Du line
Fieldbus
Installationbus
Specifications are subject to change without notice (23.10.2006)
1
Dupline
is a registered trademark. A product of the CARLO GAVAZZI Group
Product De scrip tion
Ordering Key
Type: Dupline
Mini-E housing
Function
No. of channels
Input type
Transmitter for Digital Signals
Type G 5010 2206
Dual channel transmitter
Contact inputs
Input pulse prolongation
Codeable LED output e.g. for feedback purposes
Supplied by Dupline
, no external supply required
Mini-E housing
Direct wall or DIN-rail mounting
Channel coding by GAP 1605
Supply Spec i fi ca tions
Power supply
Supplied by Dupline
Current consumption
with LED OFF
Typ. 450 A
with LED ON
Typ. 1.2 mA
General Spec i fi ca tions
Environment
Degree of protection
IP 20
Pollution degree
3 (IEC 60664)
Operating temperature
-20 to +50C (-4 to +122F)
Storage temperature
-50 to +85C (-58 to +185F)
Humidity (non-condensing)
20 to 80%
Mechanical re sist ance
Shock
15 G (11 ms)
Vibration
2 G (6 to 55 Hz)
Dimensions
49 x 22.5 x 56 mm (L x W x H)
Material
PC/ABS blend
Input Spec i fi ca tions
Inputs
2 contacts
Open loop voltage
2.5 VDC
Short-circuit current
17 A
Operating time for signal "1"
< 1 pulse train + 10 ms
Operating time for signal "0" < 1 pulse train + 500 ms
Contact resistance
< 1 k
Cable length
< 3 m
Dielectric voltage
Input - Dupline
None
G 5010 2206
Dupline
-powered dual chan-
nel
transmitter in Mini-E
housing with contact inputs.
Especially well suited in places
where no power supply is
available. On each input,
there is built-in pulse prolon-
gation which ensures that
even short input pulses are
transmitted. Upon activation
of an input a short charge
current pulse ensures that
the contacts are kept clean.
On the front of the module,
there is a red LED which can
be coded for any Dupline
channel address for indica-
tion of channel ON status.
Supply
Ordering No.
2 channels
Contact
Supplied by Dupline
G 5010 2206
Type Selection
Du line
Fieldbus
Installationbus
2
Specifications are subject to change without notice (23.10.2006)
Dupline
is a registered trademark. A product of the CARLO GAVAZZI Group
I1
I2
G 5010 2206
Mode of Operation
Wiring Diagram
Programming cable
to GAP 1605
GAP-TPH-CAB
DIN-rail FMD
411
Accessories
Dupline
-powered dual chan-
nel transmitter with contact
inputs. There is built-in pulse
prolongation on each input
to ensure that even short
input pulses are transmitted.
The inputs and the LED out-
put can be coded individual-
ly by means of the code pro-
grammer GAP 1605. For
details, please refer to the
respective data sheet. Please
note that a special cable
(GAP-TPH-CAB) is required to
connect the GAP 1605 to the
programming plug behind the
front plate of G 5010 2206.
The channel address for the
inputs is selected under I/O-
1 and I/O-2 on the GAP
1605. If an address is
assigned to I/O-3 or I/O-4,
this address will be activat-
ed continuously.
On the front of the module
there is a red LED which can
be coded to indicate the sta-
tus of 2 Dupline
channels.
The LED output can be an
OR-function of the 2 inputs.
This is achieved by assign-
ing the same addresses to
I/O-5 and I/O-6, as have
been assigned to I/O-1 and
I/O-2.
D+
D -
Dimensions (mm)
Mini-E-housing
55.4
22.5
56
47.4
15
49
4 x 3.4
PDF 
ZIP