Single Channel, High Speed
Optocouplers
Technical Data
Features
� 15 kV/
�
s Minimum Common
Mode Transient Immunity at
V
CM
= 1500 V (4503/0453)
� High Speed: 1 Mb/s
� TTL Compatible
� Available in 8-Pin DIP, SO-8,
Widebody Packages
� Open Collector Output
� Guaranteed Performance
from Temperature: 0
�
C
to 70
�
C
� Safety Approval
UL Recognized � 3750 V rms
for 1 minute (5000 V rms for
1 minute for HCNW and
Option 020 devices) per
UL1577
CSA Approved
IEC/EN/DIN EN 60747-5-2
Approved
�V
IORM
= 630 V
peak
for
HCPL-4503#060
�V
IORM
= 1414 V
peak
for
HCNW devices
� Dual Channel Version
Available (253X/4534/053X/
0534)
� MIL-PRF-38534 Hermetic
Version Available (55XX/
65XX/4N55)
Applications
� High Voltage Insulation
� Video Signal Isolation
� Power Transistor Isolation
in Motor Drives
� Line Receivers
� Feedback Element in
Switched Mode Power
Supplies
� High Speed Logic Ground
Isolation � TTL/TTL, TTL/
CMOS, TTL/LSTTL
� Replaces Pulse Transformers
� Replaces Slow
Phototransistor Isolators
� Analog Signal Ground
Isolation
Description
These diode-transistor optocoup-
lers use an insulating layer
between a LED and an integrated
photodetector to provide elec-
trical insulation between input
and output. Separate connections
for the photodiode bias and
output-transistor collector
increase the speed up to a
hundred times that of a conven-
tional phototransistor coupler by
reducing the base-collector
capacitance.
Functional Diagram
6N135/6
HCNW135/6
HCNW4502/3
HCPL-2502
HCPL-0452/3
HCPL-0500/1
HCPL-4502/3
CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to
prevent damage and/or degradation which may be induced by ESD.
A 0.1
�
F bypass capacitor must be connected between pins 5 and 8.
7
1
2
3
4
5
6
8
NC
ANODE
CATHODE
NC
VCC
VB
VO
GND
*
* NOTE: FOR 4502/3, 0452/3,
PIN 7 IS NOT CONNECTED.
TRUTH TABLE
(POSITIVE LOGIC)
LED
ON
OFF
VO
LOW
HIGH
2
IF
SHIELD
HCPL-4503/0453
HCNW4503
8
6
5
GND
VCC
2
3
VO
ICC
VF
IO
ANODE
CATHODE
+
�
7
VB
IB
*
* NOTE: FOR HCPL-4502/-3, HCPL-0452/3,
HCNW4502/3, PIN 7 IS NOT CONNECTED.
Ordering Information
Specify Part Number followed by Option Number (if desired).
Example:
HCPL-4503#XXXX
020 = UL 5000 V rms/1 Minute Option*
060 = IEC/EN/DIN EN 60747-5-2 V
IORM
= 630 V
peak
Option**
300 = Gull Wing Surface Mount Option
500 = Tape and Reel Packaging Option
XXXE = Lead Free Option
Option data sheets available. Contact your Agilent sales representative or authorized distributor for information.
*For 6N135/6 and HCPL-4502/3 only.
**For HCPL-4503 only. Combination of Option 020 and Option 060 is not available.
Gull wing surface mount option applies to through hole parts only.
Schematic
Selection Guide
Widebody
Minimum CMR
8-Pin DIP (300 Mil)
Small-Outline SO-8
(400 Mil)
Hermetic
Current
Single
Dual
Single
Dual
Single
Single and
dV/dt
V
CM
Transfer
Channel
Channel
Channel
Channel
Channel
Dual Channel
(V/
�
s)
(V)
Ratio (%)
Package
Package*
Package
Package*
Package
Packages*
1,000
10
7
6N135
HCPL-2530
HCPL-0500
HCPL-0530
HCNW135
19
6N136
HCPL-2531
HCPL-0501
HCPL-0531
HCNW136
HCPL-4502
HCPL-0452
HCNW4502
15
HCPL-2502
15,000
1500
19
HCPL-4503
HCPL-4534
HCPL-0453
HCPL-0534
HCNW4503
1,000
10
9
HCPL-55XX
HCPL-65XX
4N55
*Technical data for these products are on separate Agilent publications.
Pin 7, transistor base, is not connected.
output current for 1 TTL load and
a 5.6 k
pull-up resistor. CTR for
these devices is 19% minimum at
I
F
= 16 mA.
The HCPL-4502, HCPL-0452,
and HCNW4502 provide the
electrical and switching
performance of the 6N136,
HCPL-0501, and HCNW136 with
increased ESD protection.
The HCPL-4503, HCPL-0453,
and HCNW4503 are similar to the
HCPL-4502, HCPL-0452, and
HCNW4502 optocouplers but
have increased common mode
transient immunity of 15 kV/
�
s
minimum at V
CM
= 1500 V
guaranteed.
These single channel optocoup-
lers are available in 8-Pin DIP,
SO-8 and Widebody package
configurations.
The 6N135, HCPL-0500, and
HCNW135 are for use in TTL/
CMOS, TTL/LSTTL or wide
bandwidth analog applications.
Current transfer ratio (CTR) for
these devices is 7% minimum at
I
F
= 16 mA.
