1-49
H
T-1
3
/
4
(5 mm), T-1 (3 mm), High
Performance, Tinted, Diffused,
AlInGaP, and TS AlGaAs Red
LED Lamps
Technical Data
HLMA-DX05 Series
HLMA-KX05 Series
HLMP-D1XX Series
HLMP-J100/J150 Series
Features
High Light Output Over a
Wide Range of Currents
Popular T-1 and T-1
3
/
4
Packages
Choice of Three Colors
Amber
Reddish-Orange
Deep Red
Wide Viewing Angles
Long Life: Solid State
Technology
Available on Tape and Reel
Applications
Outdoor Message Boards
Automotive Lighting
Portable Equipment
Medical Equipment
Changeable Message Signs
Description
The HLMA-D/KXXX series tinted,
diffused, solid state lamps utilize
the newly developed aluminum
indium gallium phosphide
(AlInGaP) LED technology. This
technology has a very high
luminous efficiency, capable of
producing high light output over a
wide range of drive currents.
These LED lamps are available
with a choice of two colors, 592
nm amber and 615 nm reddish-
orange, and with two viewing
angles, 65
and 60
.
The HLMP-D/JXXX series tinted,
diffused solid state lamps utilize
the highly optimized transparent
substrate aluminum gallium
arsenide (TS AlGaAs) LED
technology. This technology has a
very high luminous efficiency,
Device Selection Guide
Viewing
Reddish-
Deep
Angle
Amber
Orange
Red
Package
Package Description
2
1
/
2
d
= 592 nm
d
= 615 nm
d
= 644 nm
Outline
T-1
3
/
4
(5 mm), Tinted, Diffused,
65
HLMA-
HLMA-
A
Standard Current
DL05
DH05
T-1 (3 mm), Tinted, Diffused,
60
HLMA-
HLMA-
B
Standard Current
KL05
KH05
T-1
3
/
4
(5 mm), Tinted, Diffused,
40
HLMP-
A
Standard Current
D115
T-1
3
/
4
(5 mm), Tinted, Diffused,
25
HLMP-
A
Standard Current
D120
T-1 (3 mm), Tinted, Diffused,
55
HLMP-
C
Standard Current
J100
T-1 (3 mm), Tinted, Diffused,
55
HLMP-
C
Diffused, Low Current
J150
5964-9287E
1-50
0.89 (0.035)
0.64 (0.025)
0.45 (0.018)
SQUARE
NOMIMAL
5.08 (0.200)
4.57 (0.180)
9.19 (0.362)
8.43 (0.332)
25.40
(1.00)
MIN.
1.27( 0.050) NOM.
CATHODE
6.10 (0.240)
5.59 (0.220)
2.54 (0.100) NOM.
CATHODE
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES).
2. AN EPOXY MENISCUS MAY EXTEND ABOUT
1 mm (0.040") DOWN THE LEADS.
Package Dimensions
3.18 (0.125)
2.67 (0.105)
24.13
(0.95)
MIN.
1.27
(0.050)
NOM.
1.02
(0.040)
6.35 (0.250)
5.58 (0.220)
0.45
(0.018)
SQUARE NOMINAL
CATHODE
2.54
(0.100)
NOM.
NOM.
4.70 (0.185)
4.19 (0.165)
3.43 (0.135)
2.92 (0.115)
ANODE
3.18 (0.125)
2.67 (0.105)
24.13
(0.95)
MIN.
1.27
(0.050)
NOM.
1.02
(0.040)
6.35 (0.250)
5.58 (0.220)
0.45
(0.018)
SQUARE
NOMINAL
ANODE
2.54
(0.100)
NOM.
NOM.
