factor to zero scale at the amplitude ramp rate. See the Shaped
On-Off Keying section for details.

CFR1<23>: Automatic Synchronization Enable Bit

CFR1<23> = 0 (default). The automatic synchronization feature
of multiple AD9954s is inactive.

CFR1<23> = 1. The automatic synchronization feature of mul-
tiple AD9954s is active. The device will synchronize its internal
synchronization clock (SYNC_CLK) to align to the signal pre-
sent on the sync-in input. See the Synchronizing Multiple
AD9954s section for details.

CFR1<22>: Software Manual Synchronization of Multiple
AD9954

CFR1<22> = 0 (default). The manual synchronization feature is
inactive.

AD9954

Rev. 0 | Page 19 of 36

CFR1<22> = 1. The software controlled manual synchroniza-
tion feature is executed. The SYNC_CLK rising edge is
advanced by one SYNC_CLK cycle and this bit is cleared. To
advance the rising edge multiple times, this bit needs to be set
for each advance. See the Synchronizing Multiple AD9954s sec-
tion for details.

CFR1<21>: Linear Frequency Sweep Enable

CFR1<21> = 0 (default). The linear frequency sweep capability
of the AD9954 is inactive.

CFR1<21> = 1, the linear frequency sweep capability of the
AD9954 is enabled. When enabled, either the rising or falling
delta frequency tuning word is applied to the frequency accu-
mulator at the programmed ramp rate, causing the output fre-
quency to ramp up or ramp down, controlled by the Profile 0
input. See the Linear Sweep Mode section for details.

CFR1<20:16>: Not Used

CFR1<15>: Linear Sweep Ramp Rate Load Control Bit

CFR1<15> = 0 (default). The linear sweep ramp rate timer is
loaded only upon timeout (timer = 1) and is not loaded due to
an I/O UPDATE input signal.

CFR1<15> = 1. The linear sweep ramp rate timer is loaded
upon timeout (timer == 1) or at the time of an I/O UPDATE
input signal.

CFR1<14>: Auto Clear Frequency Accumulator Bit

CFR1<14> = 0 (default). The current state of the frequency
accumulator remains unchanged when the delta frequency
word is changed.

CFR1<14> = 1. This bit automatically synchronously clears
(loads 0s into) the frequency accumulator for one cycle upon
reception of an I/O UPDATE signal.

CFR1<13>: Auto-Clear Phase Accumulator Bit

CFR1<13> = 0 (default), the current state of the phase accumu-
lator remains unchanged when the frequency tuning word is
applied.

CFR1<13> = 1. This bit automatically synchronously clears
(loads 0s into) the phase accumulator for one cycle upon recep-
tion of an I/O UPDATE signal.

CFR1<12>: Sine/Cosine Select Bit

CFR1<12> = 0 (default). The angle-to-amplitude conversion
logic employs a COSINE function.

CFR1<12> = 1. The angle-to-amplitude conversion logic
employs a SINE function.

CFR1<11>: Clear Frequency Accumulator

CFR1<11> = 0 (default). The frequency accumulator functions
as normal.

CFR1<11> = 1. The frequency accumulator memory elements
are cleared and held clear until this bit is cleared.

CFR1<10>: Clear Phase Accumulator

CFR1<10> = 0 (default). The phase accumulator functions as
normal.

CFR1<10> = 1. The phase accumulator memory elements are
cleared and held clear until this bit is cleared.

CFR1<9>: SDIO Input Only

CFR1<9> = 0 (default). The SDIO pin has bidirectional opera-
tion (2-wire serial programming mode).

CFR1<9> = 1. The serial data I/O pin (SDIO) is configured as
an input only pin (3-wire serial programming mode).

CFR1<8>: LSB First

CFR1<8> = 0 (default). MSB first format is active.

CFR1<8> = 1.The serial interface accepts serial data in LSB first
format.

CFR1<7>: Digital Power-Down Bit

CFR1<7> = 0 (default). All digital functions and clocks are ac-
tive.

CFR1<7> = 1. All non-IO digital functionality is suspended,
lowering the power significantly.

CFR1<6>: Comparator Power-Down Bit

CFR1<6> = 0 (default). The comparator is enabled for opera-
tion.

CFR1<6> = 1. The comparator is disabled and is in its lowest
power dissipation state.

CFR1<5>: DAC Power-Down Bit

CFR1<5> = 0 (default). The DAC is enabled for operation.

CFR1<5> = 1. The DAC is disabled and is in its lowest power
dissipation state.

CFR1<4>: Clock Input Power-Down Bit

CFR1<4> = 0 (default). The clock input circuitry is enabled for
operation.

CFR1<4> = 1. The clock input circuitry is disabled and the
device is in its lowest power dissipation state.

AD9954

Rev. 0 | Page 20 of 36

CFR1<3>: External Power-Down Mode

CFR1<3> = 0 (default). The external power-down mode
selected is the rapid recovery power-down mode. In this mode,
when the PWRDWNCTL input pin is high, the digital logic and
the DAC digital logic are powered down. The DAC bias cir-
cuitry, comparator, PLL, oscillator, and clock input circuitry are
not powered down.

CFR1<3> = 1. The external power-down mode selected is the
full power-down mode. In this mode, when the PWRDWNCTL
input pin is high, all functions are powered down. This includes
the DAC and PLL, which take a significant amount of time to
power up.

CFR1<2>: Linear Sweep No Dwell Bit

CFR1<2> = 0 (default). The linear sweep no dwell function is
inactive.

CFR1<2> = 1. The linear sweep no dwell function is active. If
CFR1<21>, the linear sweep enable bit, is active and CFR1<2> is
active, the linear sweep no dwell function is activated. See the
Linear Sweep Mode section for details. If CFR1<21> is clear,
this bit is a Don't Care.

CFR1<1>: SYNC_CLK Disable Bit

CFR1<1> = 0 (default). The SYNC_CLK pin is active.

CFR1<1> = 1. The SYNC_CLK pin assumes a static Logic 0
state to keep noise generated by the digital circuitry at a mini-
mum. However, the synchronization circuitry remains active
(internally) to maintain normal device timing.

CFR1<0>: Not Used, Leave at 0

Control Function Register No.2 (CFR2)

The CFR2 is used to control the various functions, features, and
modes of the AD9954, primarily related to the analog sections
of the chip.

CFR2<15:12>: Not Used

CFR2<11>: High Speed Sync Enable Bit

CFR2<11> = 0 (default). The high speed sync enhancement is
off.

CFR2<11> = 1. The high speed sync enhancement is on. This
bit should be set when attempting to use the auto-
synchronization feature for SYNC_CLK inputs beyond 50 MHz,
(200 MSPS SYSCLK). See the Synchronizing Multiple AD9954s
section for details.

CFR2<10>: Hardware Manual Sync Enable Bit

CFR2<10> = 0 (default). The hardware manual sync function is
off.

CFR2<10> = 1. The hardware manual sync function is enabled.
While this bit is set, a rising edge on the SYNC_IN pin will
cause the device to advance the SYNC_CLK rising edge by one
REFCLK cycle. Unlike the software manual sync enable bit, this
bit does not self-clear. Once the hardware manual sync mode is
enabled, it will stay enabled until this bit is cleared. See the
Synchronizing Multiple AD9954s section for details.

CFR2<9>: CRYSTAL OUT Enable Bit

CFR2<9> = 0 (default). The CRYSTAL OUT pin is inactive.

CFR2<9> = 1. The CRYSTAL OUT pin is active. When active,
the crystal oscillator circuitry output drives the CRYSTAL OUT
pin, which can be connected to other devices to produce a refer-
ence frequency. The oscillator will respond to crystals in the
range of 20 MHz to 30 MHz.

CFR2<8>: Not Used

CFR2<7:3>: Reference Clock Multiplier Control Bits

This 5-bit word controls the multiplier value out of the clock-
multiplier (PLL) block. Valid values are decimal 4 to 20 (0Ч04 to
0Ч14). Values entered outside this range will bypass the clock
multiplier. See the Phase-Locked Loop (PLL) section for details.

