cPCI200-DC REV A 7/2003

180/225 Watt, 3U x 4HP CompactPCI

cPCI200DC

Corporate: www.cdtechno.com

Corporate: www.cdtechno.com
Product: www.cdpoweronline.com

3U X 4HP

36-72 VDC Input Range

180/225 Watt Continuous Output
Power

Complies with PICMG 2.11 R1.0 with
47 Pin I/O Connector

Hot-Swap Capable

Outputs Individually Protected
Against Overloads; Automatic
Recovery

PCI VoltageArchitecture
(5V, 3.3V,+12V,-12V)

IPMI Capability (Available on Part
Numbers cPCI200D-3 and 4)

The cPCI200DC is a family of high-
reliability, 200 watt power supplies for
3U Compact PCITM systems. Developed
to support hot-swap, redundant
operation, the cPCI200DC Series is
designed for compliance with PICMGTM
2.11 R1.0 Power Interface Specification
with 47-pin I/O connector. Available with
IPMI functionality (part numbers
cPCI200D-3 and cPCI200D-4) , this unit
was developed with high-availability

OUTPUT

SPECIFICATIONS, ALL MODELS

INPUT

PARAMETER

SYMBOL

CONDITIONS

MIN

TYP

MAX

UNITS

Input Operating Voltage

Vin

VDC

Input Voltage Withstand

VDC

Inrush Current

36VDC input

< 20

72VDC input

< 40

Efficiency

48VDC input, full load

(HA) telecommunications applications in
mind. Current sharing and internal ORing
diodes are included to support these and
other applications requiring reliable, hot-
swap performance and N+1 redundant
configuration. The 4HP package and
complement of agency approvals provide
for an advanced, high-density, high-
efficiency power solution for your
CompactPCITM system requirements.

OUT

RATED OUTPUT CURRENTOUTPUT

OUTPUT NUMBER

RATED OUTPUT VOLTAGE

Min

B**

REGULATION

+5.0VDC

18.0 A

27.0 A

+4 / -2%

+3.3VDC

27.0 A

+4 / -2%

+12.0VDC

4.0 A

+/-10%

-12.0VDC

4.0 A

+/-10%

PARAMETER

SYMBOL

CONDITIONS

MIN

TYP

MAX

UNITS

Temperature Coefficient

0.02

%/癈

PARD

20MHz bandwidth

50 mV

P-P

all outputs

or 1.5% P-P

whichever is greater

Output Power

50癈 max temp., 300lfm airflow

180/225

Minimum Load

V1 (config A, 180W)

500

V2 (config B, 225W)

500

NOTES:

Outputs share common return.
*

Total output power not to exceed 180W.

** Total output power not to exceed 225W.
1

Maximum combined power not to exceed 90 Watts.

cPCI200-DC REV A 7/2003

Product: www.cdpoweronline.com

Transient Response

For a step load change of 50%-100%-50%, the peak output
excursion will not exceed 10% of nominal voltage, and will
recover to within 1% of nominal voltage within 500 microseconds.

Current Share

Active current sharing on Outputs V1and V2. Accuracy better than
10% of maximum rated load. Primary referenced.

Remote Sense

Outputs V1and V2 are capable of compensating >50mV of line
drop. Unit automatically reverts to local sensing in the event that
the sense leads are opened for any reason. Unit is protected against
reversed or shorted sense leads.

Output Power

180W (Output configuration A) / 225W (Output configuration
B) continuous maximum, with 300lfm airflow at a maximum
ambient of 50癈. Derate to 90W/110W at 70癈.

Overload Protection

Outputs are individually protected against overloads and
indefinite short circuit with automatic recovery upon removal of
the fault condition.

Over Voltage Protection

Outputs V1 and V2 have Over Voltage Protection at 125% typical
(135% max.) of nominal.

Over Temperature Protection

Outputs are protected against over temperature. Outputs will
automatically restore upon recovery to acceptable temperatures.

Output Fault Isolation

Output isolation diodes are present in all outputs to isolate faults
within a failed power supply.

Remote Inhibit (INH#)

Secondary referenced, active low, TTL compatible signal inhibits
all outputs upon activation.

IPMI Option
Available on Models cPCI200D-3 and cPCI200D-4

An I

C board is available as a factory-installed option to provide

SPECIFICATIONS, ALL MODELS

an IPMI interface to the SM bus. Status functions include output
voltage and current levels as well as the DEG warning. Output
inhibit control can be toggled under software command. For a
complete specification of the firmware solution refer to
Application Note ACAN-02 on our website.

Power Fail Warning (FAL#)

Open collector signal indicates output failure. Active low.

Enable (EN#)

Short pin on connector will enable power supply output when
the mating pin is grounded. Supply will not power up until this
pin is engaged to its mate in the backplane. Unit output will be
inhibited as pin is disengaged from the mating connector.

Temperature Warning (DEG#)

Open collector indicates internal temperatures are approaching
the thermal shutdown limit (+/-10癈, typ). Active low.

Fault Indicator LED

A red LED will be ON if output voltages are not within
specification.

Power Present LED

A green LED will be ON when input voltage is present and above
the minimum requirement.

Cooling

300lfm of airflow required to maintain full output power at 0-
50癈 ambient.

Temperature

Full output power achievable over the range of 0-50癈. Storage
temperature limits are �20 to +85癈.

Altitude

Operating: -200 to +10,000 feet with ambient temperature
derating above 5,000 feet in accordance with the adiabatic lapse
rate (approximately 2C per 1000 feet).

