Specifications are subject to change without notice (07.09.99)
1
Dupline
Field- and Installationbus
4-digit 7-segment LED-display with sign
Freely scaleable
2 relay limit outputs (HI, LO)
2 NPN transistor limit outputs (HIHI, LOLO)
LED-indication for all limit outputs
Automatic or manual reset of limit outputs
Protocol selectable (3 1/2-digit BCD, 4-digit BCD,
8 bit binary)
Multiplex or normal mode
Internal or external selection of multiplex address
AC power supply
Product Description
Freely scaleable Dupline 4
digit LED-display with sign,
for panel mounting. Readout
of analog signals, counter
values or time. 4 limit outputs
with LED-indication. Protocol
selectable (3 1/2 digit BCD,
4-digit BCD, 8 bit binary)
Type Selection
Supply
Ordering no.
8/16 channels
4-digit LED
24 VAC
D 6369 6475 024
115/230 VAC
D 6369 6475 230
No code module required
Input/Output Specifications
Inputs
Limit output reset
1 contact or NPN transistor
Multiplex address selection
4 contacts or NPN transistors
Open loop voltage
5 VDC
Short circuit current
50 A
Contact resistance
10
Cable length
2 m
Dielectric voltage
Inputs - Dupline
500 VAC (rms)
Inputs - Relay outputs
4 kVAC (rms)
Inputs - Transistor outputs
4 kVAC (rms)
HI, LO - limit outputs
2 SPST relays
Isolated in groups of
2 x 1
Contact ratings (AgCd0)
(micro gap)
Resistive load
AC1
5 A/250 VAC (1100VA)
DC1
0.25 A/250 VDC (62 W)
or
5 A/25 VDC (125 W)
Inductive loads
AC15
2.5 A/230 VAC
DC13
5 A/24 VDC
Mechanical life
30 x 10
6
operations
Electrical life (max. load)AC1
2.5 x 10
5
operations
Operating frequency
7200 operations/h
Dielectric voltage
Outputs - Dupline
4kVAC (rms)
Outputs - transistor outputs
4kVAC (rms)
Type: Dupline
Type no.
Supply
Ordering Key
Display Receiver with Limit Outputs
Type D 6369 6475
D 6369 6475 024
Display
Display format
7-segment
Display range
-9999 to +9999 (4 digits)
Display type
LED
Height of digits
14.2 mm
Display colour
Red
Change of sign (automatic)
Yes
Decimal point
Configurable by keys
Scaling feature
Yes
Multiplex feature
Yes
Display test
Yes
Transmission protocol
3 1/2, 4-digit BCD,
8 bit binary
Limit values
4 (HIHI, HI, LO, LOLO)
Settings
Channel address
Keys and display
Multiplex address (internal)
Keys and display
Scaling
Keys and display
Decimal point position
Keys and display
Limit values
Keys and display
Normal/multiplex mode
Keys and display
Enable/disable limit outputs
Keys and display
Transmission protocol
2 DIP switches
Internal/external selection of
multiplex address
1 DIP switch
Automatic/manual reset of
limit outputs
1 DIP switch
2
Specifications are subject to change without notice (07.09.99)
Power supply
Overvoltage cat. III (IEC 60664)
Rated oprational
voltage
230
115 and 230 VAC 15%
024
24 VAC 15%
Frequency
45 to 65 Hz
Dropout tolerance
4.5 ms
Rated operational power
Typ. 8 VA
Rated operational withstand
voltage
230
4 kV
024
800 V
Dielectric voltage
Supply - Dupline
4 kVAC (rms)
Supply - Inputs
4 kVAC (rms)
Supply - Relay outputs
4 kVAC (rms)
Supply - Transistor outputs
4 kVAC (rms)
D 6369 6475
General Specifications
Power ON delay
3s
Indication for
HIHI limit output
LED, red
HI limit output
LED, yellow
LO limit output
LED, yelow
LOLO limit output
LED, red
Environment
Degree of protection
IP 20
Pollution degree
3 (IEC 60664)
Operating temperature
0 to +60C (+32 to +140F)
Storage temperature
-25 to +85C (-13 to +185F)
Humidity (non-condensing)
0 to 80%
Mechanical resistance
Shock
15 g (11 ms)
Vibration
2 g (6-55 Hz)
Material
Glass-reinforced Noryl
Weight
460 g
Approvals
UL, CSA
Supply Specifications
Mode of Operation
4-digit 7-segment LED dis-
play used to monitor analog
signals, counter values or
time of the day.
The display value is freely
scaleable within the range
-9999 to +9999 with select-
able position of the decimal
point. Values from 3 1/2-digit
BCD, 4-digit BCD and 8-bit
binary transmitters can be
displayed, since the trans-
mission protocol is select-
able.
4 limit outputs are available:
HI, LO
-relay outputs
HIHI, LOLO
-NPN transis-
tor outputs
Each output can be allocated
freely to any scaled display
value. The limit outputs turn
on whenever the value con-
trolling the outputs is equal
or above the limit value
setting for HI and HIHI (equal
or below for LO and LOLO).
It is selectable whether the
limit outputs shall be reset
automatically (by the value
controlling the limit outputs
returning to normal) or
manually by activation of the
"Limit Reset" - input. The limit
outputs may also be disabled
if this feature is not required.
4 LEDs at the front also
indicate the signal level com-
pared to the 4 limit settings,
blinking upon limit alarm,
steady state after a manual
reset. The display can be
used in normal mode as well
as in multiplex mode (3 1/2-
digit BCD protocol only).
When used in multiplex
mode, the multiplex address
for the display may be
selected by a selector switch
(e.g. on the cabinet door) that
connects to the "Multiplex
Address" inputs. Each of the
display values from the 16
multiplex addresses can be
scaled individually. The limit
value setting however will
always refer to the multiplex
address defined during the
configuration.
With the 4 keys at the front
the display shifts to program
mode, in which scaling,
decimal point position, limit
value settings, channel ad-
dress, multiplex address etc.
is configured.
For further information please
refer to the "User Manual"
delivered with the unit.
Display Specifications
HIHI, LOLO limit outputs
2 NPN transistors
Watchdog-output
1 NPN transistor
Isolated in groups of
1 x 3
Output voltage range V
BB
6-60 VDC
Reverse-polarity protection
None
Current per output
250 mA
Total load capability
100%
Short-circuit protection
None
Built-in protective diodes
None
Off-state leakage current
500 A
Output voltage drop
2.5 V
Dielectric voltage
Outputs-Dupline
4 kVAC (rms)
Response time
Multiplex input
1 pulse train
Reset inputs
1 pulse train
Limit outputs
1 pulse train
Watchdog output
1 pulse train
Specifications are subject to change without notice (07.09.99)
3
D 6369 6475
Settings
Multiplex Address Selection Inputs
Multiplex
Multiplex address
address
input terminals
0
0
0
0
0
1
0
0
0
1
2
0
0
1
0
3
0
0
1
1
4
0
1
0
0
5
0
1
0
1
6
0
1
1
0
7
0
1
1
1
8
1
0
0
0
9
1
0
0
1
a
1
0
1
0
b
1
0
1
1
c
1
1
0
0
d
1
1
0
1
e
1
1
1
0
f
1
1
1
1
MSB
LSB
Functional Description
Watch Dog
HiHi Output
Common
LoLo Output
Lo Output
Hi Output
Dupline Signal
Dupline
Multiplex Input for readout
Reset Input
Power Supply
Dimensions (mm)
Wiring Diagrams
Power supply
Programming keys
DIP-switch for
function selection
PDF 
ZIP