CFR2<2>: VCO Range Control Bit

This bit is used to control the range setting on the VCO.
When CFR2<2> == 0 (default), the VCO operates in a range of
100 MHz to 250 MHz. When CFR2<2> == 1, the VCO operates
in a range of 250 MHz to 400 MHz.

CFR2<1:0>: Charge Pump Current Control Bits

These bits are used to control the current setting on the charge
pump. The default setting, CFR2<1:0>, sets the charge pump
current to the default value of 75 µA. For each bit added (01, 10,
11) 25 µA of current is added to the charge pump current:
100 µA, 125 µA, and 150 µA.

Other Register Descriptions

Amplitude Scale Factor (ASF)

The ASF register stores the 2-bit auto ramp rate speed value and
the 14-bit amplitude scale factor used in the output shaped key-
ing (OSK) operation. In auto OSK operation, ASF <15:14> tells
the OSK block how many amplitude steps to take for each
increment or decrement. ASF<13:0> sets the maximum value
achievable by the OSK internal multiplier. In manual OSK
mode, ASF<15:14> has no effect. ASF <13:0> provide the output
scale factor directly. If the OSK enable bit is cleared, CFR1<25>
= 0, this register has no effect on device operation.

AD9954

Rev. 0 | Page 21 of 36

Amplitude Ramp Rate (ARR)

The ARR register stores the 8-bit amplitude ramp rate used in
the auto OSK mode. This register programs the rate at which
the amplitude scale factor counter increments or decrements. If
the OSK is set to manual mode, or if OSK enable is cleared, this
register has no effect on device operation.

Frequency Tuning Word 0 (FTW0)

The frequency tuning word is a 32-bit register that controls the
rate of accumulation in the phase accumulator of the DDS core.
Its specific role is dependent on the device mode of operation.

Phase Offset Word (POW)

The phase offset word is a 14-bit register that stores a phase
offset value. This offset value is added to the output of the phase
accumulator to offset the current phase of the output signal.
The exact value of phase offset is given by the following formula

360

POW

When the RAM enable bit is set, CFR1<31> = 1, and the RAM
destination is cleared, CFR1<30> = 0, the RAM supplies the
phase offset word and this register has no effect on device
operation.

Frequency Tuning Word 1 (FTW1)

The frequency tuning word is a 32-bit register that sets the
upper frequency in a linear sweep operation.

Negative and Positive Linear Sweep Control Word (NLSCW,
PLSCW)

Registers 0x07 and 0x08 are multifunctional registers. When the
linear sweep bit CFR1<21> is enabled, Register 0x07 acts as the
negative linear sweep control word (NLSCW) and Register 0x08
acts as the positive linear sweep control word (PLSCW). Each of
the linear sweep control words contains a 32-bit delta frequency
tuning word (FDFTW, RDFTW) and an 8-bit sweep ramp rate
word (FSRRW, RSRRW). The delta frequency tuning words
determine the amount the frequency accumulator will incre-
ment or decrement the resultant tuning word. The sweep ramp
rate words determine the rate at which the accumulator will
increment or decrement, in number of synchronization clock
cycles.

RAM Segment Control Words (RSCW0, RSCW1, RSCW2,
RSCW3)

When the Linear Sweep Enable bit CFR1<21> is clear,
Registers 0x07, 0x08, 0x09, and 0x0A act as the RAM segment
control words for each of the RAM segments. Each of the RAM
segment control words is comprised of a RAM segment address
ramp rate, a final address value, a beginning address value, a
RAM segment mode control, and a No-Dwell Bit.

RAM Segment Address Ramp Rate, RSCW<39:24>

For RAM modes that step through address values, such as
ramping, this 16-bit word defines the number of SYNC_CLK
cycles the RAM controller dwells at each address. A value of 0 is
invalid. Any other value from 1 to 65535 may be used.

RAM Segment Final Address RSCW<9:8>, RSCW<23:16>

This discontinuous 10-bit sequence defines the final address
value for the given RAM segment. The order in which the bits
are listed is the order in which the bits must be written.
RSCW<23>, even though during the write operation is more
significant than RSCW<9>, is only the third MSB of the final
address value. RSCW<9>, even though it comes later in the
RSCW than RSCW<23>, is the MSB of the final address value.

RAM Segment Beginning Address RSCW<3:0>, <15:10>

This discontinuous 10-bit sequence defines the final address
value for the given RAM segment. The order in which the bits
are listed is the order in which the bits must be written.
RSCW<15>, even though during the write operation is more
significant than RSCW<3>, is only the fifth MSB of the final
address value. RSCW<3>, even though it comes later in the
RSCW than RSCW<15>, is the MSB of the final address value.

RAM Segment Mode Control RSCW<7:5>

This 3-bit sequence determines the RAM segment's mode of
operation. There are only five possible RAM modes, so only
values of 05 are valid. See Table 9 to determine the bit combi-
nation for various RAM modes.

RAM Segment No-Dwell Bit RSCW<4>

This bit sets the No-Dwell feature of sweeping profiles. In pro-
files that sweep from a defined beginning to a defined end, the
RAM controller can either dwell at the final address until the
next profile is selected or, when this bit is set, the RAM control-
ler will return to the beginning address and dwell there until the
next profile is selected.

RAM

The AD9954 incorporates a 1024 Ч 32 block of SRAM. The
RAM is a bidirectional single-port. Both read and write opera-
tions from and to the RAM are valid, but they cannot occur
simultaneously. Write operations from the serial I/O port have
precedence, and if an attempt to write to RAM is made during a
read operation, the read operation will be halted. The RAM is
controlled in multiple ways, dictated by the modes of operation
described in the RAM Segment Control Word <7:5> as well as
data in the control function register. Read/write control for the
RAM will be described for each mode supported.

When the RAM enable bit (CFR1<31>) is set, the RAM output
optionally drives the input to the phase accumulator or the
phase offset adder, depending on the state of the RAM destina-

AD9954

Rev. 0 | Page 22 of 36

tion bit (CFR1<30>). If CFR1<30> is a Logic 1, the RAM output
is connected to the phase offset adder and supplies the phase
offset control word(s) for the device. When CFR1<30> is Logic
0 (default condition), the RAM output is connected to the input
of the phase accumulator and supplies the frequency tuning
word(s) for the device. When the RAM output drives the phase
accumulator, the phase offset word (POW, Address 0x05) drives
the phase-offset adder. Similarly, when the RAM output drives
the phase offset adder, the frequency tuning word (FTW,
Address 0x04) drives the phase accumulator. When CFR1<31>
is Logic 0, the RAM is inactive unless being written to via the
serial port. The power-up state of the AD9954 is single-tone
mode, in which the RAM enable bit is inactive. The RAM is
segmented into four unique slices controlled by the Profile<1:0>
input pins.

All RAM writes/reads, unless otherwise specified, are controlled
by the Profile<1:0> input pins and the respective RAM segment
control word. The RAM can be written to during normal opera-
tion, but any I/O operation that commands the RAM to be writ-
ten immediately suspends read operation from the RAM, causing
the current mode of operation to be nonfunctional. This excludes
single-tone mode, as the RAM is not read in this mode.

Writing the RAM is accomplished as follows. After configuring
the desired RAM segment control words, the desired RAM
segment must be selected via the profile select pins PS<1:0>.
During the instruction byte, write the address for the RAM,
0x0B. The serial port and RAM controller will work in conjunc-
tion to determine the width of the profile and the serial port
will accept the defined number of 32-bit words sequentially
from the beginning address to the ending address. Consider the
following example:

The RAM Segment Control Word 1 lists the beginning
RAM address at 256 and the ending address at 511.

PS0 = 1 and PS1 = 0.

The instruction byte is 10001001.

The RAM controller would configure the serial port to expect
256 32-bit words. The first 32 bits would be parsed as a word
and sent to RAM Address 256. The next 32 bits would be parsed
and sent to 257, and so forth, all the way through until the 256
word was sent (grand total of 8192 data bits in this operation).

