ChipFind - документация

Электронный компонент: S1422156115

Скачать:  PDF   ZIP
Specifications are subject to change without notice (25.06.99)
1
Photoelectrics
Amplifier
Type S1422
Product Description
Ordering Key
Type
Special function
Output type
Power supply
Amplifier relay for long range
photoelectric switch types
MOF, MIF, MKF, MHF, MCF,
MDF, MMF, MNF and MFFD.
8 different light modulation
frequencies (F1 or F8) can be
selected to avoid optical
crosstalk between neighbour-
ing systems. Misalignment
and dirt accumulation alarm
output. Make and break
switching function DIP-switch
selectable. Short-circuit pro-
tected supply to photoelectric
switches.
Type Selection
Plug type
Function
Ordering no.
Ordering no.
Ordering no.
Ordering no.
Supply: 24 VDC
Supply: 24 VAC
Supply: 115 VAC
Supply: 230 VAC
Circular
Adjustable sen-
S 1422 156 724
S 1422 156 024
S 1422 156 115
S 1422 156 230
11 pins
sitivity, dirt alarm,
alignment indication
8 modulation frequen-
cies selectable
Note: Photoelectric switches type M.F to be ordered separately.
Specifications
Rated operational volt.
AC types (U
B
)
Pins 2 & 10
230
195 to 265 VAC, 45 to 65 Hz
115
98 to 132 VAC, 45 to 65 Hz
024
20.4 to 27.6 VAC, 45 to 65 Hz
Voltage interruption
40 ms
Dielectric voltage
2.0 kVAC (rms)
Rated impulse withstand volt. 4 kV (1.2/5 0
s)
Rated operational volt.
DC types (U
B
)
Pins 2 positive &
10 negative
724
20.4 to 27.6 VDC
Dielectric voltage
None
Rated impulse withstand volt. 800 V (1.2/50
s)
Rated operational power
AC supply
2.5 VA
DC supply
1.0 W
Supply to photoelectric switch
Emitter
Pins 5 & 7
Supply voltage (open loop)
8 V square wave
Current
100 mA short-circuit
protected
Light modulation frequency
2.2 KHz to 3.5 KHz
DIP-switch selectable
Output resistance
47
Receiver
Pins 6 & 8
Supply voltage (open loop)
8 VDC
Short-circuit current
18 mA
Input resistance
470
Approvals
UL, CSA
CE-marking
Yes
Amplifier relay for photoelectric switches
8 selectable light modulation frequencies
Adjustable sensitivity
Dirt accumulation alarm and alignment control
Modulated and synchronized light
Make and break switching funct. DIP-switch selectable
Rated operational voltage: 24 VDC or VAC, 115 VAC,
230 VAC
Output 10 A/250 V SPDT relay and 100 mA NPN
Plug-in module
LED indications: Power supply, output, level
S142 2 156 724
2
Specifications are subject to change without notice (25.06.99)
S1422
Specifications (cont.)
Output Specifications
Switching function
Contact output current (1 & 3)
Continuous AC (I
e
)
10 A/250 VAC ohmic load
(2500 VA)
Continuous DC (I
e
)
1 A/250 VDC ohmic load
(250 W)
Contact life mechanical
30 x 10
6
operations
Contact life electrical
2.5 x 10
5
operations
NPN Output (Pin 9)
Continuous (I
e
)
100 mA/40 VDC
Short-time (I)
100 mA/40 VDC
Alarm function (Pin 11)
NPN Output
Continuous (I
e
)
100 mA/40 VDC
Short-time
100 mA/40 VDC
Rated insulation volt. (U
i
)
250 VAC (rms)
Dielectric voltage
2.0 kVAC (rms)
(contact/electronics)
Rated impulse withstand volt. 4 kV (1.2/50
s) (contact/
electronics) (IEC 60664)
Sensitivity
Adjustable with 270 turn
knob
Operating frequency (f)
Light/dark ratio 1:1
Contact output
30 Hz
NPN output
45 Hz
Response time
OFF-ON (t
ON
): contact output 16 ms
NPN output
11 ms
ON-OFF (t
OFF
): contact output 16 ms
NPN output
11 ms
Power ON delay (t
V
)
< 300 ms
Output function
Make and break switching
DIP-switch selectable
Indication
Supply ON
LED, green
Output ON
LED, red
Alignment/dirt accumulation
LED, yellow (Steadily on if
(sensitivity level)
sensitivity adjusted properly)
Environment
Overvoltage category
III (IEC 60664)
Degree of protection
IP 20 (IEC 60529, 60947-1)
Pollution degree
3 (IEC 60664/60664A, 60947-1)
Temperature
Operating
-20 to +50C (-4 to +122F)
Storage -50 to
+85C (-58 to +185F)
Weight
AC supply
200 g
DC supply
125 g
Operation Diagram
Power supply
Object present, light beam interrupted
Output ON:Break switching pin 1, 3*
Make switching pin 1, 3*
*) Switching function selected by DIP-switch, inverted function on pin 1, 4.
Tv
Tv
Truth Table
Object present
Yes
No
No
Yes
No
No
Dirt on lenses,
misaligned or
--
No
Yes
1)
--
No
Yes
1)
sensitivity too low
Output LED red
OFF
ON
ON
ON
OFF
OFF
Level LED yellow OFF
OFF
Load
Pins 1&3
N-act.
Active
Active
Active.
N-act.
N-act.
Output NPN
Pi. 9&7
High
Low
Low
Low
High
High
Alarm Output
2)
NPN
Pins 11&7
High
High
Low
High
High
Low
1)
Under normal operating conditions, the yellow level indica-
tionLED has to be on steadily (bright) and alarm output
has to be high.
2)
The alarm output will turn on shortly each time an object
enters or exits the sensing zone, even if the photoelectric
switch is correctly installed and adjusted. To avoid false
signals, the alarm functions should be delayed with an
external ON delay timer (i.e. Carlo Gavazzi timer S111
series).
Make switching
Break switching
ON
steadily
OFF or
weakly OFF
2)
ON
steadily
OFF or
weakly OFF
2)
Specifications are subject to change without notice (25.06.99)
3
S1422
Dimensions
Supply green
Output red
Sensitivity
level
Switching
function
F5
F6
F7
F8
F1
F2
F3
F4
Make switching
Break switching
DIP-switches
Light modulation
Frequencies
Sensitivity level yellow
DIP-switches
Light modulation
frequencies
Switching function
pin 1&3
Wiring Diagrams
Through-beam
Photoelectric Switch types
MIF, MKF, MCF, MDF, MMF, MNF, MHF, MOF
Diffuse-reflective
Photoelectric Switch types
MFFD
Accessories
- 11 pole circular socket
S111, S111A, S411, ZPD11
- Socket cover for S111
BB1
- Socket cover for S411
BB4
- Holding down spring
HF
- Mounting rack
SM13
- Front panel mounting bezel
FRS2
- Potentiometer knob lock
PL1
Delivery Contents
Amplifier
Packaging: styropor box
Output NPN
Emitter
(grey cable)
Receiver
(black cable)
(+)
(-)
~
~
Alarm
output
NPN
Power supply
Output NPN
Red
Y
ellow
(+)
(-)
~
~
Alarm
output
NPN
Power supply
Alarm Diagram
Signal power
Relay
Level
t
Alarm
Level
Relay