LOW TO MEDIUM POWER AC/DC POWER SUPPLIES 80-110W AC/DC Universal Input Switch Mode Power Supplies

2 YEAR WARRANTY

NLP110 Medical Series

S i n g l e a n d t r i p l e o u t p u t

Provides low voltage outputs

Compliance to EN61000-3-2 (Power Factor = 0.98)

Smallest industry standard package 6.5 x 3.0 x 1.26 inches

90VAC to 264VAC universal input range

UL, cUL, and VDE safety approvals and CE-Marked to MDD

Overvoltage and short circuit protection

VDE0871-A, EN55022-A, EN55011-A conducted noise

VDE0871-A, EN55022-A, EN55011-A radiated noise

Meets all applicable and relevant immunity standards
EN61000-4-2,4,5 and 6

The NLP110 Medical is a series of 110W AC/DC open-frame power supplies in a
3" x 6.5" x 1.26" package. The NLP110 Medical is power factor corrected to meet EN61000-3-2
and is available in single and multiple output models. The multiple output models have a capability
that is unique to the power supply market - they can deliver equal amounts of current on multiple
low voltage outputs to support designs that will span the industry transition from 5V logic to 3.3V
logic. The NLP110 Medical is practically the same size as a 65 Watt 3" x 5" product, e.g. NLP65
Medical - the one difference is that the footprint is a mere 1.5 inches longer. The NLP110 Medical
series, with full medical safety approval per UL2601-1, C22.2 No. 601.1-M90, VDE0750,
IEC60601-1 and EN60601-1 and CE marked, greatly accelerating design-in time and reducing
system compliance costs.

All specifications are typical at nominal input, full load at 25°C unless otherwise stated

EMC CHARACTERISTICS (continued)

Surge

EN61000-4-5

Level 3

Fast transients

EN61000-4-4

Level 3

Radiated immunity

EN61000-4-3

Level 3

Conducted immunity

EN61000-4-6

Level 3

GENERAL SPECIFICATIONS

Hold-up time

120VAC, 60Hz

16.7ms @ 110W

Efficiency

120VAC, 80W (-9605)

75% min.

Isolation voltage

Input/output

4000VAC

Input/chassis

1500VAC

Approvals and

EN60601-1, IEC60601-1,VDE0750,

standards

UL2601-1, C22.2 No. 601.1-M90

Weight

283g (10oz)

MTBF (@ 25°C)

MIL-HDBK-217F

220,000 hours min.

ENVIRONMENTAL SPECIFICATIONS

(9)

Thermal performance

Operating ambient,

0°C to +50°C

(See derating curve)
Non-operating

-40°C to +85°C

50°C to 70°C, ambient,

Derate to

convection cooled

50% load

0°C to 50°C, ambient,

80W

convection cooled
0°C to 50°C ambient,

110W

150LFM forced air
Peak (0°C to +50°C, 60s)

(See Note 3)

Relative humidity

Non-condensing

5% to 95% RH

Altitude

Operating

10,000 feet max.

Non-operating

30,000 feet max.

Vibration (See Note 8)

5Hz to 500Hz

2.4G rms peak

Shock

per MIL-STD-810E

516.4 Part IV

OUTPUT SPECIFICATIONS

Total regulation

Main output

±2.0%

(Line and load)

Auxiliary outputs

±5.0%

Rise time

At turn-on

1.0s, max.

Transient response

Main output

5.0% or 250mV

75% to 100%

max. dev., 1ms max.

step at 0.1A/µs

recovery to 1%

Temperature coefficient

±0.02%/°C

Overvoltage protection

Main outputs

125%, ±10%

Short circuit protection

Cyclic operation

Continuous

Minimum output current

Single and multiple

See table

INPUT SPECIFICATIONS

Input voltage range

Universal input

90 to 264VAC

(See Note 6)

Input frequency range

47Hz to 63Hz

Input surge current

120VAC

18A max.

(cold start)

230VAC

35A max.

Safety ground

230VAC, 50Hz

<100µA

leakage current

Input current

120VAC @ 80W

0.9A rms

120VAC @ 110W

1.3A rms

230VAC @ 80W

0.48A rms

230VAC @ 110W

0.7A rms

Input fuse

UL/IEC127

F3.15A H, 250VAC

EMC CHARACTERISTICS

(12)

Conducted emissions

EN55022, FCC part 15

Level A

Radiated emissions

EN55022, FCC part 15

Level A

Harmonic current

EN61000-3-2

Compliant

emission correction
ESD air

EN61000-4-2

Level 3

ESD contact

EN61000-4-2

Level 3

SPECIFICATIONS

File Name: NLP110M.PDF Rev: 13 Dec 2002

For the most current data and application support visit www.artesyn.com/powergroup/products.htm

Notes

Free air convection.
Multiple output units: maximum continuous output power not to exceed
80W.
For -9993; I

3.3V

= 13A max.; I

5.0V

= 13A max.; I

3.3V

+ I

5.0V

16A.