MODES OF OPERATION

Single-Tone Mode

In single-tone mode, the DDS core uses a single tuning word.
Whatever value is stored in FTW0 is supplied to the phase
accumulator. This value can only be changed manually, which is
done by writing a new value to FTW0 and by issuing an I/O
UPDATE. Phase adjustment is possible through the phase
offset register.

RAM Controlled Modes of Operation

Direct Switch Mode

Direct switch mode enables FSK or PSK modulation. The
AD9954 is programmed for direct switch mode by writing the
RAM enable bit true and programming the RAM segment
mode control bits of each desired profile to Logic 000(b). This
mode simply reads the RAM contents at the RAM segment
beginning address for the current profile. No address ramping is
enabled in direct switch mode.

To perform 4-tone FSK, the user programs each RAM segment
control word for direct switch mode and a unique beginning
address value. In addition, the RAM enable bit is written true,
which enables the RAM, and the RAM destination bit is written
false, setting the RAM output to be the frequency tuning word.
The Profile<1:0> inputs are the 4-tone FSK data inputs. When
the profile is changed, the frequency tuning word stored in the
new profile is loaded into the phase accumulator and used to
increment the currently stored value in a phase continuous
fashion. The phase offset word drives the phase-offset adder.
Two-tone FSK is accomplished by using only one profile pin for
data.

Programming the AD9954 for PSK modulation is similar to
FSK except the RAM destination bit is set to a Logic 1, enabling
the RAM output to drive the phase offset adder. The FTW0
drives the input to the phase accumulator. Toggling the profile
pins changes (modulates) the current phase value. The upper
14 bits of the RAM drive the phase adder (<31:18>).
Bits <17:0> of the RAM output are unused when the RAM des-
tination bit is set. The no dwell bit is a Don't Care in direct
switch mode.

Ramp-Up Mode

Ramp-up mode, in conjunction with the segmented RAM capa-
bility, allows up to four different "sweep profiles" to be pro-
grammed into the AD9954. The AD9954 is programmed for
ramp-up mode by writing the RAM enable bit true and pro-
gramming the RAM mode control bits of each profile to be
used to Logic 001(b). As in all modes that enable the memory,
the RAM destination bit controls whether the RAM output
drives the phase accumulator or the phase offset adder.

Upon starting a sweep (via an I/O UPDATE or change in profile
bits), the RAM address generator loads the RAM segment be-
ginning address bits of the current RSCW, driving the RAM
output from this address, and the ramp rate timer loads the
RAM segment address ramp rate bits. When the ramp rate timer
finishes a cycle, the RAM address generator increments to the
next address, the timer reloads the ramp rate bits and begins a
new countdown cycle. This sequence continues until the RAM
address generator has incremented to an address equal to the
RAM segment final address bits of the current RSCW.

AD9954

Rev. 0 | Page 23 of 36

If the no dwell bit is clear when the RAM address generator
equals the final address, the generator stops incrementing as the
terminal frequency has been reached. The sweep is complete
and does not restart until an I/O UPDATE or change in profile
is detected to enable another sweep from the beginning to the
final RAM address as described above.

If the no dwell bit is set when the RAM address generator
equals the final address, after the next ramp rate timer cycle, the
phase accumulator is cleared. The phase accumulator remains
cleared until another sweep is initiated via an I/O UPDATE
input or change in profile.

Another application for ramp-up mode is nonsymmetrical FSK
modulation. With the RAM configured for two segments, using
the Profile<0> bit as the data input allows nonsymmetrical
ramped FSK.

Bidirectional Ramp Mode

Bidirectional ramp mode allows the AD9954 to offer a symmet-
rical sweep between two frequencies using the Profile<0> signal
as the control input. The AD9954 is programmed for bidirec-
tional ramp mode by writing the RAM enable bit true and the
RAM mode control bits of RSCW0 to Logic 010(b). In bidirec-
tional ramp mode, the Profile<1> input is ignored and the Pro-
file<0> input is the ramp direction indicator. In this mode, the
memory is not segmented and uses only a single beginning and
final address. The address registers that affect the control of the
RAM are located in the RSCW associated with Profile 0.

Upon entering this mode (via an I/O UPDATE or changing
Profile<0>), the RAM address generator loads the RAM seg-
ment beginning address bits of RSCW0 and the ramp rate timer
loads the RAM segment address ramp rate bits. The RAM
drives data from the beginning address, and the ramp rate timer
begins to count down to 1. While operating in this mode, tog-
gling the Profile<0> pin does not cause the device to generate
an internal I/O UPDATE. When the Profile<0> pin is acting as
the ramp direction indicator, any transfer of data from the I/O
buffers to the internal registers can only be initiated by a rising
edge on the I/O UPDATE pin.

RAM address control now is a function of the Profile<0> input.
When the Profile<0> bit is a Logic 1, the RAM address genera-
tor increments to the next address when the ramp rate timer
completes a cycle (and reloads to start the timer again). As in
the ramp-up mode, this sequence continues until the RAM
address generator has incremented to an address equal to the
final address as long as the Profile<0> input remains high. If the
Profile<0> input goes low, the RAM address generator immedi-
ately decrements and the ramp rate timer is reloaded. The RAM
address generator will continue to decrement at the ramp rate
period until the RAM address is equal to the beginning address
as long as the Profile<0> input remains low.

The sequence of ramping up and down is controlled via the
Profile<0> input signal for as long as the part is programmed
into this mode. The no dwell bit is a Don't Care in this mode as
is all data in the RAM segment control words associated with
Profiles 1, 2, and 3. Only the information in the RAM segment
control word for Profile 0 is used to control the RAM in the
bidirectional ramp mode.

Continuous Bidirectional Ramp Mode

Continuous bidirectional ramp mode allows the AD9954 to
offer an automatic symmetrical sweep between two frequencies.
The AD9954 is programmed for continuous bidirectional ramp
mode by writing the RAM enable bit true and the RAM mode
control bits of each profile to be used to Logic 011(b).

Upon entering this mode (via an I/O UPDATE or changing
Profile<1:0>), the RAM address generator loads the RAM seg-
ment beginning address bits of the current RSCW and the ramp
rate timer loads the RAM segment address ramp rate bits. The
RAM drives data from the beginning address, and the ramp rate
timer begins to count down to 1. When the ramp rate timer
completes a cycle, the RAM address generator increments to the
next address, and the timer reloads the ramp rate bits and con-
tinues counting down. This sequence continues until the RAM
address generator has incremented to an address equal to the
RAM segment final address bits of the current RSCW. Upon
reaching this terminal address, the RAM address generator will
decrement in value at the ramp rate until it reaches the RAM
segment beginning address. Upon reaching the beginning ad-
dress, the entire sequence repeats.

The entire sequence repeats for as long as the part is pro-
grammed for this mode. The no dwell bit is a Don't Care in this
mode. In general, this mode is identical in control to the bidi-
rectional ramp mode except the ramp up and down is automatic
(no external control via the Profile<0> input) and switching
profiles is valid. Once in this mode, the address generator ramps
from the beginning address to the final address, then back to
the beginning address at the rate programmed into the ramp
rate register. This mode enables generation of an automatic saw
tooth sweep characteristic.

Continuous Recirculate Mode

Continuous recirculate mode allows the AD9954 to offer
an automatic, continuous unidirectional sweep between two
frequencies. The AD9954 is programmed for continuous
recirculate mode by writing the RAM enable bit true and the RAM
mode control bits of each profile to be used to Logic 100(b).

AD9954

Rev. 0 | Page 24 of 36

completes a cycle, the RAM address generator increments to the
next address, and the timer reloads the ramp rate bits and con-
tinues counting down. This sequence continues until the RAM
address generator has incremented to an address equal to the
RAM segment final address bits of the current RSCW. Upon
reaching this terminal address, the RAM address generator
reloads the RAM segment beginning address bits and the
sequence repeats.

The sequence of circulating through the specified RAM
addresses repeats for as long as the part is programmed for this
mode. The no dwell bit is a Don't Care in this mode.

