R0201-BS62LV2565
Revision 2.2
April 2001
1
A6
Very Low Power/Voltage CMOS SRAM
32K X 8 bit
Wide Vcc operation voltage : 4.5V ~ 5.5V
Very low power consumption :
Vcc = 5.0V C-grade : 35mA (Max.) operating current
I- grade : 40mA (Max.) operating current
0.4uA (Typ.) CMOS standby current
High speed access time :
-55 55ns (Max.) = 5.0V
-70 70ns (Max.) = 5.0V
Automatic power down when chip is deselected
Three state outputs and TTL compatible
Fully static operation
Data retention supply voltage as low as 1.5V
Easy expansion with CE and OE options
The BS62LV2565 is a high performance, very low power CMOS
Static Random Access Memory organized as 32,768 words by 8 bits
and operates from a wide range of 4.5V to 5.5V supply voltage.
Advanced CMOS technology and circuit techniques provide both high
speed and low power features with a typical CMOS standby current of
0.4uA and maximum access time of 55ns in 5V operation.
Easy memory expansion is provided by an active LOW chip
enable (CE), and active LOW output enable (OE) and three-state
output drivers.
The BS62LV2565 has an automatic power down feature, reducing the
power consumption significantly when chip is deselected.
The BS62LV2565 is available in the JEDEC standard 28 pin
330mil Plastic SOP, 300mil Plastic SOJ, 600mil Plastic DIP and
8mmx13.4mm TSOP (normal type).
DESCRIPTION
FEATURES
BLOCK DIAGRAM
PRODUCT FAMILY
PIN CONFIGURATIONS
Brilliance Semiconductor Inc
. reserves the right to modify document contents without notice.
Address
Input
Buffer
Row
Decoder
Memory Array
512 x 512
Column I/O
Sense Amp
Write Driver
Column Decoder
Data
Buffer
Output
Address Input Buffer
A3 A2 A1 A0 A10
Data
Buffer
Input
Control
Gnd
Vdd
OE
WE
CE
DQ5
DQ4
A12
A8
A7
8
8
8
8
DQ7
DQ6
DQ3
DQ2
DQ1
DQ0
A11
A9
A5
12
64
512
512
18
A14
A13
A4
28
27
26
25
24
23
22
21
20
19
18
17
16
15
A10
CE
DQ7
DQ6
DQ5
DQ4
DQ3
GND
DQ2
DQ1
DQ0
A0
A1
A2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
OE
A11
A9
A8
A13
WE
VCC
A14
A12
A7
A6
A5
A4
A3
BS62LV2565
A14
A12
A7
A6
A5
A4
A3
A2
A1
A0
DQ0
DQ1
DQ2
GND
VC
WE
A13
A8
A9
A11
OE
A10
CE
DQ7
DQ6
DQ5
DQ4
DQ3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
C
BS62LV2565TC
BS62LV2565TI
BS62LV2565SC
BS62LV2565SI
BS62LV2565PC
BS62LV2565PI
BS62LV2565JC
BS62LV2565JI
POWER DISSIPATION
SPEED
(ns)
STANDBY
(I
CCSB1
, Max)
Operating
(I
CC
, Max)
PRODUCT
FAMILY
Vcc
RANGE
Vcc=5.0V
Vcc=5.0V
Vcc=5.0V
PKG
TYPE
BS62LV2565SC
SOP-28
BS62LV2565TC
TSOP-28
BS62LV2565PC
PDIP-28
BS62LV2565JC
SOJ-28
BS62LV2565DC
0
O
C to +70
O
C
4.5V ~ 5.5V
55 / 70
1.0uA
35mA
DICE
BS62LV2565SI
SOP-28
BS62LV2565TI
TSOP-28
BS62LV2565PI
PDIP-28
BS62LV2565JI
SOJ-28
BS62LV2565DI
-40
O
C to +85
O
C
4.5V ~ 5.5V
55 / 70
2.0uA
40mA
DICE
BSI
OPERATING
TEMPERATURE
R0201-BS62LV2565
Revision 2.2
April 2001
2
BSI
SYMBOL
PARAMETER
CONDITIONS
MAX.
UNIT
C
IN
Input
Capacitance
V
IN
=0V
6
pF
C
DQ
Input/Output
Capacitance
V
I/O
=0V
8
pF
ABSOLUTE MAXIMUM RATINGS
(1)
OPERATING RANGE
CAPACITANCE
(1)
(TA = 25
o
C, f = 1.0 MHz)
1. Stresses greater than those listed under ABSOLUTE MAXIMUM
RATINGS may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at these
or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
reliability.
