1
DCV01
Miniature, 1W, 1500Vrms Isolated
UNREGULATED DC/DC CONVERTERS
2000 Burr-Brown Corporation
PDS-1592B
Printed in U.S.A. August, 2000
DCV01
Series
International Airport Industrial Park Mailing Address: PO Box 11400, Tucson, AZ 85734 Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 Tel: (520) 746-1111
Twx: 910-952-1111 Internet: http://www.burr-brown.com/ Cable: BBRCORP Telex: 066-6491 FAX: (520) 889-1510 Immediate Product Info: (800) 548-6132
FEATURES
q
UP TO 85% EFFICIENCY
q
THERMAL PROTECTION
q
DEVICE-TO-DEVICE SYNCHRONIZATION
q
SHORT-CIRCUIT PROTECTION
q
EN55022 CLASS B EMC PERFORMANCE
q
UL1950 RECOGNIZED COMPONENT
q
JEDEC PDIP-14 AND GULL-WING PACKAGES
DESCRIPTION
The DCV01 series is a family of 1W, 1500Vrms
isolated, unregulated DC/DC converters. Requiring a
minimum of external components and including on-
chip device protection, the DCV01 series provides
extra features such as output disable and synchroniza-
tion of switching frequencies.
The use of a highly integrated package design results
in highly reliable products with a power density of
40W/in
3
(2.4W/cm
3
). This combination of features,
high isolation, and small size makes the DCV01 suit-
able for a wide range of applications.
APPLICATIONS
q
INDUSTRIAL CONTROL AND
INSTRUMENTATION
q
POINT-OF-USE POWER CONVERSION
q
GROUND LOOP ELIMINATION
q
DATA ACQUISITION
q
TEST EQUIPMENT
q
SECONDARY ISOLATION CIRCUITS
For most current data sheet and other product
information, visit www.burr-brown.com
I
BIAS
Power
Stage
V
OUT
2
Reset
800kHz
Oscillator
Watch-dog/
start-up
PSU
Thermal
Shutdown
SYNC
OUT
SYNC
IN
V
S
0V
Power Controller IC
0V
DCV01
DCV01
SBVS014
2
DCV01
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the user's own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.
INPUT
OUTPUT
LOAD
NO LOAD
BARRIER
LEAKAGE
VOLTAGE (V)
VOLTAGE (V)
REGULATION (%)
CURRENT (mA)
EFFICIENCY (%)
CAPACITANCE (pF)
CURRENT (
A)
V
S
V
NOM
I
Q
C
ISO
75% LOAD
(2)
10% TO 100% LOAD
(3)
0% LOAD
100% LOAD
V
ISO
= 750Vrms
V
ISO
= 750Vrms
PRODUCT
MIN
TYP
MAX
MIN
TYP
MAX
TYP
MAX
TYP
TYP
TYP
TYP
DCV010505
4.5
5
5.5
4.75
5
5.25
23
31
20
78
3.6
0.9
DCV010505D
(4)
4.5
5
5.5
4.75
5
5.25
19
32
23
80
3.8
0.9
DCV010512
4.5
5
5.5
11.4
12
12.6
23
38
30
85
5.1
1.2
DCV010512D
4.5
5
5.5
11.4
12
12.6
19
37
40
82
4.0
1.0
DCV010515
4.5
5
5.5
14.25
15
15.75
30
42
34
84
3.8
0.9
DCV010515D
4.5
5
5.5
14.25
15
15.75
27
41
42
85
4.7
1.1
DCV011512D
(4)
13.5
15
16.5
11.4
12
12.6
11
39
19
78
4.2
1.0
DCV011515D
(4)
13.5
15
16.5
14.25
15
15.75
12
39
20
79
4.2
1.0
DCV012405
(4)
21.6
24
26.4
4.75
5
5.25
13
23
14
77
3.8
0.9
DCV012415D
(4)
21.6
24
26.4
14.25
15
15.75
12
35
17
76
5.3
1.3
NOTES: (1) During UL1950 recognition tests only, UL File #E199929. (2) 100% Load Current = 1W/V
NOM
TYP. (3) Load regulation = (V
OUT
at 10% V
OUT
at 100%)/ V
OUT
at 75%. (4) Scheduled availability
Q4 2000.