For -9994; I

3.3V

= 13A max.; I

2.5V

= 13A max.; I

3.3V

+ I

2.5V

16A

For -9995; I

3.3V

= 13A max.; I

12V

= 6.5A max.; I

3.3V

+ I

12V

16A.

For -9908; I

5.0V

= 13A max.; I

12V

= 6.5A max.; I

5.0V

+ I

12V

16A.

Single output units: maximum continuous output power not to exceed;
75W on 9905; 76.8W on 9912,-9924, and 9917.

150LFM forced air cooling from L4 side.
Multiple output units: maximum continuous output power not to exceed
105W.
For -9993; I

3.3V

= 16A max.; I

5.0V

= 16A max.; I

3.3V

+ I

5.0V

20A.

For -9994; I

3.3V

= 16A max.; I

2.5V

= 16A max.; I

3.3V

+ I

2.5V

20A

For -9995; I

3.3V

= 16A max.; I

12V

= 8.5A max.; I

3.3V

+ I

12V

20A.

For -9908; I

5.0V

= 16A max.; I

12V

= 8.5A max.; I

5.0V

+ I

12V

20A.

Single output units: maximum continuous output power not to exceed
110W for all models.

300LFM forced air cooling from L4 side.
Multiple output units: maximum continuous output power not to exceed
110W.
For -9993; I

3.3V

= 20A max.; I

5.0V

= 18A max.; I

3.3V

+ I

5.0V

22A.

For -9994; I

3.3V

= 20A max.; I

2.5V

= 20A max.; I

3.3V

+ I

2.5V

22A

For -9995; I

3.3V

= 20A max.; I

12V

= 8.5A max.; I

3.3V

+ I

12V

22A.

For -9908; I

5.0V

= 20A max.; I

12V

= 8.5A max.; I

5.0V

+ I

12V

22A.

Single output units: maximum continuous output power not to exceed
110W for all models.

Peak output current lasting less than 30 seconds with duty cycle less
than 5%. During peak loading, output voltage may exceed total
regulation limits.

Figure is peak-to-peak for convection power rating. Output noise
measurements are made across a 20MHz bandwidth using a 6" twisted
pair, terminated with a 10µF electrolytic capacitor and a 0.1µF ceramic
capacitor.

Minimum load required for correct start-up and operation on single
outputs and on main output of multiple versions. Failure to observe
minimum load on main output will not allow the supply to start-up
correctly. Some electronic test loads have a large delay time before they
start drawing current even though the voltage from the supply is present.
During this time delay, there is no load on the output and as a result, the
supply cannot start-up properly and maintain its correct output voltage.
In these instances, a dummy resistive load across the output may be
necessary to load the output of the supply until the test load can function
correctly and draw the intended minimum load. Minimum load required
on auxiliary outputs to maintain regulation.

For models NLP110-9908 and NLP110-9995, the 12V output is floating.
For -12V output, pin 11 on J2 has to be connected to Return making pin
12 the -12V output

Three orthogonal axes, random vibration 10 minutes for each axes, 2.4G
rms 5Hz to 500Hz.

For optimum reliability, no part of the heatsink should exceed 110

C, and

no semiconductor case temperature should exceed 120

CAUTION: Allow a minimum of 1 second after disconnecting line power
when making thermal measurements.

This product is only for inclusion by professional installers within other
equipment and must not be operated as a stand alone product.

The EMI specifications reference measurements made with the power
supply mounted on a grounded metal sheet extending 1 inch beyond
each edge, using an unshielded cable. No external filtering required
during conducted emissions testing but some applications may require
additional filtering to achieve system compliance. A line choke, (AC input
cords looped twice through an EMI suppression toroid) was used during
radiated emissions testing. Considerable radiated testing in 1U six-sided
boxes has shown that units can meet level B in typical systems.
Application support is available from the factory to assist with EMI
compliance.

All models require a minimum mounting stand-off of 6.35mm (0.25
inches) in the end use product.

NLP110 Medical Series

S i n g l e a n d t r i p l e o u t p u t

LOW TO MEDIUM POWER AC/DC POWER SUPPLIES 80-110W AC/DC Universal Input Switch Mode Power Supplies

www.artesyn.com

File Name: NLP110M.PDF Rev: 13 Dec 2002

International Safety Standard Approvals

VDE0750/IEC60601-1 and EN60601-1

UL2601-1 and C22.2 No. 601.1-M90.