1. This parameter is guaranteed and not tested.
SYMBOL
PARAMETER
RATING
UNITS
V
TERM
Terminal Voltage with
Respect to GND
-0.5 to +6.0
V
T
BIAS
Temperature Under Bias
-40 to +125
O
C
T
STG
Storage Temperature
-60 to +150
O
C
P
T
Power Dissipation
1.0
W
I
OUT
DC Output Current
mA
20
BS62LV2565
RANGE
AMBIENT
TEMPERATURE
Vcc
Commercial
0
O
C to +70
O
C
4.5V ~ 5.5V
Industrial
-40
O
C to +85
O
C
4.5V ~ 5.5V
Name
Function
A0-A14 Address Input
These 15 address input select one of the 32768 x 8-bit wordsin the RAM
CE Chip Enable Input
CE is active LOW. Chip enables must be active to read from or write to the device. If
chip enable is not active, the device is deselected and is in a standby power mode.
The DQ pins will be in the high impedance state when the device is deselected.
WE Write Enable Input
The write enable input is active LOW and controls read and write operations. With the
chip selected, when WE is HIGH and OE is LOW, output data will be present on the
DQ pins; when WE is LOW, the data present on the DQ pins will be written into the
selected memory location.
OE Output Enable Input
The output enable input is active LOW. If the output enable is active while the chip is
selected and the write enable is inactive, data will be present on the DQ pins and they
will be enabled. The DQ pins will be in the high impedance state when OE is inactive.
DQ0-DQ7 Data Input/Output
Ports
These 8 bi-directional ports are used to read data from or write data into the RAM.
Vcc
Power Supply
Gnd
Ground
MODE
WE
CE
OE
I/O OPERATION
Vcc CURRENT
Not selected
X
H
X
High Z
I
CCSB
, I
CCSB1
Output Disabled
H
L
H
High Z
I
CC
Read
H
L
L
D
OUT
I
CC
Write
L
L
X
D
IN
I
CC
TRUTH TABLE
PIN DESCRIPTIONS
R0201-BS62LV2565
Revision 2.2
April 2001
3
PARAMETER
NAME
PARAMETER
TEST CONDITIONS
MIN. TYP.
(1)
MAX.
UNITS
V
IL
Guaranteed Input Low
Voltage
(2)
Vcc=5.0V
-0.5 -- 0.8 V
V
IH
Guaranteed Input High
Voltage
(2)
Vcc=5.0V
2.2 --
Vcc+0.2
V
I
IL
Input Leakage Current
Vcc = Max, V
IN
= 0V to Vcc
--
--
1
uA
I
OL
Output
Leakage
Current
Vcc = Max, CE = V
IH
, or OE = V
IH
,
V
I/O
= 0V to Vcc
-- -- 1 uA
V
OL
Output Low Voltage
Vcc = Max, I
OL
= 2mA
Vcc=5.0V
-- -- 0.4 V
V
OH
Output High Voltage
Vcc = Min, I
OH
= -1mA
Vcc=5.0V
2.4 -- -- V
I
CC
Operating Power
Supply Current
CE = V
IL
, I
DQ
= 0mA, F = Fmax
(3)
Vcc=5.0V
--
--
35
mA
I
CCSB
Standby Current-TTL
CE = V
IH
, I
DQ
= 0mA
Vcc=5.0V
--
--
2
mA
I
CCSB1
Standby
Current-CMOS
CE
Vcc-0.2V,
V
IN
Vcc - 0.2V or V
IN
0.2V
Vcc=5.0V
--
0.4 1.0
uA
DC ELECTRICAL CHARACTERISTICS
( TA = 0
o
C to + 70
o
C )
BSI
BS62LV2565
SYMBOL
PARAMETER
TEST CONDITIONS
MIN. TYP.
(1)
MAX.