RAM Controlled Modes of Operation Notes and Summary

Notes:

The user must ensure that the beginning address is lower
than the final address.

Changing profiles or issuing an I/O UPDATE automatically
terminates the current sweep and starts the next sweep.

Setting the RAM destination bit true such that the RAM
output drives the phase offset adder is valid. While the
above discussion describes a frequency sweep, a phase
sweep operation is also available.

The AD9954 offers five modes of RAM controlled operation
(see Table 9).

Table 9. RAM Modes of Operation

RSCW<7:5>
(Binary)

Mode

Notes

000 Direct

Switch

No Sweeping, Profiles
Valid, No Dwell Invalid

001 Ramp

Sweeping, Profiles Valid,
No Dwell Valid

010

Bidirectional
Ramp

Sweeping, Profile <0> Is a
Direction Control Bit, No
Dwell Invalid

011

Continuous
Bidirectional
Ramp

Sweeping, Profiles Valid,
No Dwell Invalid

100

Continuous
Recirculate

Sweeping, Profiles Valid,
No Dwell Invalid

101, 110, 111

Open

Invalid Mode--Default To
Direct Switch

Internal Profile Control

The AD9954 offers a mode in which a composite frequency
sweep can be built, for which the timing control is software
programmable. The internal profile control capability disen-
gages the Profile<1:0> pins and enables the AD9954 to take
control of switching between profiles. Modes are defined that
allow continuous or single burst profile switches for three com-
binations of profile selection bits. These are listed in Table 10.

When any of the CFR1<29:27> bits are active, the
internal profile control mode is engaged. Internal profile control
is only valid when the device is operating in RAM mode. There
is no internal profile control for linear sweeping operations.

When the internal profile control mode is engaged, the RAM
segment mode control bits are Don't Care and the device oper-
ates all profiles as if these mode control bits were programmed
for ramp-up mode. Switching between profiles occurs when the
RAM address generator has exhausted the memory contents for
the current profile.

Table 10. Internal Profile Control

CFR1<29:27>
(Binary)

Mode Description

000

Internal Control Inactive

001

Internal Control Active, Single Burst, Activate
Profile 0, Then 1, Then Stop

010

Internal Control Active, Single Burst, Activate
Profile 0, Then 1, Then 2, Then Stop

011

Internal Control Active, Single Burst, Activate
Profile 0, Then 1, Then 2, Then 3, Then Stop

100

Internal Control Active, Continuous, Activate
Profile 0, Then 1, Then Loop Starting 0

101

Internal Control Active, Continuous, Activate
Profile 0, Then 1, Then 2, Then Loop Starting 0

110

Internal Control Active, Continuous, Activate
Profile 0, Then 1, Then 2, Then 3, Then Loop
Starting 0

111 Invalid

A single burst mode is one in which the composite sweep is
executed once. For example, assume the device is programmed
for ramp-up mode and the CFR1<29:27> bits are written to
Logic 010(b). Upon receiving an I/O UPDATE, the internal
control logic signals the device to begin executing the ramp-up
mode sequence for Profile 0. Upon reaching the RAM segment
final address value for Profile 0, the device automatically
switches to Profile 1 and begins executing that ramp-up
sequence. Upon reaching the RAM segment final address value
for Profile 1, the device automatically switches to Profile 2 and
begins executing that ramp-up sequence. When the RAM seg-
ment final address value for Profile 2 is reached, the sequence is
over and the composite sweep has completed. Issuing another
I/O UPDATE restarts the burst process.

A continuous internal profile control mode is one in which the
composite sweep is continuously executed for as long as the
device is programmed into that mode. Using the example above,
except programming the CFR1<29:27> bits to Logic 101(b), the
operation would be identical until the RAM segment final
address value for Profile 2 is reached. At this point, instead of
stopping the sequence, it repeats, starting with Profile 0.

AD9954

Rev. 0 | Page 25 of 36

Linear Sweep Mode

The AD9954 is placed in linear sweep mode by setting the lin-
ear sweep enable bit CR1<21>. When in linear sweep mode, the
AD9954 output frequency will ramp up from a starting fre-
quency, programmed by FTW0 to a finishing frequency FTW1,
or down from FTW1 to FTW0. The delta frequency tuning
words and the ramp rate word determine the rate at which this
ramping takes place. The linear sweep no-dwell bit CFR1<2>
controls the behavior of the device upon reaching the terminal
frequency. The 32-bit rising delta frequency tuning word
(RDFTW) increments the frequency accumulator when ramp-
ing up from FTW0 to FTW1. The 8-bit rising sweep ramp rate
word (RSRRW) controls the rate at which the frequency accu-
mulator is incremented. The 32-bit falling delta frequency tun-
ing word (FDFTW) decrements the accumulator when ramping
down from FTW1 to FTW0. The 8-bit falling sweep ramp rate
word (FSRRW) determines the rate at which the accumulator is
decremented.

The PS<0> pin controls the direction of the sweep, rising to
FTW1 or falling to FTW0. Upon reaching the destination fre-
quency, the AD9954 linear sweep function will either hold at the
destination frequency until the state on the PS<0> pin is
changed or immediately return to the initial frequency, FTW0,
depending on the state of the linear sweep no-dwell bit
CFR1<02>. While operating in linear sweep mode, toggling the
Profile<0> pin does not cause the device to generate an internal
I/O UPDATE. When the PS<0> pin is acting as the sweep direc-
tion indicator, any transfer of data from the I/O buffers to the
internal registers can only be initiated by a rising edge on the
I/O UPDATE pin.

The linear sweep function of the AD9954 requires the lowest
frequency to be loaded into the FTW0 register and the highest
frequency into the FTW1 register. For piece-wise, nonlinear
frequency transitions, it is necessary to reprogram the registers
while the frequency transition is in progress to affect the desired
response. Figure 20 demonstrates a typical frequency ramping
operation. After a reset, the device will initially be in single tone
mode. The programming steps to operate in linear sweep mode
are

Profile inputs at 00.

Set the linear sweep enable bit (CFR1<21> = 1) and
set or clear the linear sweep no-dwell bit (CFR1<2> =
{0,1}) as desired.

Program the rising and falling delta frequency tuning
words and ramp rate values.

Program the lower and higher output frequencies into
the FTW0 and FTW1 registers, respectively.

Apply an I/O UPDATE to move this data into the reg-
isters (the output frequency will be FTW0).

Change the PS<0> input as desired to sweep between
the lower to higher frequency and back.

Figure 20 shows that the device initially powers up in single
tone mode. The profile inputs are low, which places the FTW0
input to the phase accumulator. The user then configures the
device as desired by writing the rising and falling delta
frequency tuning words and ramp rates, as well as the linear
sweep enable bit, via the serial port (Point A in Figure 20). In this
example, the linear sweep no-dwell bit is cleared (CFR1<2> = 0).

General Operation of Linear Sweep Capability

In linear sweep mode, the PS<1> pin must be tied to Logic 0.
With linear sweep mode active, when the PS<0> pin transitions
from low to high, the RDFTW is applied to the input of the
frequency accumulator and the RSRR register is loaded into the
sweep rate timer. The sweep rate timer counts down from an
initial value to one, at which point the frequency accumulator is
allowed to accumulate the input. This accumulation of the
RDFTW at the rate given by the ramp rate (RSRR) continues
until the output of the frequency adder is equal to the FTW1
register value. At this time the accumulation is stopped, causing
the AD9954 to output the frequency given by the FTW1. The
output remains at FTW1 for as long as the PS<0> pin remains
at Logic 1.

When the PS<0> pin transitions from high to low, the
negated FDFTW is applied to the input of the frequency accu-
mulator and the FSRR register is loaded into the sweep rate
timer. Each time the timer counts down to one, the frequency
accumulator is allowed to accumulate the input. This accumula-
tion of the negated FDFTW at the rate given by the ramp rate
(FSRR) continues until the output of the frequency adder is
equal to the FTW0 register value. At this time the accumulation
is stopped, causing the AD9954 to output the frequency given
by the FTW0. The output remains at FTW0 for as long as the
PS<0> pin remains at Logic 0.