SPECIFICATIONS
At T
A
= +25
C, unless otherwise specified.
DCV01 SERIES
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
OUTPUT
Power
100% Full Load
0.97
W
Ripple
O/P Capacitor = 1
F, 50% Load
20
mVp-p
Voltage vs Temp
Room to Cold
0.046
%/
C
Room to Hot
0.016
%/
C
INPUT
Voltage Range on V
S
10
10
%
ISOLATION
Voltage
1s Flash Test
1.5
kVrms
60s Test, UL1950
(1)
1.5
kVrms
LINE
Regulation
1
%/1% of V
S
SWITCHING/SYNCHRONIZATION
Oscillator Frequency (f
OSC
)
Switching Frequency = f
OSC
/2
800
kHz
Sync Input Low
0
0.4
V
Sync Input Current
V
SYNC
= +2V
75
A
Disable Time
2
s
Capacitance Loading on SYNC
IN
Pin
External
3
pF
RELIABILITY
Demonstrated
T
A
= +55
C
75
FITS
THERMAL SHUTDOWN
IC Temperature at Shutdown
150
C
Shutdown Current
3
mA
TEMPERATURE RANGE
Operating
40
+85
C
3
DCV01
Basic Model Number: 1W Product
Voltage Input:
5V In
Voltage Output:
5V Out
Dual Output:
Package Code:
P = PDIP-14
P-U = PDIP-14 Gull-Wing
05
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degrada-
tion to complete device failure. Precision integrated circuits
may be more susceptible to damage because very small
parametric changes could cause the device not to meet its
published specifications.
Input Voltage:
5V Input Models .................................................................................. 7V
15V Input Models .............................................................................. 18V
24V Input Models .............................................................................. 29V
Storage Temperature ...................................................... 60
C to +125
C
Lead Temperature (soldering, 10s) ................................................. 270
C
ABSOLUTE MAXIMUM RATINGS
ORDERING INFORMATION
05
(
)
( D )
PACKAGE
SPECIFIED
DRAWING
TEMPERATURE
PACKAGE
ORDERING
TRANSPORT
PRODUCT
PACKAGE
NUMBER
RANGE
MARKING
NUMBER
(1)
MEDIA
Single
DCV010505P
DIP-14
010-1
40
C to +85
C
DCV010505P
DCV010505P
Rails
DCV010505P-U
Gull-Wing-14
010-2
40
C to +85
C
DCV010505P-U
DCV010505P-U/700
Tape and Reel
DCV010512P
DIP-14
010-1
40
C to +85
C
DCV010512P
DCV010512P
Rails
DCV010512P-U
Gull-Wing-14
010-2
40
C to +85
C
DCV010512P-U
DCV010512P-U/700
Tape and Reel
DCV010515P
DIP-14
010-1
40
C to +85
C
DCV010515P
DCV010515P
Rails
DCV010515P-U
Gull-Wing-14
010-2
40
C to +85
C
DCV010515P-U
DCV010515P-U/700
Tape and Reel
DCV012405P
(2)
DIP-14
010-1
40
C to +85
C
DCV012405P
DCV012405P
Tape and Reel
DCV012405P-U
(2)
Gull-Wing-14
010-2
40
C to +85
C
DCV012405P-U
DCV012405P-U/700
Rails
Dual
DCV010505DP
(2)
DIP-14
010-1
40
C to +85
C
DCV010505DP
DCV010505DP
Rails
DCV010505DP-U
(2)
Gull-Wing-14
010-2
40
C to +85
C
DCV010505DP-U
DCV010505DP-U/700