UNITS
V
DR
Vcc for Data Retention
CE
Vcc - 0.2V
V
IN
Vcc - 0.2V or V
IN
0.2V
1.5
--
--
V
I
CCDR
Data Retention Current
CE
Vcc -0.2V
V
IN
Vcc - 0.2V or V
IN
0.2V
--
0.01
0.40
uA
t
CDR
Chip Deselect to Data
Retention Time
0
--
--
ns
t
R
Operation Recovery Time
See Retention Waveform
T
RC
(2)
--
--
ns
DATA RETENTION CHARACTERISTICS
( TA = 0
o
C to + 70
o
C )
1. Vcc = 1.5V, T
A
= + 25
O
C
2. t
RC
= Read Cycle Time
LOW V
CC
DATA RETENTION WAVEFORM (1)
( CE Controlled )
CE
Data Retention Mode
Vcc
t
CDR
Vcc
t
R
V
IH
V
IH
Vcc
V
DR
1.5V
CE Vcc - 0.2V
1. Typical characteristics are at TA = 25
o
C.
2. These are absolute values with respect to device ground and all overshoots due to system or tester notice are included.
3. Fmax = 1/t
RC
.
R0201-BS62LV2565
Revision 2.2
April 2001
4
JEDEC
PARAMETER
NAME
PARAMETER
NAME
DESCRIPTION
BS62LV2565-55
MIN. TYP. MAX.
BS62LV2565-70
MIN. TYP. MAX.
UNIT
t
AVAX
t
RC
Read Cycle Time
55
--
--
70
--
--
ns
t
AVQV
t
AA
Address Access Time
--
--
55
--
--
70
ns
t
ELQV
t
ACS
Chip Select Access Time
--
--
55
--
--
70
ns
t
GLQV
t
OE
Output Enable to Output Valid
--
--
25
--
--
35
ns
t
ELQX
t
CLZ
Chip Select to Output Low Z
10
--
--
10
--
--
ns
t
GLQX
t
OLZ
Output Enable to Output in Low Z
10
--
--
10
--
--
ns
t
EHQZ
t
CHZ
Chip Deselect to Output in High Z
0
--
30
0
--
35
ns
t
GHQZ
t
OHZ
Output Disable to Output in High Z
0
--
25
0
--
30
ns
t
AXOX
t
OH
Output Disable to Output Address Change
10
--
--
10
--
--
ns
Input Pulse Levels
Input Rise and Fall Times
Input and Output
Timing Reference Level
Vcc/0V
5ns
0.5Vcc
AC ELECTRICAL CHARACTERISTICS
( TA = 0
o
C to + 70
o
C, Vcc=5V )
READ CYCLE
AC TEST CONDITIONS
AC TEST LOADS AND WAVEFORMS
KEY TO SWITCHING WAVEFORMS
WAVEFORM
INPUTS
OUTPUTS
MUST BE
STEADY
MAY CHANGE
FROM H TO L
DON T CAR
ANY CHANG
PERMITTED
E:
CHANGE :
E
STATE
DOES NOT
APPLY
MUST BE
STEADY
WILL BE
CHANGE
FROM H TO L
UNKNOWN
CENTER
LINE IS HIGH
IMPEDANCE
"OFF "STATE
MAY CHANGE
FROM L TO H
WILL BE
CHANGE
FROM L TO H
,
667
THEVENIN EQUIVALENT
ALL INPUT PULSES
10%
90%
Vcc
GND
5ns
90%
10%
1.73V
OUTPUT
FIGURE 2
5.0V
OUTPUT
INCLUDING
JIG AND
SCOPE
1928
1020
5PF
FIGURE 1B
5.0V
OUTPUT
INCLUDING
JIG AND
SCOPE
1928
100PF
FIGURE 1A
1020
BSI
BS62LV2565
R0201-BS62LV2565
Revision 2.2
April 2001
5
BSI
BS62LV2565
SWITCHING WAVEFORMS (READ CYCLE)
READ CYCLE1
(1,2,4)
t
RC
t
OH
t
AA
D
OUT
ADDRESS
t
OH
READ CYCLE3
(1,4)
READ CYCLE2
(1,3,4)
NOTES:
1. WE is high in read Cycle.
2. Device is continuously selected when CE = V
IL
.
3. Address valid prior to or coincident with CE transition low.
4. OE = V
IL
.
5. Transition is measured 500mV from steady state with C
L
= 5pF as shown in Figure 1B.
The parameter is guaranteed but not 100% tested.
t
CLZ
t
CHZ
(5)
D
OUT
CE
(5)
t
ACS
t
OH
t
RC
t
OE
D
OUT
CE
OE
ADDRESS
t
CLZ
(5)
t
ACS
t
CHZ
(1,5)
t
OHZ
(5)
t
OLZ
t
AA
PDF 
ZIP