Agilent HLMP-Cxxx
T-1
3
/
4
(5 mm) Extra Bright Precision
Optical Performance InGaN LED Lamps
Data Sheet
Description
These high intensity blue and
green LEDs are based on the
most efficient and cost effective
InGaN material technology. The
470 nm typical dominant wave
length for blue and 525 nm
typical wavelength for green is
well suited to color mixing in
full color signs. The 505 nm
typical dominant wavelength for
cyan is suitable for traffic signal
application.
These LED lamps are untinted,
non-diffused, T-1
3
/
4
packages
Features
Well defined spatial radiation
pattern
High luminous output
Available in blue, green, and cyan
color
Viewing angle: 15
, 23
and 30
Standoff or non-standoff leads
Superior resistance to moisture
Applications
Traffic signals
Commercial outdoor advertising
Front panel backlighting
Front panel indicator
incorporating second generation
optics which produce well-defined
spatial radiation patterns at
specific viewing cone angles.
These lamps are made with an
advanced optical grade epoxy,
offering superior temperature
and moisture resistance in
outdoor signal and sign
applications. The high maximum
LED junction temperature limit
of +110
C enables high
temperature operation in bright
sunlight conditions.
HLMP-CB11, HLMP-CB12, HLMP-CM11, HLMP-CM12, HLMP-CE11,
HLMP-CE12, HLMP-CB26, HLMP-CB27, HLMP-CM26, HLMP-CM27,
HLMP-CE26, HLMP-CE27, HLMP-CB36, HLMP-CB37, HLMP-CM36,
HLMP-CM37, HLMP-CE36, HLMP-CE37
CAUTION: Devices are Class I ESD sensitive. Please observe appropriate precautions during
handling and processing. Refer to Application Note AN-1142 for additional details.
2
Package Dimensions
1.14
0.20
(0.045
0.008)
NOTE 1
5.80
0.20
(0.228
0.008)
5.00
0.20
(0.197
0.008)
31.60
(1.244)
MIN.
0.70 (0.028)
MAX.
1.00
(0.039)
MIN.
8.71
0.20
(0.343
0.008)
2.54
0.38
(0.100
0.015)
0.50
0.10
(0.020
0.004)
SQ. TYP.
CATHODE
LEAD
2.35 (0.093)
MAX.
CATHODE
FLAT
Package A
Package B
5.80
0.20
(0.228
0.008)
2.54
0.38
(0.100
0.015)
CATHODE
FLAT
1.14
0.20
(0.045
0.008)
NOTE 1
5.00
0.20
(0.197
0.008)
31.60
(1.244)
MIN.
0.70 (0.028)
MAX.
1.50
0.15
(0.059
0.006)
1.00
(0.039)
MIN.
8.71
0.20
(0.343
0.008)
DIMENSION H
(REFER TO TABLE BELOW)
0.50
0.10
(0.020
0.004)
SQ. TYP.
NOTES:
1. MEASURED JUST ABOVE FLANGE.
2. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES).
3. EPOXY MENISCUS MAY EXTEND ABOUT 1 mm (0.040") DOWN THE LEADS.
4. IF HEAT SINKING APPLICATION IS REQUIRED, THE TERMINAL FOR HEAT SINK IS ANODE.
DIMENSION H:
15
= 11.40
0.25 mm (0.449
0.01 INCH)
23
= 11.85
0.25 mm (0.467
0.01 INCH)
30
= 11.50
0.25 mm (0.453
0.01 INCH)
CATHODE
LEAD
3
Device Selection Guide
Typical
Viewing Angle,
Intensity (cd) at 20 mA
Package
Part Number
Color
2q
1
/
2
(Degree)
Min.
Max.