4.70 (0.185)
4.19 (0.165)
3.43 (0.135)
2.92 (0.115)
CATHODE
A
B
C
HLMA-DL05/DH05/Kl05/KH05 AlInGaP Lamps
Absolute Maximum Ratings at T
A
= 25
C
HLMA-
HLMA-
HLMA-
HLMA-
Parameter
DL05
DH05
KL05
KH05
Units
DC Forward Current
[1,3,4]
50
50
50
50
mA
Peak Forward Current
[2]
200
200
200
200
mA
Average Input Power
[2]
103
103
103
103
mW
Reverse Voltage (I
R
= 100
A)
5
5
5
5
V
Operating Temperature Range
-40 to
-40 to
-40 to
-40 to
C
+100
+100
+100
+100
Storage Temperature Range
-55 to
-55 to
-55 to
-55 to
C
+100
+100
+100
+100
Junction Temperature
110
C
Soldering Temperature
260
C for 5 second
[1.59 mm (0.06 in.) below seating plane]
Notes:
1. Derate linearly as shown in Figure 4.
2. Any pulsed operation cannot exceed the Absolute Max Peak Forward current as specified in Figure 5.
3. Drive currents between 10 mA and 30 mA are recommended for best long term performance.
4. Operation at currents below 10 mA is not recommended, please contact your Hewlett-Packard sales representative.
capable of producing high light
output over the wide range of
drive currents from 500
A to
50 mA. The color is deep red at a
dominant wavelength of 644 nm.
TS AlGaAs is a flip-chip LED
technology, die attached to the
anode lead and wire bonded to
the cathode lead. Available view-
ing angles are 25
, 40
, and 55
.
1-51
Optical Characteristics at T
A
= 25
C
Luminous
Color,
Viewing
Intensity
Peak
Dominant
Angle
Luminous
I
V
(mcd)
Wavelength
Wavelength
2
1
/
2
Efficacy
Part Number
@ 20 mA
[1]
peak
(nm)
d
[2]
(nm)
Degrees
[3]
v
HLMA-
Min.
Typ.
Typ.
Typ.
Typ.
(lm/w)
DL05
35
100
594
592
65
480
DH05
35
100
621
615
65
263
KL05
35
100
594
592
60
480
KH05
35
100
621
615
60
263
Notes:
1.
v
is the total luminous flux output as measured with an integrating sphere.
2. The dominant wavelength,
d
, is derived from the CIE Chromaticity Diagram and represents the color of the device.
3.
1
/
2
is the off-axis angle where the luminous intensity is 1/2 the peak intensity.
Electrical Characteristics at T
A
= 25
C
Forward
Reverse
Capacitance
Speed of Response
Voltage
Breakdown
C (pF)
s (ns)
Part
V
F
(Volts)
V
R
(Volts)
V
F
= 0,
Thermal
Time Constant
Number
@ I
F
= 20 mA
@ I
R
= 100
A
f = 1 mHz
Resistance
e
-t/
s
HLMA-
Typ.
Max.
Min.
Typ.
Typ.
R
J-PIN
(
C/W)
Typ.
DL05
1.9
2.4
5
25
60
260
13
DH05
1.9
2.4
5
25
60
260
13
KL05
1.9
2.4
5
25
60
290
13
KH05
1.9
2.4
5
25
60
290
13
WAVELENGTH nm
550
RELATIVE INTENSITY
600
700
650
AMBER
1.0
0.5
0
REDDISH-ORANGE
594
621
630
Figure 1. Relative Intensity vs.
Wavelength.
Figure 2. Forward Current vs.
Forward Voltage.
I F
FORWARD CURRENT mA
1.0
0
VF FORWARD VOLTAGE V
2.5
200
120
80
1.5
2.0
160
3.0
40
20
60
100
140
180
1-52
Figure 3. Relative Luminous Intensity
vs. Forward Current.
Figure 4. Maximum Forward Current
vs. Ambient Temperature. Derating
Based on T
J
Max = 110
C.
NORMALIZED INTENSITY
1.0
0
ANGULAR DISPLACEMENT DEGREES
0.8
0.6
0.5
0.7
0.2
100 90
0.1
0.3
0.4
80 70 60 50 40
20 10
0
30
10 20 30 40 50 60 70 80 90 100
0.9
Figure 6. Spatial Radiation Pattern for HLMA-DL05/DH05 65
Lamps.
