Document No. 485LP9TBN4500 - pg. 1/2
1995 B&B Electronics Revised November 2000
This product designed and manufactured in USA of domestic and imported parts by
Port Powered RS-232 to RS-485 Converter
CE
Model 485LP9TBN
The 485LP9TBN is a port-powered two-channel RS-232 to RS-485
converter. It converts TD and RD RS-232 lines to balanced RS-485 signals.
The unit can be powered from the RS-232 handshake lines, DTR and RTS. One of these handshakes must be high
(asserted) to power the unit (See Table 1). DTR must be asserted to receive data. The RS-485 driver is enabled when
RTS is asserted and disabled when RTS is disasserted. The RS-485 receiver is disabled when the driver is enabled and is
enabled when the driver is disabled.
In order to maximize the amount of power available to the RS-485 driver, the RS-232 handshake lines are not
looped back (tied together). As a result the following handshake lines will appear as disasserted (low): CTS, DCD, and
DSR. Care should be taken to insure that any software being used doesn't require any of these handshake lines be
asserted. If existing software requires any of the handshake lines to be asserted, you can loop back the required
handshake lines in your cable.
Table 1
* NOTE: Low = disasserted and High = asserted
Connections
A typical two wire RS-485 connected is shown in Figure 1. Regardless of the system, the 485LP9TBN must be
connected with the proper polarity. With no data is being sent and the driver enabled, the RS-232 line should be negative
and the TD(A) should be negative with respect to TD(B).
Proper operation of any RS-485 system requires the presence of a signal return path between the signal grounds of
the equipment at each end of an interconnection. This circuit reference may be established by a third conductor
connecting the common leads of devices, or it may be provided by connections in each equipment to an earth reference.
When the circuit reference is provided by a third conductor, the connection between the signal grounds and the third
conductor should contain some resistance (e.g. 100 ohms) to limit circulating currents when other ground connections are
provided for safety.
RTS State
DTR State
Functions Possible
(when port powering unit)
Low
Low
none
Low
High
Receive
High
Low
Transmit
High
High
Transmit
Document No. 485LP9TBN4500 - pg. 2/2
1995 B&B Electronics Revised November 2000
This product designed and manufactured in USA of domestic and imported parts by
Biasing Resistors
The biasing resistors for the RS-422/RS-485 receiver are 4.7K Ohm resistors. These resistors are labeled R1 and R6
(See Figure 2). Refer to B&B Electronics RS-422/485 Application Note for further information on biasing.
Specifications
Data Rate: 115.2K Baud max.
Power:
Port Powered from RTS and DTR.
NOTE: If external power is required, use a source that can supply 12 to 16VDC at 40mA
NOTE: When using an external supply, the supply should be connected only to specifically labeled power inputs
(power jack, terminal block, etc.). Connecting an external power supply to the handshake lines may damage the
unit. Contact technical support for more information on connecting an external power supply to the handshake
lines.
DECLARATION OF CONFORMITY
Manufacturer's Name:
B&B Electronics Manufacturing Company
Manufacturer's Address:
P.O. Box 1040
707 Dayton Road
Ottawa, IL 61350 USA
Model Numbers:
485LP9TBN
Description:
Port-Powered RS-232 to RS-485 Converter
Type:
Light industrial ITE equipment
Application of Council Directive:
89/336/EEC
Standards:
EN 50082-1 (IEC 801-2, IEC 801-3, IEC 801-4)
EN 50081-1 (EN 55022, IEC 1000-4-2)
EN 61000 (-4-2, -4-3, -4-4, -4-5, -4-6, -4-8, -4-11)
ENV 50204
EN 55024
Michael J. Fahrion, Director of Engineering
PDF 
ZIP