Standoff
Dimension
Lens
HLMP-CB11-TW0xx
Blue
15
2.5
7.2
No
A
Clear
HLMP-CB11-UVAxx
Blue
15
3.2
5.5
No
A
Clear
HLMP-CB12-TW0xx
Blue
15
2.5
7.2
Yes
B
Clear
HLMP-CM11-Y20xx
Green
15
9.3
27.0
No
A
Clear
HLMP-CM11-Z1Cxx
Green
15
12.0
21.0
No
A
Clear
HLMP-CM12-Y20xx
Green
15
9.3
27.0
Yes
B
Clear
HLMP-CE11-X10xx
Cyan
15
7.2
21.0
No
A
Clear
HLMP-CE12-X10xx
Cyan
15
7.2
21.0
Yes
B
Clear
HLMP-CB26-SV0xx
Blue
23
1.9
5.5
No
A
Clear
HLMP-CB26-TUDxx
Blue
23
2.5
4.2
No
A
Clear
HLMP-CB27-SV0xx
Blue
23
1.9
5.5
Yes
B
Clear
HLMP-CM26-X10xx
Green
23
7.2
21.0
No
A
Clear
HLMP-CM26-YZCxx
Green
23
9.3
16.0
No
A
Clear
HLMP-CM27-X10xx
Green
23
7.2
21.0
Yes
B
Clear
HLMP-CE26-WZ0xx
Cyan
23
5.5
16.0
No
A
Clear
HLMP-CE27-WZ0xx
Cyan
23
5.5
16.0
Yes
B
Clear
HLMP-CB36-QT0xx
Blue
30
1.15
3.2
No
A
Clear
HLMP-CB36-RSAxx
Blue
30
1.5
2.5
No
A
Clear
HLMP-CB37-RU0xx
Blue
30
1.5
4.2
Yes
B
Clear
HLMP-CB37-RSDxx
Blue
30
1.5
2.5
Yes
B
Clear
HLMP-CM36-X10xx
Green
30
7.2
21.0
No
A
Clear
HLMP-CM36-XYCxx
Green
30
7.2
12.0
No
A
Clear
HLMP-CM37-X10xx
Green
30
7.2
21.0
Yes
B
Clear
HLMP-CM37-XYCxx
Green
30
7.2
12.0
Yes
B
Clear
HLMP-CM37-XYDxx
Green
30
7.2
12.0
Yes
B
Clear
HLMP-CE36-WZ0xx
Cyan
30
5.5
16.0
No
A
Clear
HLMP-CE37-WZ0xx
Cyan
30
5.5
16.0
Yes
B
Clear
Notes:
1. Tolerance for luminous intensity measurement is
15%.
2. The luminous intensity is measured on the mechanical axis of the lamp package.
3. The optical axis is closely aligned with the package mechanical axis.
4. LED light output is bright enough to cause injuries to the eyes. Precautions must be taken to prevent looking directly at the LED without proper
safety equipment.
5. 2q
1/2
is the off-axis angle where the luminous intensity is 1/2 the
on-axis intensity.
4
Part Numbering System
HLMP - x x xx - x x x xx
Mechanical Options
00: Bulk
DD: Ammo Pack
Color Bin Options
0: Full Color Bin Distribution
A: Color Bin 1 and 2
C: Color Bin 3 and 4
D: Color Bin 4 and 5
Maximum Intensity Bin
0: No Maximum Intensity Bin Limitation
Others: Refer to Device Selection Guide
Minimum Intensity Bin
Refer to Device Selection Guide
Viewing Intensity Bin
11: 15
Without Standoff
12: 15
With Standoff
26: 23
Without Standoff
27: 23
With Standoff
36: 30
Without standoff
37: 30
With Standoff
Color
B: Blue 470 nm
M: Green 525 nm
E: Cyan 505 nm
Package
C: T-1
3
/
4
(5 mm) Round Lamp
5
Absolute Maximum Rating at T
A
= 25
C
Parameters
Value
Unit
DC Forward Current
[1]
30
mA
Peak Pulsed Forward Current
[3]
100
mA
Average Forward Current
30
mA
Power Dissipation
120
mW
LED Junction Temperature
110
C
Operating Temperature Range
40 to +85
C
Storage Temperature Range
40 to +100
C
Wave Soldering Temperature
[2]
250 for 3 secs
C
Notes:
1. Derate linearly as shown in Figure 2.
2. 1.59 mm (0.060 inch) below body.
3. Duty factor 10%, frequency 1 KHz.
Electrical/Optical Characteristics
T
A
= 25
o
C
Blue
Green
Cyan
Parameters
Symbol
Min. Typ. Max.
Min. Typ. Max.
Min. Typ. Max.
Units
Test Condition
Forward Voltage
V
F
3.5
4.0
3.6
4.0
3.5
4.0
V
I
F
= 20 mA
Reverse Voltage
[1]
V
R
5.0
5.0
5.0
V
I
R
= 10
A
Thermal Resistance
Rq
J-PIN
240
240
240
o
C/W
LED Junction to
Anode Lead
Dominant
l
d
460
470 480
520
525 540
490 505 510
nm
I
F
= 20 mA
Wavelength
[2]
Peak Wavelength
l
PEAK
464
516
501
nm
Peak of Wavelength
of Spectral Distribu-
tion at I
F
= 20 mA
Spectral Half Width
Dl
1/2
23
32
30
nm
Wavelength Width
at Spectral Distribu-
tion Power Point
at I
F
= 20 mA
Luminous Efficacy
[3]
h
v
74
484
319
lm/W Emitted Luminous
Power/Emitted
Radiant Power
Notes:
1. The reverse voltage of the product is equivalent to the forward voltage of the protective chip at I
R
= 10
A.
2. The dominant wavelength, l
d
, is derived from the Chromaticity Diagram and represents the color of the lamp.
3. The radiant intensity, Ie in watts/steradian, may be found from the equation Ie = Iv/h
v
, where Iv is the luminous intensity in candelas and h
v
is the
luminous efficacy in lumens/watt.
PDF 
ZIP