AD9954

Rev. 0 | Page 26 of 36

03374-0-003

FTW0

SINGLETONE

MODE

LINEAR SWEEP MODE

AT POINT A: LOAD RISING RAMP RATE REGISTER, APPLY RISING DFTW.
AT POINT B: LOAD FALLING RAMP RATE REGISTER, APPLY FALLING DFTW.

PS<0> = 1

PS<0> = 0

TIME

FTW1

OUT

Figure 20. Linear Sweep Frequency Plan

03374-0-004

FTW0

SINGLETONE

MODE

LINEAR SWEEP MODE ENABLENO DWELL BIT SET

FTW1

OUT

TIME

PS<0> = 1 PS<0> = 0

PS<0> = 0

PS<0> = 1

PS<0> = 0

Figure 21. Linear Sweep Using No Dwell Frequency Plan

Linear Sweep No Dwell Feature

The linear sweep function can be operated with a no dwell fea-
ture. If the linear sweep no dwell bit is set, CFR1<2> = 1, the
rising sweep is started in an identical manner to the non-no
dwell linear sweep mode. Upon detecting a rising edge on the
PS<0> input pin, the rising sweep action is initiated. The fre-
quency continues to sweep up at the rate set by the rising sweep
ramp rate at the resolution set by the rising delta frequency
tuning word until it reaches the terminal frequency. Upon
reaching the terminal frequency, the output frequency immedi-
ately returns to the starting frequency and remains at the start-
ing frequency until the device detects a subsequent rising edge
on the PS<0> pin. Figure 21 is an example of the linear sweep

mode operation when the linear sweep no dwell bit is set. The
points labeled A indicate where a rising edge on PS0 is detected;
the points labeled B indicate where the AD9954 has determined
F

OUT

has reached the terminal frequency and automatically

returns to the starting frequency. Note that in this mode, each
sweep will require a separate rising edge on the Profile <0> pin.
Linear sweeps using the no-dwell bit can only be swept from
FTW0 to FTW1 using the positive linear sweep control word.
Toggling the PS<0> from 1 to 0 will not initiate a falling sweep
when the no dwell bit is set, nor will it interrupt a positive
sweep already underway.

AD9954

Rev. 0 | Page 27 of 36

Programming the Ramp Rate Timer

The linear sweep ramp rate timer is a loadable down counter
that, when enabled, continuously counts down from the loaded
value to a count of 1. When in a rising transition, the loaded
value is the RSRRW; when in a falling transition, the value is the
FSRRW. When the ramp rate timer equals 1, the proper
RFDTW or FDFTW is loaded and the counter begins counting
down to 1 again. This load and count down operation continues
for as long as the timer is enabled, unless the timer is forced to
load before reaching a count of 1.

The ramp timer can be loaded before reaching a count of 1 by
three methods.

Method one is by changing the PS<0> input pin. When the
PS<0> input pin changes from a Logic 0 to a Logic 1, the
RSRRW value is loaded into the ramp rate timer, which then
proceeds to count down as normal. When the Profile<0> input
pin changes from a Logic 1 to a Logic 0, the FSRR value is
loaded into the ramp rate timer, which then proceeds to count
down as normal.

The second method in which the sweep ramp rate timer can be
loaded before reaching a count of 1 is if the CFR1<15> bit is set
and an I/O UPDATE is issued. If sweep is enabled and
CFR1<15> is set, the ramp rate timer loads the value deter-
mined by the Profile<0> pin every time an I/O UPDATE is
issued. If the Profile<0> pin is low (high), the ramp rate timer
loads the FSRRW (RSRRW).

The last method in which the sweep ramp rate timer can be
loaded before reaching a count of 1 is going from the inactive
linear sweep mode to the active linear sweep mode. That is
when the sweep enable bit is being set. The ramp rate loaded is a
function of the Profile<0> input pin.

Continuous and "Clear and Release" Frequency and Phase
Accumulator Clear Functions

The AD9954 allows for a programmable continuous zeroing of
the frequency sweep logic and the phase accumulator as well as
a clear and release or automatic zeroing function. Each feature is
individually controlled via Bits CFR1. CFR1<14> is the auto-
matic clear frequency accumulator bit and CFR1<13> is the
automatic clear phase accumulator bit. The continuous clear
bits are located in CFR1<11:10>, where CFR1<11> clears the
frequency accumulator and CFR1<10> clears the phase accu-
mulator.

Continuous Clear Bits

The continuous clear bits are simply static control signals that,
when active high, hold the respective accumulator at zero for
the entire time the bit is active. When the bit goes low, inactive,
the respective accumulator is allowed to operate.

Clear and Release Function

The auto clear frequency accumulator bit, when set, clears
and releases the frequency accumulator upon receiving an I/O
UPDATE signal or change in one of the profile pins. The auto
clear phase accumulator, when set, clears and releases the phase
accumulator upon receiving an I/O UPDATE or change on one
of the profile pins. The automatic clearing function is repeated
for every subsequent I/O UPDATE or change on one of the
profile pins until the appropriate auto-clear control bit is
cleared.

Note that these bits are programmed independently and do not
have to be active at the same time. For example, one accumula-
tor may be using the clear and release function while the other
is continuously cleared.

Programming AD9954 Features

Phase Offset Control

A 14-bit phase offset () may be added to the output of the
phase accumulator by means of the control registers. This fea-
ture provides the user with three different methods of phase
control.

The first method is a static phase adjustment, where a fixed
phase offset is loaded into the appropriate phase offset register
and left unchanged. The result is that the output signal is offset
by a constant angle relative to the nominal signal. This allows
the user to phase align the DDS output with some external sig-
nal, if necessary.

The second method of phase control is where the user regularly
updates the phase offset register via the I/O port. By properly
modifying the phase offset as a function of time, the user can
implement a phase modulated output signal. However, both the
speed of the I/O port and the frequency of SYSCLK limit the
rate at which phase modulation can be performed.

The third method of phase control involves the RAM and the
profile input pins. The AD9954 can be configured such that the
RAM drives the phase adjust circuitry. The user can control the
phase offset via the RAM in an identical manner allowed for
frequency sweeping. See the RAM Controlled Modes of Opera-
tion and the Linear Sweep Mode sections for details.

Shaped On-Off Keying

The shaped on-off keying function of the AD9954 allows the
user to control the ramp-up and ramp-down time of an on-off
emission from the DAC. This function is used in burst trans-
missions of digital data to reduce the adverse spectral impact of
short, abrupt bursts of data.

Auto and manual shaped on-off keying modes are supported.
The auto mode generates a linear scale factor at a rate deter-
mined by the amplitude ramp rate (ARR) register controlled by
an external pin (OSK). Manual mode allows the user to directly

AD9954

Rev. 0 | Page 28 of 36

control the output amplitude by writing the scale factor value
into the amplitude scale factor (ASF) register.

The shaped on-off keying function may be bypassed (disabled)
by clearing the OSK enable bit (CFR1<25> = 0).

The modes are controlled by two bits located in the most sig-
nificant byte of the control function register (CFR). CFR1<25>
is the shaped on-off keying enable bit. When CFR1<25> is set,
the output scaling function is enabled; CFR1<25> bypasses the
function. CFR1<24> is the internal shaped on-off keying active
bit. When CFR1<24> is set, internal shaped on-off keying mode
is active; CFR1<24> cleared is external shaped on-off keying
mode active. CFR1<24> is a Don't Care if the shaped on-off
keying enable bit (CFR1<25>) is cleared. The power up condi-
tion is shaped on-off keying disabled (CFR1<25> = 0).
Figure 22 shows the block diagram of the OSK circuitry.