Tape and Reel
DCV010512DP
DIP-14
010-1
40
C to +85
C
DCV010512DP
DCV010512DP
Rails
DCV010512DP-U
Gull-Wing-14
010-2
40
C to +85
C
DCV010512DP-U
DCV010512DP-U/700
Tape and Reel
DCV010515DP
DIP-14
010-1
40
C to +85
C
DCV010515DP
DCV010515DP
Rails
DCV010515DP-U
Gull-Wing-14
010-2
40
C to +85
C
DCV010515DP-U
DCV010515DP-U/700
Tape and Reel
DCV011512DP
(2)
DIP-14
010-1
40
C to +85
C
DCV011512DP
DCV011512DP
Rails
DCV011512DP-U
(2)
DIP-14
010-2
40
C to +85
C
DCV011512DP-U
DCV011512DP-U/700
Tape and Reel
DCV011515DP
(2)
Gull-Wing-14
010-1
40
C to +85
C
DCV011515DP
DCV011515DP
Rails
DCV011515DP-U
(2)
DIP-14
010-2
40
C to +85
C
DCV011515DP-U
DCV011515DP-U/700
Tape and Reel
DCV012415DP
(2)
Gull-Wing-14
010-1
40
C to +85
C
DCV012415DP
DCV012415DP
Rails
DCV012415DP-U
(2)
DIP-14
010-2
40
C to +85
C
DCV012415DP-U
DCV012415DP-U/700
Tape and Reel
NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /700 indicates 700 devices per reel). Ordering 700 pieces
of "DCP010505BP-U/700" will get a single 700-piece Tape and Reel. (2) Scheduled availability Q4 2000.
PACKAGE/ORDERING INFORMATION
DCV01
4
DCV01
Top View
DIP
PIN CONFIGURATION (Single-DIP and Gull-Wing)
Top View
DIP
PIN CONFIGURATION (Dual-DIP and Gull-Wing)
PIN DEFINITION (Single-DIP)
PIN #
PIN NAME
DESCRIPTION
1
V
S
Voltage Input
2
0V
Input Side Common
5
0V
Output Side Common
6
+V
OUT
+Voltage Out
7
NC
Not Connected
8
SYNC
OUT
Unrectified Transformer Output
14
SYNC
IN
Synchronization Pin
PIN DEFINITION (Dual-DIP)
PIN #
PIN NAME
DESCRIPTION
1
V
S
Voltage Input
2
0V
Input Side Common
5
0V
Output Side Common
6
+V
OUT
+Voltage Out
7
V
OUT
Voltage Out
8
SYNC
OUT
Unrectified Transformer Output
14
SYNC
IN
Synchronization Pin
DCV01D
1
2
5
6
7
14
8
V
S
0V
0V
+V
OUT
V
OUT
SYNC
IN
SYNC
OUT
DCV01
1
2
5
6
7
14
8
V
S
0V
0V
+V
OUT
NC
SYNC
IN
SYNC
OUT
5
DCV01
TYPICAL PERFORMANCE CURVES
At T
A
= +25
C, unless otherwise noted.
DCV010505
OUTPUT RIPPLE vs LOAD (20MHz BW)
Load (%)
Ripple (mVp-p)
50
45
40
35
30
25
20
15
10
5
0
20
30
50
70
60
80
90
100
40
10
1
F Ceramic
4.7
F Ceramic
10
F Ceramic
DCV010512D V
OUT
vs LOAD
Load (%)
V
OUT
(V)
14.5
14.0
13.5
13.0
12.5
12.0
11.5
11.0
10.5
10.00
20
30
50
70
60
80
90
100
40
10
+V
OUT
V
OUT
DCV010512D EFFICIENCY vs LOAD
Load (%)
Ef
ficiency (%)
85
80
75
70
65
60
55
50
20
30
50
70
60
80
90
100
40
10
DCV010515D V
OUT
vs LOAD
Load (%)
V
OUT
(V)
18
17
16
15
14
20
30
50
70
60
80
90
100
40
10
+V
OUT
V
OUT
DCV010515D EFFICIENCY vs LOAD
Load (%)
Ef
ficiency (%)
90
85
80
75
70
65
60
55
50
20
30
50
70
60
80
90
100
40
10
DCV012405 V
OUT
vs LOAD
Load (%)
V
OUT
(V)
5.60
5.50
5.40
5.30
5.20
5.10
5.00
4.90
4.80
20
30
60
50
70
80
100
40
10
6
DCV01
TYPICAL PERFORMANCE CURVES
(Cont.)