NORMALIZED INTENSITY
1.0
0
ANGULAR DISPLACEMENT DEGREES
0.8
0.6
0.5
0.7
0.2
100 90
0.1
0.3
0.4
80 70 60 50 40
20 10
0
30
10 20 30 40 50 60 70 80 90 100
0.9
20
T AMBIENT TEMPERATURE
C
A
5
15
35
0
50
30
45
10
0
50
I FORWARD CURRENT mA
F
10
20
40
90
60
25
30
40
70 80
100
R
= 618
C/W
J-A
R
= 412
C/W
J-A
50
40
20
10
0
50
100
I AVERAGE CURRENT mA
AVG
I PEAK FORWARD CURRENT mA
PEAK
150
30
200
f
100 Hz
f
300 Hz
f
1 KHz
Figure 5. Maximum Average Current
vs. Peak Forward Current.
Figure 7. Spatial Radiation Pattern for HLMA-KL05/KH05 60
Lamps.
2.5
2.0
1.5
1.0
0.0
0
10
50
20
40
30
I
F
DC FORWARD CURRENT mA
RELATIVE LUMINOUS INTENSITY
(NORMALIZED AT 20 mA)
0.5
1-53
HLMP-D115/D120/J100/J150 TS AlGaAs Red Lamps
Absolute Maximum Ratings at T
A
= 25
C
HLMP-
HLMP-
HLMP-
HLMP-
Parameter
D115
D120
J100
J150
Units
DC Forward Current
[1]
50
50
50
50
mA
Peak Forward Current
[2]
300
300
300
300
mA
Average Input Power
[2]
100
100
100
100
mW
Reverse Voltage (I
R
= 100
A)
5
5
5
5
V
Operating Temperature Range
-55 to
-55 to
-55 to
-55 to
C
+100
+100
+100
+100
Storage Temperature Range
-55 to
-55 to
-55 to
-55 to
C
+100
+100
+100
+100
Junction Temperature
110
C
Soldering Temperature
260
C for 5 second
[1.59 mm (0.06 in.) below seating plane]
Notes:
1. Derate linearly as shown in Figure 12.
2. Any pulsed operation cannot exceed the Absolute Max Peak Forward current as specified in Figure 13.
Optical Characteristics at T
A
= 25
C
Luminous
Color,
Viewing
Intensity
Peak
Dominant
Angle
Luminous
I
V
(mcd)
Wavelength
Wavelength
2
1/2
Efficacy
Part Number
@ 20 mA
[1]
peak
(nm)
d
[2]
(nm)
Degrees
[3]
v
HLMP-
Min.
Typ.
Typ.
Typ.
Typ.
(lm/w)
D115
138
250
654
644
40
85
D120
138
350
654
644
25
85
J100
39
175
654
644
55
85
J150
1.3
3.0
654
644
55
85
Notes:
1.
v
is the total luminous flux output as measured with an integrating sphere.
2. The dominant wavelength,
d
, is derived from the CIE Chromaticity Diagram and represents the color of the device.
3.
1/2
is the off-axis angle where the luminous intensity is 1/2 the peak intensity.
Electrical Characteristics at T
A
= 25
C
Forward
Reverse
Capacitance
Speed of Response
Voltage
Breakdown
C (pF)
s (ns)
Part
V
F
(Volts)
V
R
(Volts)
V
F
= 0
Thermal
Time Constant
Number
@ I
F
= 20 mA
@ I
R
= 100
A
f = 1 mHz
Resistance
e
-t/
s
HLMP-
Min.
Typ.
Min.
Typ.
Typ.
R
J-PIN
(
C/W)
Typ.
D115
1.85
2.4
5
20
20
260
45
D120
1.85
2.4
5
20
20
260
45
J100
1.85
2.4
5
20
20
290
45
J150
1.6
1.9
5
20
20
290
45
PDF 
ZIP