AUTO Shaped On-Off Keying Mode Operation

The auto shaped on-off keying mode is active when CFR1<25>
and CFR1<24> are set. When auto shaped on-off keying mode
is enabled, a single scale factor is internally generated and
applied to the multiplier input for scaling the output of the DDS
core block (see Figure 22). The scale factor is the output of a
14-bit counter that increments/decrements at a rate determined
by the contents of the 8-bit output ramp rate register. The scale
factor increases if the OSK pin is high and decreases if the OSK
pin is low. The scale factor is an unsigned value such that all 0s
multiply the DDS core output by 0 (decimal) and 0x3FFF mul-
tiplies the DDS core output by 16383 (decimal).

For those users who use the full amplitude (14-bits) but need
fast ramp rates, the internally generated scale factor step size
is controlled via the ASF<15:14> bits. Table 11 describes the
increment/decrement step size of the internally generated scale
factor per the ASF<15:14> bits.

A special feature of this mode is that the maximum output
amplitude allowed is limited by the contents of the amplitude
scale factor register. This allows the user to ramp to a value less
than full scale.

Table 11. Auto-Scale Factor Internal Step Size

ASF<15:14> (Binary)

Increment/Decrement Size

00 1
01 2
10 4
11 8

OSK Ramp Rate Timer

The OSK ramp rate timer is a loadable down counter, which
generates the clock signal to the 14-bit counter that generates
the internal scale factor. The ramp rate timer is loaded with the
value of the ASFR every time the counter reaches 1 (decimal).
This load and countdown operation continues for as long as the
timer is enabled, unless the timer is forced to load before reach-
ing a count of 1.

If the load OSK timer bit (CFR1<26>) is set, the ramp rate timer
is loaded upon an I/O UPDATE, upon a change in profile input,
or upon reaching a value of 1. The ramp timer can be loaded
before reaching a count of 1 by three methods.

Method one is by changing the OSK input pin. When the OSK
input pin changes state, the ASFR value is loaded into the ramp
rate timer, which then proceeds to count down as normal.

The second method in which the sweep ramp rate timer can be
loaded before reaching a count of 1 is if the load OSK timer bit
(CFR1<26>) is set and an I/O UPDATE (or change in profile) is
issued.

The last method in which the sweep ramp rate timer can be
loaded before reaching a count of 1 is when going from the
inactive auto shaped on-off keying mode to the active auto
shaped on-off keying mode. That is, when the sweep enable bit
is being set.

03374-0-005

OSK PIN

LOAD OSK TIMER

CFR1<26>

SYNC_CLK

AUTO DESK

EMABLE

CFR1<24>

TO DAC

AUTO SCALE

FACTOR GENERATOR

RAMP RATE TIMER

CLOCK

DDS CORE

OSK ENABLE

CFR<25>

AMPLITUDE SCALE
FACTOR REGISTER

(ASF)

HOLD

INC/DEC ENABLE

OUT

COS(X)

AMPLITUDE RAMP

RATE REGISTER

(ASF)

UP/DN

DATA

LOAD

Figure 22. On-Off Shaped Keying, Block Diagram

AD9954

Rev. 0 | Page 29 of 36

External Shaped On-Off Keying Mode Operation

The external Shaped On-Off Keying mode is enabled by writing
CFR1<25> to a logic 1 AND writing CFR1<24> to a Logic 0.
When configured for external Shaped On-Off Keying, the
content of the ASFR becomes the scale factor for the data path.
The scale factors are synchronized to SYNC_CLK via the I/O
UPDATE functionality.

Synchronization; Register Updates (I/O UPDATE)

Functionality of the SYNC_CLK and I/O UPDATE

Data into the AD9954 is synchronous to the SYNC_CLK signal
(supplied externally to the user on the SYNC_CLK pin). The
I/O UPDATE pin is sampled on the rising edge of the
SYNC_CLK.

Internally, SYSCLK is fed to a divide-by-4 frequency divider to
produce the SYNC_CLK signal. The SYNC_CLK signal is pro-
vided to the user on the SYNC_CLK pin. This enables synchro-
nization of external hardware with the device's internal clocks.
This is accomplished by forcing any external hardware to obtain
its timing from SYNC_CLK. The I/O UPDATE signal coupled

with SYNC_CLK is used to transfer internal buffer contents
into the control registers of the device. The combination of the
SYNC_CLK and I/O UPDATE pins provide the user with
constant latency relative to SYSCLK and also ensures phase
continuity of the analog output signal when a new tuning word
or phase offset value is asserted. Figure 23 demonstrates an I/O
UPDATE timing cycle and synchronization.

Notes to synchronization logic:

The I/O UPDATE signal is edge detected to generate a
single rising edge clock signal that drives the register bank
flops. The I/O UPDATE signal has no constraints on duty
cycle. The minimum low time on I/O UPDATE is one
SYNC_CLK clock cycle.

The I/O UPDATE pin is set up and held around the rising
edge of SYNC_CLK and has zero hold time and 4 ns setup
time.

03374-0-006

SYSCLK

SDI

SYNC_CLK

DISABLE

SCLK

TO CORE LOGIC

OSK

PROFILE<1:0>

I/O UPDATE

ч 4

SYNC_CLK

GATING

EDGE

DETECTION

LOGIC

REGISTER

MEMORY

I/O BUFFER

LATCHES

Figure 23. I/O Synchronization Block Diagram

AD9954

Rev. 0 | Page 30 of 36

SYNC_CLK

SYSCLK

DATA 2

DATA 3

DATA 1

DATA IN

REGISTERS

DATA IN

I/O BUFFERS

DATA 1

DATA 2

DATA 3

I/O UPDATE

THE DEVICE REGISTERS AN I/O UPDATE AT POINT A. THE DATA IS TRANSFERRED FROM THE ASYNCHRONOUSLY LOADED I/O BUFFERS AT POINT B.

03374-0-007

Figure 24. I/O Synchronization Timing Diagram

Synchronizing Multiple AD9954s

The AD9954 product allows easy synchronization of multiple
AD9954s. There are three modes of synchronization available
to the user: an automatic synchronization mode, a software
controlled manual synchronization mode, and a hardware
controlled manual synchronization mode. In all cases, when a
user wants to synchronize two or more devices, the following
considerations must be observed. First, all units must share a
common clock source. Trace lengths and path impedance of the
clock tree must be designed to keep the phase delay of the dif-
ferent clock branches as closely matched as possible. Second, the
I/O UPDATE signal's rising edge must be provided synchro-
nously to all devices in the system. Finally, regardless of the
internal synchronization method used, the DVDD_I/O supply
should be set to 3.3 V for all devices that are to be synchronized.
AVDD and DVDD should be left at 1.8 V.

In automatic synchronization mode, one device is chosen as a
master, the other device(s) will be slaved to this master. When
configured in this mode, all the slaves will automatically syn-
chronize their internal clocks to the SYNC_CLK output signal
of the master device. To enter automatic synchronization mode,
set the slave device's automatic synchronization bit (CFR1<23>
= 1). Connect the SYNC_IN input(s) to the master SYNC_CLK
output. The slave device will continuously update the phase
relationship of its SYNC_CLK until it is in phase with the
SYNC_IN input, which is the SYNC_CLK of the master device.
When attempting to synchronize devices running at SYSCLK
speeds beyond 250 MSPS, the high speed sync enhancement
enable bit should be set (CFR2<11> = 1).

In software manual synchronization mode, the user forces the
device to advance the SYNC_CLK rising edge one SYSCLK
cycle (1/4 SYNC_CLK period). To activate the manual
synchronization mode, set the slave device's software manual
synchronization bit (CFR1<22> = 1). The bit (CFR1<22>) will be
immediately cleared. To advance the rising edge of the SYNC_CLK
multiple times, this bit will need to be set multiple times.

In hardware manual synchronization mode, the SYNC_IN
input pin is configured such that it will now advance the rising

edge of the SYNC_CLK signal each time the device detects a
rising edge on the SYNC_IN pin. To put the device into hard-
ware manual synchronization mode, set the hardware manual
synchronization bit (CFR2<10> = 1). Unlike the software man-
ual synchronization bit, this bit does not self-clear. Once the
hardware manual synchronization mode is enabled, all rising
edges detected on the SYNC_IN input will cause the device to
advance the rising edge of the SYNC_CLK by one SYSCLK
cycle until this enable bit is cleared (CFR2<10> = 0).