OUTPUT

OUTPUT CURRENT

RIPPLE

(5)

TOTAL

MODEL

VOLTAGE

MIN

(6)

MAX

(1)

150LFM

(2)

300LFM

(3)

PEAK

(4)

REGULATION

NUMBERS

+5V

0.5A

15A

22A

50mV

±2.0%

NLP110-9905

+12V

0.3A

6.4A

9.2A

11.5A

120mV

±2.0%

NLP110-9912

+48V

1.6A

2.3A

2.5A

240mV

±2.0%

NLP110-9917

+24V

0.2A

3.2A

4.6A

6.0A

240mV

±2.0%

NLP110-9924

+5V (A)

0.5A

13A

16A

18A

50mV

±2.0%

NLP110-9993

+3.3V (B)

0.2A

13A

16A

20A

50mV

±2.0%

+12V

0.65A

1.0A

120mV

±5.0%

+3.3V (A)

0.5A

13A

16A

20A

22A

50mV

±2.0%

NLP110-9994

+2.5V (B)

0.1A

13A

16A

20A

22A

50mV

±2.0%

+12V

0.65A

1.0A

120mV

±5.0%

+12V (A)

0.2A

6.5A

8.5A

10A

1200mV

±2.0%

NLP110-9995

(7)

+3.3V (B)

0.5A

13A

16A

20A

22A

50mV

±2.0%

-12V

0.65A

1.0A

120mV

±5.0%

+12V (A)

0.2A

6.5A

8.5A

10A

120mV

±2.0%

NLP110-9908

(7)

+5V (B)

0.2A

13A

16A

18A

22A

50mV

±2.0%

-12V

0.65A

1.0A

120mV

±5.0%

DERATING CURVE

Output Power (Watts)

°C 10°C20°C30°C40°C50°C60°C 70°C

40W

80W

110W

150 LFM FORCED

AIR COOLING

55W

NATURAL

CONVECTION

COOLING

Input and output connectors

Mating connectors

AC (J1) connector type

AC (J1) mating connector type

Molex 26-60-4030 or equivalent.

Molex 09-50-3031 or equivalent with Molex
08-50-0105 or equivalent crimp terminals.

DC (J2) connector type

DC (J2) mating connector type

12 position Molex Spox type 26-48-1125

Molex Spox type 26-03-3121 and

or equivalent.

contact 08-52-0113.

Sense (J3) connector type

Sense (J3) mating connector type

Molex 22-23-2021 or equivalent.

Molex 22-01-3027 and contact
08-50-0113.

Earth (J4) connector type

Earth (J4) mating connector type

Male 0.250 quick disconnect.

Molex 90028.

Sense (J5) connector type

Sense (J5) mating connector type

Leoco 2421P02H000.

Leoco 2420S020000 and contact
2453TPB00V1.

0.23

(5.842)

6.50

(165.10)

T1 (REF.)

6.050

(153.670)

2.550

(64.770)

ALL DIMENSIONS IN INCHES (mm)

3.00

(76.20)

0.23

(5.842)

MAXIMUM COMPONENT
HEIGHT IS 1.26 (32.00)

OUTPUT PIN CONNECTIONS

SINGLE

TRIPLE

Pin 1

No Connection

V (B)

Pin 2

No Connection

V (B)

Pin 3

No Connection

V (B)

Pin 4

Return

Pin 5

Return

Pin 6

Return

Pin 7

Return

Pin 8

V (A)

Pin 9

V (A)

Pin 10

V (A)

Pin 11

No Connection

V (C)

Pin 12

No Connection

V (C) Return

(7)

Recommended direction
for forced air relative to
power supply orientation
shown below.

Optimum.

Very good.

Good.

Not recommended.

INPUT

PIN CONNECTIONS

Pin 1

AC Neutral

Pin 2

No Connection

Pin 3

AC Line

Pin 1

V (A) Sense +

Pin 2

V (A) Sense -

Pin 1

Safety Earth

Pin 1

V (B) Sense +

Pin 2

V (B) Sense -

Data Sheet © Artesyn Technologies® 2002
The information and specifications contained in this data sheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising
from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein.

For the most current data and application support visit www.artesyn.com/powergroup/products.htm

NLP110 Medical Series

S i n g l e a n d t r i p l e o u t p u t

LOW TO MEDIUM POWER AC/DC POWER SUPPLIES 80-110W AC/DC Universal Input Switch Mode Power Supplies

www.artesyn.com

File Name: NLP110M.PDF Rev: 13 Dec 2002

Mechanical Notes

All dimensions are in inches (mm).

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: NLP110-9917

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: NLP110-9917