Inhibit Indicator LED (Yellow)

A yellow LED will be ON when the outputs are inhibited.

Complies with IPMI V1.5 Rev 1.1 and IPMB V1.0

Complies to PICMG 2.9 (CompactPCI Systems Manage-
ment Specification)
8 analog inputs configured for monitoring voltages and currents
on power supply outputs V1 - V4
Monitors the state of the thermal sensor

Output inhibit can be controlled by IPMI commands

Self Test with LED indicator (can be read and overridden
by IPMI commands)
6 programmable thresholds on each analog sensor

Each threshold on each sensor can be enabled to generate
event messages if that threshold is crossed

Thermal sensor can be enabled to generate event messages

Responds to all mandatory IPMI commands and numerous
optional commands as indicated in the functional specifi-
cation
Firmware can be upgraded via the IPMB bus

Includes Device SDR's (Sensor Data Records) - These
specify the type of sensor for each input (voltage, current,
temperature, etc.) as well as the conversion formulas from
raw ADC data to voltages, currents, etc.
Includes FRU data such as model number, serial number
and firmware creation date

IPMI/IPMB POWER SUPPLY SATELLITE CONTROLLER FEATURES

AVAILABLE ON PART NUMBERS cPCI200D-3 AND cPCI200D-4

cPCI200-DC REV A 7/2003

Product: www.cdpoweronline.com

NOTES: All measurements are in inches.

Weight: 1.4 lbs. (636g) net

MECHANICAL

PIN ASSIGNMENT: Pin assignment consistent with PICMGTM 2.11R1.0 specification. The table below details the PICMGTM assignment.

NOTES: (1) Pin numbers correspond to the female backplane connector.

(2) L = Long Length Pin (First Make, Last Break); M = Medium

Length Pins; S = Short Length Pins (Last Make, First Break)

Pin #

Staging

Signal Name Description

1-4

V1 Output

5-12

RTN

V1 and V2 Return

13-18

V2 Output

RTN

V3 Return

V3 Output

V4 Output

RTN

Signal Return

RESERVED

Reserved

RTN

V4 Return

GA0

Geographic Address Bit 0

RESERVED

Reserved

EN#

Enable

GA1

Geographic Address Bit 1

V1ADJ

V1 Adjust

V1 SENSE

V1 Remote Sense

GA2

Geographic Address Bit 2

V2ADJ

V2 Adjust

V2 SENSE

V2 Remote Sense

S RTN

Sense Return

V1 SHARE

V1 Current Share

V3 SENSE

V3 Remote Sense

IPMB SCL

IPMB Serial Clock Line

DEG#

Degrade Signal

INH#

Inhibit

IPMB SDA

IPMB Serial Data Line

V2 SHARE

V2 Current Share

FAL#

Fail Signal

IPMB PWR

IPMB Power Input

V3 SHARE

V3 Current Share

CGND

Chassis Grnd (Safety Grnd)

ACN/+DC IN

AC Input Neutral/+DC Input

ACL/-DC IN

AC Input Line/-DC Input

MECHANICAL

Shock: MIL-STD-810d, Method 516.3, Procedure 1.
Vibration: MIL-STD-810d, Method 514.3, Procedure 1.
Dimensions: 3U x 4HP x 160mm (see Mechanical above)

EMC & SAFETY

EMI: NEBS Compliant to GR1089 conducted emissions limit

ETSI Compliant to ETS 300-386 conducted emissions
limit

Safety Agency Ratings

180 Watt

225 Watt

Input Voltage:

36-72 V

Input Current:

Input Power:

260W

320W

Agency Approvals Pending

UL1950/CSA950, EN60950, CE Mark.
(Low Voltage Directive)

cPCI200-DC REV A 7/2003

Product: www.cdpoweronline.com

Any data, prices, descriptions or specifications presented herein are subject to revision by C&D Technologies, Inc. without notice. While such information is believed to
be accurate as indicated herein, C&D Technologies, Inc. makes no warranty and hereby disclaims all warranties, express or implied, with regard to the accuracy or
completeness of such information. Further, because the product(s) featured herein may be used under conditions beyond its control, C&D Technologies, Inc. hereby
disclaims all warranties, either express or implied, concerning the fitness or suitability of such product(s) for any particular use or in any specific application or arising
from any course of dealing or usage of trade. The user is solely responsible for determining the suitability of the product(s) featured herein for user's intended purpose
and in user's specific application. C&D Technologies, Inc. does not warrant or recommend that any of its products be used in any life support or aviation or aerospace
applications.

Power Electronics Division, Americas

3400 E Britannia Drive, Tucson, Arizona 85706

Tel: 800.547.2537 Fax: 520.295.4197

C&D Technologies, EMEA/Asia Pacific

Milton Keynes MK14 5BU UK

Tel: +44 (0)1908 615232 Fax: +44 (0)1908 617545

ORDERING INFORMATION

PART NUMBER

POWER

+5V

+3.3V

+12V

-12V

IPMI

cPCI200D-4

225 W

27A

YES

cPCI200D-3

180 W

18A

27A

YES

cPCI200D-2

225 W

27A

cPCI200D-1

180 W

18A

27A

协谢械泻褌褉芯薪薪褘泄 泻芯屑锌芯薪械薪褌: CPCI200D-1

协谢械泻褌褉芯薪薪褘泄泻芯屑锌芯薪械薪褌: CPCI200D-1