Using a Single Crystal to Drive Multiple AD9954 Clock
Inputs

The AD9954 crystal oscillator output signal is available on the
CRYSTAL OUT pin, enabling one crystal to drive multiple
AD9954s. In order to drive multiple AD9954s with one crystal,
the CRYSTAL OUT pin of the AD9954 using the external crys-
tal should be connected to the REFCLK input of the other
AD9954.

The CRYSTAL OUT pin is static until the CFR2<1> bit is set,
enabling the output. The drive strength of the CRYSTAL OUT
pin is typically very low, so this signal should be buffered prior
to using it to drive any loads.

SERIAL PORT OPERATION

With the AD9954, the instruction byte specifies read/write
operation and register address. Serial operations on the AD9954
occur only at the register level, not the byte level. For the
AD9954, the serial port controller recognizes the instruction
byte register address and automatically generates the proper
register byte address. In addition, the controller expects that all
bytes of that register will be accessed. It is a requirement that all
bytes of a register be accessed during serial I/O operations, with
one exception. The IOSYNC function can be used to abort an
I/O operation, thereby allowing less than all bytes to be ac-
cessed.

There are two phases to a communication cycle with the
AD9954. Phase 1 is the instruction cycle, which is the writing of
an instruction byte into the AD9954, coincident with the first

AD9954

Rev. 0 | Page 31 of 36

eight SCLK rising edges. The instruction byte provides the
AD9954 serial port controller with information regarding the
data transfer cycle, which is Phase 2 of the communication cycle.
The Phase 1 instruction byte defines whether the upcoming data
transfer is read or write and the serial address of the register
being accessed. [Note that the serial address of the register
being accessed is NOT the same address as the bytes to be
written. See the Example Operation section for details].

The first eight SCLK rising edges of each communication cycle
are used to write the instruction byte into the AD9954. The
remaining SCLK edges are for Phase 2 of the communication
cycle. Phase 2 is the actual data transfer between the AD9954
and the system controller. The number of bytes transferred
during Phase 2 of the communication cycle is a function of the

register being accessed. For example, when accessing the Control
Function Register 2, which is three bytes wide, Phase 2 requires that
three bytes be transferred. If accessing the frequency tuning word,
which is four bytes wide, Phase 2 requires that four bytes be
transferred. After transferring all data bytes per the instruction,
the communication cycle is completed.

At the completion of any communication cycle, the AD9954
serial port controller expects the next eight rising SCLK edges
to be the instruction byte of the next communication cycle. All
data input to the AD9954 is registered on the rising edge of
SCLK. All data is driven out of the AD9954 on the falling edge
of SCLK. Figure 25 through Figure 28 are useful in understand-
ing the general operation of the AD9954 serial port

03374-0-008

INSTRUCTION CYCLE

SCLK

SDIO

DATA TRANSFER CYCLE

Figure 25. Serial Port Write TimingClock Stall Low

03374-0-009

DON'T CARE

INSTRUCTION CYCLE

SCLK

SDIO

DATA TRANSFER CYCLE

O 5

O 4

O 3

O 2

O 1

O 0

O 7

O 6

SDO

Figure 26. 3-Wire Serial Port Read TimingClock Stall Low

03374-0-010

INSTRUCTION CYCLE

SCLK

SDIO

DATA TRANSFER CYCLE

Figure 27. Serial Port Write TimingClock Stall High

03374-0-011

O 5

O 4

O 3

O 2

O 1

O 0

O 7

O 6

INSTRUCTION CYCLE

SCLK

SDIO

DATA TRANSFER CYCLE

Figure 28. 2-Wire Serial Port Read Timing--Clock Stall High

AD9954

Rev. 0 | Page 32 of 36

INSTRUCTION BYTE

The instruction byte contains the following information:

Table 12.

MSB

D6 D5 D4 D3 D2 D1 LSB

R/Wb

X X A4 A3 A2 A1 A0

R/Wb--Bit 7 of the instruction byte determines whether a read
or write data transfer will occur after the instruction byte write.
Logic High indicates read operation. Logic 0 indicates a write
operation.

X, X--Bits 6 and 5 of the instruction byte are Don't Care.

A4, A3, A2, A1, A0--Bits 4, 3, 2, 1, 0 of the instruction byte
determine which register is accessed during the data transfer
portion of the communications cycle.

SERIAL INTERFACE PORT PIN DESCRIPTION

SCLK--Serial Clock. The serial clock pin is used to synchronize
data to and from the AD9954 and to run the internal state ma-
chines. SCLK maximum frequency is 25 MHz.

CSB--Chip Select Bar. CSB is active low input that allows more
than one device on the same serial communications line. The
SDO and SDIO pins will go to a high impedance state when this
input is high. If driven high during any communications cycle,
that cycle is suspended until CS is reactivated low. Chip select
can be tied low in systems that maintain control of SCLK.

SDIO -- Serial Data I/O. Data is always written into the
AD9954 on this pin. However, this pin can be used as a
bidirectional data line. Bit 7 of Register Address 0x0 controls
the configuration of this pin. The default is Logic 0, which
configures the SDIO pin as bidirectional.

SDO--Serial Data Out. Data is read from this pin for protocols
that use separate lines for transmitting and receiving data. In the
case where the AD9954 operates in a single bidirectional I/O
mode, this pin does not output data and is set to a high imped-
ance state.

IOSYNC--It synchronizes the I/O port state machines without
affecting the addressable registers contents. An active high input
on the IOSYNC pin causes the current communication cycle to
abort. After IOSYNC returns low (Logic 0), another communi-
cation cycle may begin, starting with the instruction byte write.

MSB/LSB TRANSFERS

The AD9954 serial port can support both most significant bit
(MSB) first or least significant bit (LSB) first data formats. This
functionality is controlled by the Control Register 0x00 <8> bit.
The default value of Control Register 0x00 <8> is low (MSB
first). When Control Register 0x00 <8> is set high, the AD9954
serial port is in LSB first format. The instruction byte must be

written in the format indicated by Control Register 0x00 <8>. If
the AD9954 is in LSB first mode, the instruction byte must be
written from least significant bit to most significant bit.

For MSB first operation, the serial port controller will generate
the most significant byte (of the specified register) address first
followed by the next lesser significant byte addresses until the
I/O operation is complete. All data written to (read from) the
AD9954 must be (will be) in MSB first order. If the LSB mode is
active, the serial port controller will generate the least signifi-
cant byte address first followed by the next greater significant
byte addresses until the I/O operation is complete. All data writ-
ten to (read from) the AD9954 must be (will be) in LSB first
order.

Example Operation

To write the amplitude scale factor register in MSB first format,
apply an instruction byte of 0x02 (serial address is 00010(b)).
From this instruction, the internal controller will generate an
internal byte address of 0x07 (see the register map) for the first
data byte written and an internal address of 0x08 for the next
byte written. Since the amplitude scale factor register is two
bytes wide, this ends the communication cycle.

To write the amplitude scale factor register in LSB first format,
apply an instruction byte of 0x40. From this instruction, the
internal controller will generate an internal byte address of 0x08
(see the register map) for the first data byte written and an in-
ternal address of 0x07for the next byte written. Since the ampli-
tude scale factor register is two bytes wide, this ends the com-
munication cycle.

RAM I/O VIA SERIAL PORT

Accessing the RAM via the serial port is identical to any other
serial I/O operation except that the number of bytes transferred
is determined by the address space between the beginning
address and the final address as specified in the current RAM
segment control word (RSCW). The final address describes the
most significant word address for all I/O transfers and the
beginning address specifies the least significant address.

