Du line

Fieldbus

Installationbus

Specifications are subject to change without notice (06.09.2006)

Dupline

is a registered trademark. A product of the CARLO GAVAZZI Group

Type: Dupline

OPUS housing
Input type
4 channels
4 inputs
Colour/input type
Supply

Ordering Key

Product Description

G82864406703 is a 4-channel
transceiver with 4 contact
inputs and 4 LEDs for indica-
tion of received signal from
the G34860058230 base. It
can be used alone or integrat-
ed in the OPUS-66 series
from the Danish supplier LK.

The light switch is part of the
Dupline

"Smart House"

building automation concept
and can be used to control
lights, roller blinds/Venetian
blinds and other functions
supported by the master gen-
erator.

· Dupline transmitter for building automation applications
· 4 individually programmable push-button inputs
· Channel programming using GAP 1605
· Wall mounting
· Range up to 100 m in open air
· 3 V battery supply (CR2032)
· Battery life: up to 5 years at normal use

Type Selection

Input Specifications

Wireless push-button
Transmission frequency

868 MHz

Supply Specifications

Power supply

Battery: CR2023

OPUS wireless light switch
Type G8286 4406 703

General Specifications

Channel coding

Via GAP 1605 and special
cable: GAP-TPH-CAB

Out 1-4

Push-button 1-4

Housing

(LK OPUS)

Environment

Protection degree

IP 20

Pollution degree

3 (IEC 60664)

Operating temperature

0-50°C/32-122°F

Storage temperature

-20-70°C/-4-158°F

Humidity
(non-condensing)

20 - 80%

Weight

50 g without battery

Dimensions

66 x 66 x 11 mm
(including frame)

Supply

Colour

Ordering no.

Dupline

White

G 8286 4406 703

Light grey

G 8286 4408 703

G 8286 4406 703

Mode of Operation

The G8286 440x 703 light
switch is designed for base
unit G3486 0058 230 and will
only function with this unit.
The wireless G8286 440x 703
light switches are pro-
grammed as standard light
switches G8x10 44xx using a
GAP1605 (see data sheet for
this unit).
The communication between
G8286 440x 703 light switches
and the G3486 0058 230
base is established in the fol-
lowing way:
- Push the "Mode" button on
the G3486 0058 230 base
until the red LED indicates
association.
- Push the push-button on the

G8286 440x 703 light switch
module that you want to
associate with the G3486
0058 230 base.
Once the association is com-
plete, all 4 LEDs will light up
briefly (approx. 1 second).
If the association fails, e.g.
because the range is exceed-
ed, all LEDs in the light switch
module will light up simulta-
neously for approx. 500 ms.
This also occurs if, under nor-
mal circumstances, it is not
possible to establish connec-
tion between the G3486 0058
230 base and the G8286 440x
703 light switch modules.
It is possible to disable the
communication between the

G3486 0058 230 base and all
the modules with which it is
associated.
- Push the "Mode" button on
the G3486 0058 230 base
until the red "Disable" LED is
lit.
This means that there is no
connection between the
G3486 0058 230 base and its
associations.
To reestablish the connection,
push "Mode" until neither
"Associate" or "Deactivate"
are lit.
Under normal circumstances,
the "Supply" and "Dupline"
LEDs will be lit continuously,
whereas the LED for "Com-
munication" only blinks briefly

when you push an associated
G8286 440x 703 light switch.
The LEDs always follow their
allocated push-button and
cannot be programmed indi-
vidually or removed.
The LED indication provides
confirmation that the commu-
nication is successful.

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: G82864408703

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: G82864408703