At T
A
= +25
C, unless otherwise noted.
DCV012405 EFFICIENCY vs LOAD
Load (%)
Ef
ficiency (%)
90
80
70
60
50
40
30
20
10
0
20
30
70
60
80
90
100
40
50
10
DCV010505
CONDUCTED EMISSIONS (125% Load)
Emission Level, Peak (dB
A)
Frequency (MHz)
1
0.15
10
30
60
50
40
30
20
10
0
10
20
DCV010505
CONDUCTED EMISSIONS (8% Load)
Emission Level, Peak (dB
A)
Frequency (MHz)
1
0.15
10
30
60
50
40
30
20
10
0
10
20
7
DCV01
FIGURE 1. Connecting the DCV01 in Series.
FUNCTIONAL DESCRIPTION
OVERVIEW
The DCV01 offers up to 1W of unregulated output power
with a typical efficiency of up to 85%. This is achieved
through highly integrated packaging technology and the
implementation of a custom power stage and control IC. The
circuit design utilizes an advanced BiCMOS/DMOS pro-
cess. Separate primary and secondary transformer windings
give good isolation and low barrier capacitance.
POWER STAGE
This uses a push-pull, center-tapped topology switching at
400kHz (divide by 2 from 800kHz oscillator).
OSCILLATOR AND WATCHDOG
The onboard 800kHz oscillator generates the switching
frequency via a divide by 2 circuit. The oscillator can be
synchronized to other DCV01 circuits or an external source,
and is used to minimize system noise.
A watchdog circuit checks the operation of the oscillator
circuit. The oscillator can be stopped by pulling the SYNC
IN
pin LOW. The output pins will be tri-stated. This will occur
in 2
s.
THERMAL SHUTDOWN
The DCV01 is protected by a thermal shutdown circuit. If the
on-chip temperature exceeds 150
C, the device will shut
down. Once the temperature falls below 150
C, normal
operation will resume.
SYNCHRONIZATION
In the event that more than one DC/DC converter is needed
onboard, beat frequencies and other electrical interference
can be generated. This is due to the small variations in
switching frequencies between the DC/DC converters.
The DCV01 overcomes this by allowing devices to be
synchronized to one another. Up to eight devices can be
synchronized by connecting the SYNC
IN
pins together, tak-
ing care to minimize the capacitance of tracking. Stray
capacitance (> 3pF) will have the effect of reducing the
switching frequency, or even stopping the oscillator circuit.
If synchronized devices are used, it should be noted that, at
start up, all devices will draw maximum current simulta-
neously. This can cause the input voltage to dip and should
it dip below the minimum input voltage (4.5V), the devices
may not start up. A 2.2
F capacitor should be connected
close to the input pins.
If more than eight devices are to be synchronized, it is
recommended that the SYNC
IN
pins are driven by an exter-
nal device. Details are contained in a separate applications
bulletin (AB-153).
CONSTRUCTION
The DCV01's basic construction is the same as standard ICs.
There is no substrate within the molded package. The
DCV01 is constructed using an IC, rectifier diodes, and a
wound magnetic toroid on a leadframe. As there is no solder
within the package, the DCV01 does not require any special
PCB assembly processing. This results in an isolated
DC/DC converter with inherently high reliability.
ADDITIONAL FUNCTIONS
DISABLE/ENABLE
The DCV01 can be disabled or enabled by driving the SYNC
pin using an open drain CMOS gate. If the SYNC
IN
pin is
pulled low, the DCV01 will be disabled. The disable time
depends upon the external loading; the internal disable func-
tion is implemented in 2
s. Removal of the pull down will
cause the DCV01 to be enabled.
Capacitive loading on the SYNC
IN
pin should be minimized
in order to prevent a reduction in the oscillator frequency.