RAM I/O supports MSB/LSB first operation. When in MSB first
mode, the first data byte will be for the most significant byte of
the memory address described by the final address with the
remaining three bytes making up the lesser significant bytes of
that address. The remaining bytes come in most significant to
least significant, destined for RAM addresses generated in
descending order until the final four bytes are written into the

AD9954

Rev. 0 | Page 33 of 36

The system must maintain synchronization with the
AD9954 or the internal control logic will not be able to
recognize further instructions. For example, if the system
sends an instruction byte that describes writing a 2-byte
register, then pulses the SCLK pin for a 3-byte write (24
additional SCLK rising edges), communication synchroni-
zation is lost. In this case, the first 16 SCLK rising edges
after the instruction cycle will properly write the first two
data bytes into the AD9954, but the next eight rising SCLK
edges are interpreted as the next instruction byte not the
final byte of the previous communication cycle. In the case
where synchronization is lost between the system and the
AD9954, the IOSYNC pin provides a means to re-establish
synchronization without re-initializing the entire chip. The
IOSYNC pin enables the user to reset the AD9954 state
machine to accept the next eight SCLK rising edges to be
coincident with the instruction phase of a new communi-
cation cycle. By applying and removing a high signal to the
IOSYNC pin, the AD9954 is set to once again begin per-
forming the communication cycle in synchronization with
the system. Any information that had been written to the
AD9954 registers during a valid communication cycle
prior to loss of synchronization will remain intact.

address specified as the beginning address. When in LSB first
mode, the first data byte will be for the least significant byte
of the memory (specified by the beginning address) with the
remaining three bytes making up the greater significant bytes of
that address. The remaining bytes come in least significant to
most significant, destined for RAM addresses generated in
ascending order until the final four bytes are written into the
memory address described by the final address. Of course, the
bit order for all bytes is least significant to most significant first
when the LSB first bit is set. When the LSB first bit is cleared
(default), the bit order for all bytes is most significant to least
significant.

The RAM uses serial address 01011(b), so the instruction byte
to write the RAM is 0Ч0B, in MSB first notation. As mentioned
above, the RAM addresses generated are specified by the begin-
ning and final address of the RSCW currently selected by the
Profile<1:0> pins.

Notes on serial port operation:

The AD9954 serial port configuration bits reside in Bits 8
and 9 of CFR1 (Address 0x00). The configuration changes
immediately upon writing to this register. For multibyte
transfers, writing to this register may occur during the
middle of a communication cycle. Care must be taken to
compensate for this new configuration for the remainder
of the current communication cycle.

Reading profile registers requires that the profile select pins
(Profile<1:0>) be configured to select the desired register
bank. When reading a register that resides in one of the
profiles, the register address acts as an offset to select one
of the registers among the group of registers defined by the
profile, while the profile select pins select the appropriate
register group.

Power-Down Functions of the AD9954

The AD9954 supports an externally controlled or hardware
power-down feature as well as the more common software pro-
grammable power-down bits found in previous ADI DDS products.

The software control power-down allows the DAC, comparator,
PLL, input clock circuitry, and the digital logic to be individu-
ally power down via unique control bits (CFR1<7:4>). With the
exception of CFR1<6>, these bits are not active when the exter-
nally controlled power-down pin (PWRDWNCTL) is high.
External power-down control is supported on the AD9954 via
the PWRDWNCTL input pin. When the PWRDWNCTL input
pin is high, the AD9954 will enter a power-down mode based
on the CFR1<3> bit. When the PWRDWNCTL input pin is low,
the external power-down control is inactive.

When the CFR1<3> bit is 0, and the PWRDWNCTL input pin
is high, the AD9954 is put into a fast recovery power-down
mode. In this mode, the digital logic and the DAC digital logic
are powered down. The DAC bias circuitry, comparator, PLL,
oscillator, and clock input circuitry is NOT powered down. The
comparator can be powered down by setting the comparator
power-down bit, CFR1<6> = 1.

When the CFR1<3> bit is high, and the PWRDWNCTL input
pin is high, the AD9954 is put into the full power-down mode.
In this mode, all functions are powered down. This includes the
DAC and PLL, which take a significant amount of time to
power up.

When the PWRDWNCTL input pin is high, the individual
power-down bits (CFR1<7>, <5:4>) are invalid (Don't Care)
and unused; however, the comparator power-down bit,
CFR1<6>, will continue to control the power-down of the com-
parator. When the PWRDWNCTL input pin is low, the individual
power-down bits control the power-down modes of operation.

Note that the power-down signals are all designed such that a
Logic 1 indicates the low power mode and a Logic 0 indicates
the active or powered up mode.

AD9954

Rev. 0 | Page 34 of 36

Table 13 indicates the logic level for each power-down bit that
drives out of the AD9954 core logic to the analog section and
the digital clock generation section of the chip for the external
power-down operation.

Layout Considerations

For the best performance, the following layout guidelines
should be observed. Always provide the analog power supply
(AVDD) and the digital power supply (DVDD) on separate
supplies, even if just from two different voltage regulators
driven by a common supply. Likewise, the ground connections
(AGND, DGND) should be kept separate as far back to the
source as possible (i.e., separate the ground planes on a local-
ized board, even if the grounds connect to a common point in
the system). Bypass capacitors should be placed as close to the
device pin as possible. Usually a multitiered bypassing scheme
consisting of a small high frequency capacitor (100 pF) placed
close to the supply pin and progressively larger capacitors
(0.1 µF, 10 µF) further back to the actual supply source works best.

Table 13. Power-Down Control Functions

Control Mode

Active

Description

PWRDWNCTL = 0 CFR1<3> Don't Care

Software Control

Digital Power-Down = CFR1<7>
Comparator Power-Down = CFR1<6>
DAC Power-Down = CFR1<5>
Input Clock Power-Down = CFR1<4>

PWRDWNCTL = 1 CFR1<3> = 0

External Control,
Fast Recovery Power-Down Mode

Digital Power-Down = 1'b1
Comparator Power-Down = 1'b0 Or CFR1<6>
DAC Power-Down = 1'b0
Input Clock Power-Down = 1'b0

PWRDWNCTL = 1 CFR1<3> = 1

External Control,
Full Power-Down Mode

Digital Power-Down = 1'b1
Comparator Power-Down = 1'b1
DAC Power-Down = 1'b1
Input Clock Power-Down = 1'b1

AD9954

Rev. 0 | Page 36 of 36

OUTLINE DIMENSIONS

BOTTOM VIEW

(PINS UP)

TOP VIEW

(PINS DOWN)

0.50

BSC

0.27
0.22
0.17

9.00

BSC SQ

7.00

BSC SQ

VIEW A

0.75
0.60
0.45

VIEW A

1.05
1.00
0.95

7°

3.5°

0°

SEATING

PLANE

0.15
0.05

EXPOSED

PAD

2.00

1.20

MAX

COMPLIANT TO JEDEC STANDARDS MS-026-ABC

Figure 33. 48-Lead Thin Plastic Quad Flat Package, Exposed Pad [TQFP/EP] (SV-48)--Dimensions shown in millimeters

ESD CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the
human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.

WARNING--Please note that this device in its current form does not meet Analog Devices' standard requirements for ESD as
measured against the charged device model (CDM). As such, special care should be used when handling this product, especially in
a manufacturing environment. Analog Devices will provide a more ESD hardy product in the near future at which time this warn-
ing will be removed from this data sheet.

ORDERING GUIDE

AD9954 Products

Temperature Range

Package Description

Package Outline

AD9954YSV

40°C to +105°C

48-Lead Thin Plastic Quad Flat Package, Exposed Pad (TQFP/EP)

SV-48

AD9954YSV-REEL7

40°C to +105°C

500 Device 7-Inch Reel of 48-Lead TQFP/EP

SV-48

AD9954/PCB

Evaluation

Board

C03374-0-10/03(0)

РР»РµРєС‚СЂРѕРЅРЅС‹Р№ РєРѕРјРїРѕРЅРµРЅС‚: AD9954

Document Outline

Р­Р»РµРєС‚СЂРѕРЅРЅС‹Р№ РєРѕРјРїРѕРЅРµРЅС‚: AD9954

Document Outline

РР»РµРєС‚СЂРѕРЅРЅС‹Р№ РєРѕРјРїРѕРЅРµРЅС‚: AD9954