Specifications are subject to change without notice (19.06.2006)
1
Ultrasonic
Diffuse, Analogue Output
Type UC 80 CND 60 A . M1 TR
Product Description
Ultrasonic sensor
Housing style
Housing size
Housing material
Housing length
Detection principle
Sensing distance
Output type
Output configuration
Connection
Remote teach
Type Selection
Housing Connection
Rated
operating
Outputs
Ordering
no.
dimensions
dist. (S
n
)
80 x 80 x 50 mm
Plug M12, 5 pin
600-6000 mm
0-10 V
UC 80 CND 60 AK M1 TR
80 x 80 x 50 mm
Plug M12, 5 pin
600-6000 mm
4-20 mA
UC 80 CND 60 AG M1 TR
Ordering Key UC80CND60AKM1TR
A self-contained multi func-
tion diffuse ultrasonic sensor
with a sensing range of 600
to 6000 mm. The analog
output is easily set up in 2
setpoints, pos./neg. slope
and adjusted by teach-in -
makes it ideal for level con-
trol tasks in a wide variety of
vessels. A sturdy one-piece
ABS housing provides the
perfect packaging for the
sofisticated microprocessor
controlled and digitally fil-
tered sensor electronics.
Excellent EMC performance
and precision are typical
features of this sensor
based on true distance
measurement.
Technical Data
Rated operational volt. (Ue)
15 to 30 VDC (ripple included)
Ripple
10%
No-load supply current (Io)
35 mA
Protection
Short-circuit, transients and
reverse polarity
Rated insulation voltage
> 1 kV
Power-on delay
420 ms
Output
UA..CLD..AK..
0-10 VDC
UA..CLD..AG..
4-20 mA
Output slope
Positive or negative
Setup via teach-in
Linearity error
< 0.5%
Repeat accuracy (R)
0.2% 2 mm
Rated operating distance/
Resolution
1.5 mm
Load
4-20 mA
max. 500
0-10 V
min. 2 k
Carrier frequency
80 KHz
Indication
Set points, 2 LEDs yellow
Echo, 1 LED green
Rated operating distance
600 - 6000 mm
Temperature compensation
Yes
Beam angle
8
Ambient temperature
Operating and Storage
-15 to +70C (5 to +158F)
Degree of protection
IP 65
Housing material
ABS
Connection
Plug M12, 5-pin
Cables for plug (M1)
CONM15 series
Weight
300 g
CE-marking
Yes
Square 80 mm ABS housing
Sensing distance: 600 - 6000 mm
Remote Teach by wire
Outputs: Analog 0-10 V or 4-20 mA
Setup of positive or negative slope
Power supply: 15 to 30 VDC
8 beam angle
Protection: Short-circuit, reverse polarity, transients
Protection degree IP 65
M12 plug, 5 pin
2
Specifications are subject to change without notice (19.06.2006)
UC 80 CND 60 A. M1 TR
Analogue Output Adjustment
Echo
P1
P2
Green Yellow Yellow
Teach in of P1 position
Teach in of P2 position
Teach-In for
8 sec
14 sec
Normal function:
The Echo LED is ON when the echo is received (this is the
alignment LED confirming that the target is properly aligned).
The LED P1 is ON, when the target is between the sensor
face and P1. The LED P2 is ON when Target is farther than
P2.
Teach-In for
14 sec
Detection Range
600
6000
+800
-800
mm
mm
Guaranteed detection of a target 100 x 100 mm
Possible detection of a large target
Dimensions
Dimensions in mm.
+
-
1 BN
3 BU
4 WH
Teach-in
5 PK
(GY)
5
3
2
1
4
Wiring Diagram
Specifications are subject to change without notice (19.06.2006)
3
V
10
0
600
6000 mm
UC 80 CND 60 A. M1 TR
Installation Hints
Relief of cable strain
Protection of the sensing face
Switch mounted on mobile carrier
To avoid interference from inductive voltage/
current peaks, separate the prox. switch
power cables from any other power cables,
e.g. motor, contactor or solenoid cables
Incorrect
Correct
The cable should not be pulled
A proximity switch should not serve as
mechanical stop
Any repetitive flexing of the
cable should be avoided
Analogue output adjustment
P1 and P2 define the analogue output slope.
P1 determines the 4 mA position and P2 the 20 mA position.
Positive slope:
P1 < P2
Negative slope:
P2 < P1
Teach-In of P1 position (4 mA output)
Hold Teach-In for 8 seconds until P1 and Echo LED's start
flashing 2 times per second.
The sensor is now in teach mode for P1:
P1 LED will now flash once per second and the Echo LED
returns to normal function (alignment LED).
The Teach-In function is now open for 1 minute to do the
programming of P1.
Place the target at the new position P1.
Activate Teach-in: P1 is now programmed.
Sensor returns to normal function with new value for P1.
Teach-In of P2 position (20 mA output)
Hold Teach-In for 14 seconds until the P2 and Echo LEDs
start flashing 2 times per second. After 8 seconds, the P1
and Echo LEDs will start flashing, but this must be ignored
and after an additional 5 seconds the P2 is reached.
The sensor is now in teach mode for P2:
P2 LED is flashing once per second. The Echo LED returns
to normal function (alignment LED).
Teach-mode is now open for 1 minute to do the program-
ming of P2.
Move the target to the new position P2.
Activate Teach-in: P2 is now programmed.
Sensor returns to normal function with new value for P2.
Teach-in procedure
Output Functions
Voltage Output
Current Output
mA
20
4
600
6000 mm
PDF 
ZIP