The 6N136, HCPL-2502,
HCPL-0501, and HCNW136 are
designed for high speed TTL/TTL
applications. A standard 16 mA
TTL sink current through the
input LED will provide enough
Remarks: The notation "#" is used for existing products, while (new) products launched since 15th July
2001 and lead free option will use "-"
3
Package Outline Drawings
8-Pin DIP Package (6N135/6, HCPL-4502/3, HCPL-2502)
8-Pin DIP Package with Gull Wing Surface Mount Option 300 (6N135/6, HCPL-4502/3)
1.080 � 0.320
(0.043 � 0.013)
2.54 � 0.25
(0.100 � 0.010)
0.51 (0.020) MIN.
0.65 (0.025) MAX.
4.70 (0.185) MAX.
2.92 (0.115) MIN.
5� TYP.
0.254
+ 0.076
- 0.051
(0.010
+ 0.003)
- 0.002)
7.62 � 0.25
(0.300 � 0.010)
6.35 � 0.25
(0.250 � 0.010)
9.65 � 0.25
(0.380 � 0.010)
1.78 (0.070) MAX.
1.19 (0.047) MAX.
A XXXXZ
YYWW
DATE CODE
DIMENSIONS IN MILLIMETERS AND (INCHES).
5
6
7
8
4
3
2
1
OPTION CODE*
UL
RECOGNITION
UR
TYPE NUMBER
*MARKING CODE LETTER FOR OPTION NUMBERS
"L" = OPTION 020
"V" = OPTION 060
OPTION NUMBERS 300 AND 500 NOT MARKED.
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
3.56 � 0.13
(0.140 � 0.005)
0.635 � 0.25
(0.025 � 0.010)
12� NOM.
9.65 � 0.25
(0.380 � 0.010)
0.635 � 0.130
(0.025 � 0.005)
7.62 � 0.25
(0.300 � 0.010)
5
6
7
8
4
3
2
1
9.65 � 0.25
(0.380 � 0.010)
6.350 � 0.25
(0.250 � 0.010)
1.016 (0.040)
1.27 (0.050)
10.9 (0.430)
2.0 (0.080)
LAND PATTERN RECOMMENDATION
1.080 � 0.320
(0.043 � 0.013)
3.56 � 0.13
(0.140 � 0.005)
1.780
(0.070)
MAX.
1.19
(0.047)
MAX.
2.54
(0.100)
BSC
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
0.254
+ 0.076
- 0.051
(0.010
+ 0.003)
- 0.002)
4
Small Outline SO-8 Package (HCPL-0500/1, HCPL-0452/3)
8-Pin Widebody DIP Package (HCNW135/6, HCNW4502/3)
XXX
YWW
8
7
6
5
4
3
2
1
5.994 � 0.203
(0.236 � 0.008)
3.937 � 0.127
(0.155 � 0.005)
0.406 � 0.076
(0.016 � 0.003)
1.270
(0.050)
BSC
5.080 � 0.127
(0.200 � 0.005)
3.175 � 0.127
(0.125 � 0.005)
1.524
(0.060)
45� X
0.432
(0.017)
0.228 � 0.025
(0.009 � 0.001)
TYPE NUMBER
(LAST 3 DIGITS)
DATE CODE
0.305
(0.012)
MIN.
TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH)
5.207 � 0.254 (0.205 � 0.010)
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX.
0.203 � 0.102
(0.008 � 0.004)
7�
PIN ONE
0 ~ 7�
*
*
7.49 (0.295)
1.9 (0.075)
0.64 (0.025)
LAND PATTERN RECOMMENDATION
5
6
7
8
4
3
2
1
11.15 � 0.15
(0.442 � 0.006)
1.78 � 0.15
(0.070 � 0.006)
5.10
(0.201)
MAX.
1.55
(0.061)
MAX.
2.54 (0.100)
TYP.
DIMENSIONS IN MILLIMETERS (INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
7� TYP.
0.254
+ 0.076
- 0.0051
(0.010
+ 0.003)
- 0.002)
11.00
(0.433)
9.00 � 0.15
(0.354 � 0.006)
MAX.
10.16 (0.400)
TYP.
A
HCNWXXXX
YYWW
DATE CODE
TYPE NUMBER
0.51 (0.021) MIN.
0.40 (0.016)
0.56 (0.022)
3.10 (0.122)
3.90 (0.154)
5
8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW135/6,
HCNW4502/3)
Solder Reflow Temperature Profile
0
TIME (SECONDS)
TEMPERATURE (
�
C)
200
100
50
150
100
200
250
300
0
30
SEC.
50 SEC.
30
SEC.
160�C
140�C
150�C
PEAK
TEMP.
245�C
PEAK
TEMP.
240�C
PEAK
TEMP.
230�C
SOLDERING
TIME
200�C
PREHEATING TIME
150�C, 90 + 30 SEC.
2.5�C � 0.5�C/SEC.
3�C + 1�C/�0.5�C
TIGHT
TYPICAL
LOOSE
ROOM
TEMPERATURE
PREHEATING RATE 3�C + 1�C/�0.5�C/SEC.
REFLOW HEATING RATE 2.5�C � 0.5�C/SEC.
1.00 � 0.15
(0.039 � 0.006)
7� NOM.
12.30 � 0.30
(0.484 � 0.012)
0.75 � 0.25
(0.030 � 0.010)
11.00
(0.433)
5
6
7
8
4
3
2
1
11.15 � 0.15
(0.442 � 0.006)
9.00 � 0.15
(0.354 � 0.006)
1.3
(0.051)
13.56
(0.534)
2.29
(0.09)
LAND PATTERN RECOMMENDATION
1.78 � 0.15
(0.070 � 0.006)
4.00
(0.158)
MAX.
1.55
(0.061)
MAX.
2.54
(0.100)
BSC
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
0.254
+ 0.076
- 0.0051
(0.010
+ 0.003)
- 0.002)
MAX.
PDF 
ZIP