DECOUPLING
Ripple Reduction
The high switching frequency of 400kHz allows simple
filtering. To reduce ripple, it is recommended that at least a
1
F capacitor is used on V
OUT
. Dual outputs should both be
decoupled to pin 5. A 2.2
F low ESR capacitor on the input
of the 5V in versions, and a 0.47
F low ESR cap on the 24V
DCV01 in versions is recommended.
DCV
01
V
OUT 1
V
SUPPLY
V
S
0V
DCV
01
V
OUT 2
V
OUT1
+ V
OUT 2
SYNC
IN
SYNC
IN
V
S
0V
0V
0V
COM
8
DCV01
FIGURE 2. Connecting Dual Outputs in Series.
Connecting the DCV01 in Series
Multiple DCV01 isolated 1W DC/DC converters can be
connected in series to provide nonstandard voltage rails.
This is possible by utilizing the floating outputs provided by
the DCV01's galvanic isolation.
Connect the positive V
OUT
from one DCV01 to the negative
V
OUT
(0V) of another (see Figure 1). If the SYNC
IN
pins are
tied together, the self-synchronization feature of the DCV01
will prevent beat frequencies on the voltage rails. The
SYNC
IN
feature of the DCV01 allows easy series connec-
tion without external filtering, minimizing cost.
The outputs on dual output DCV01 versions can also be
connected in series to provide two times the magnitude of
V
OUT
as shown in Figure 2. For example, a dual 15V DCV01
could be connected to provide a 30V rail.
Connecting the DCV01 in Parallel
If the output power from one DCV01 is not sufficient, it is
possible to parallel the outputs of multiple DCV01s, as
shown in Figure 3. Again, the SYNC
IN
feature allows easy
synchronization to prevent power-rail beat frequencies at no
additional filtering cost.
PCB LAYOUT
Ripple and Noise
Careful consideration should be given to the layout of the
PCB in order that the best results can be obtained.
The DCV01 is a switching power supply and as such can
place high peak current demands on the input supply. In
order to avoid the supply falling momentarily during the fast
switching pulses ground and power planes should be used to
track the power to the input of DCV01. If this is not possible
then the supplies must be connected in a star formation with
the tracks made as wide as possible.
If the SYNC
IN
pin is being used then the tracking between
device SYNC
IN
pins should be short to avoid stray capaci-
tance. If the SYNC
IN
pin is not being used it is advisable to
place a guard ring, (connected to input ground) around this
pin to avoid any noise pick up.
The output should be taken from the device using ground
and power planes, this will ensure minimum losses.
A good quality low ESR capacitor placed as close as
practicable across the input will reduce reflected ripple and
ensure a smooth start up.
A good quality low ESR capacitor placed as close as
practicable across the rectifier output terminal and output
ground will give the best ripple and noise performance.
THERMAL MANAGEMENT
Due to the high power density of this device it is advisable
to provide ground planes on the input and output.
FIGURE 3. Connecting Multiple DCV01s in Parallel.
DCV
01
+V
OUT
V
SUPPLY
+V
OUT
V
OUT
V
OUT
0V
V
S
0V
COM
DCV
01
0V
0V
V
OUT
V
SUPPLY
V
S
0V
DCV
01
V
OUT
2 x Power Out
SYNC
IN
SYNC
IN
V
S
0V
COM
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package
Type
Package
Drawing
Pins Package
Qty
Eco Plan
(2)
Lead/Ball Finish
MSL Peak Temp
(3)
DCV010505DP
ACTIVE
PDIP
NVA
7
25
TBD
CU SNPB
Level-NA-NA-NA
DCV010505DP-U
ACTIVE
SOP
DUA
7
25
TBD
CU SNPB
Level-3-240C-168 HR
DCV010505DP-U/700
ACTIVE
SOP
DUA
7
700
TBD
CU SNPB
Level-3-240C-168 HR
DCV010505P
ACTIVE
PDIP
NVA
7
25
TBD
CU SNPB
Level-NA-NA-NA
DCV010505P-U
ACTIVE
SOP
DUA
7
25
TBD
CU SNPB
Level-3-240C-168 HR
DCV010505P-U/700
ACTIVE
SOP
DUA
7
700
TBD
CU SNPB
Level-3-240C-168 HR
DCV010512DP
ACTIVE
PDIP
NVA
7
25
TBD
CU SNPB
Level-NA-NA-NA
DCV010512DP-U
ACTIVE
SOP
DUA
7
25
TBD
CU SNPB
Level-3-240C-168 HR
DCV010512DP-U/700
ACTIVE
SOP
DUA
7
700
TBD
CU SNPB
Level-3-240C-168 HR
DCV010512P
ACTIVE
PDIP
NVA
7
25
TBD
CU SNPB
Level-NA-NA-NA
DCV010512P-U
ACTIVE
SOP
DUA
7
25
TBD
CU SNPB
Level-3-240C-168 HR
DCV010512P-U/700
ACTIVE
SOP
DUA
7
700
TBD
CU SNPB
Level-3-240C-168 HR
DCV010515DP
ACTIVE
PDIP
NVA
7
25
TBD
CU SNPB
Level-NA-NA-NA
DCV010515DP-U
ACTIVE
SOP
DUA
7
25
TBD
CU SNPB
Level-3-240C-168 HR
DCV010515DP-U/700
ACTIVE
SOP
DUA
7
700
TBD
CU SNPB
Level-3-240C-168 HR
DCV010515P
ACTIVE
PDIP
NVA
7
25
TBD
CU SNPB
Level-NA-NA-NA
DCV010515P-U
ACTIVE
SOP
DUA
7
25
TBD
CU SNPB
Level-3-240C-168 HR
DCV010515P-U/700
ACTIVE
SOP
DUA
7
700
TBD
CU SNPB
Level-3-240C-168 HR
DCV011512DP
ACTIVE
PDIP
NVA
7
25
TBD
CU NIPDAU
Level-NA-NA-NA
DCV011512DP-U
ACTIVE
SOP
DUA
7
25
TBD
CU NIPDAU
Level-3-240C-168 HR
DCV011512DP-U/700
ACTIVE
SOP
DUA
7
700
TBD
CU NIPDAU
Level-3-240C-168 HR
DCV011515DP
ACTIVE
PDIP
NVA
7
25
TBD
CU SNPB
Level-NA-NA-NA
DCV011515DP-U
ACTIVE
SOP
DUA
7
25
TBD
CU SNPB
Level-3-240C-168 HR
DCV011515DP-U/700
ACTIVE
SOP
DUA
7
700
TBD
CU SNPB
Level-3-240C-168 HR
DCV012405P
ACTIVE
PDIP
NVA
7
25
TBD
CU SNPB
Level-NA-NA-NA
DCV012405P-U
ACTIVE
SOP
DUA
7
25
TBD
CU SNPB
Level-3-240C-168 HR
DCV012405P-U/700
ACTIVE
SOP
DUA
7
700
TBD
CU SNPB
Level-3-240C-168 HR
DCV012415DP
ACTIVE
PDIP
NVA
7
25
TBD
CU SNPB
Level-NA-NA-NA
DCV012415DP-U
ACTIVE
SOP
DUA
7
25
TBD
CU SNPB
Level-3-235C-168 HR
DCV012415DP-U/700
ACTIVE
SOP
DUA
7
700
TBD
CU SNPB
Level-3-235C-168 HR
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco
Plan
-
The
planned
eco-friendly
classification:
Pb-Free
(RoHS)
or
Green
(RoHS
&
no
Sb/Br)
-
please
check
http://www.ti.com/productcontent
for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
PACKAGE OPTION ADDENDUM
www.ti.com
25-Aug-2005
Addendum-Page 1
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
PACKAGE OPTION ADDENDUM
www.ti.com
25-Aug-2005
Addendum-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI's terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright
2005, Texas Instruments Incorporated
PDF 
ZIP