Network Software for Energy Management
Type WattSoft3
The following configuration submenus are available:
programming of data protection PASSWORD;
selection of the NUMBER OF INSTRUMENTS
belonging to the network;
selection of the parameters belonging to the
INSTRUMENTS NETWORK;
selection of network WORKING MODE;
selection of ADDITIONAL VARIABLES
programming of the parameters for the ENERGY
COSTS management
parameters of the DATA PRINTING mode.
The instruments network configuration menu
Selection of the following parameters:
instrument number (address);
type of instruments to be managed: SPT, EM2,
EM4, WM12, WM2, WM22, WM23, WM3, WM24,
WM4, etc.
network communication activation: ON / OFF;
type of electrical wiring system
Management of up to 255 instruments
Supervision and control of all the electrical variables
managed by the instruments
Management of single loads with a specific monitor-
ing page
Graphic display of the variables of all instruments
Alarm management of all instruments
Logging of the alarm history
Energy Management
agement of up to 255 instru-
ments like - SPT, EM2, EM4,
WM12, WM2, WM22, WM23,
WM3, WM24, WM4, etc. by
means of a MODBUS (RS485)
communication protocol:
- the SCADA system allows
the management of all the
electrical variables being
measured in order to optimise
the energy consumption and
therefore to reduce the rele-
vant costs.
Product Description
WATTSOFT3 is a Windows
95, 98, 2000, NT, ME and XP
network software for energy
management. This powerful
virtual instrument combined
with the Carlo Gavazzi hard-
ware is the most up-to-date
answer to all the power and
energy parameter control
needs.
WattSoft3 is a software pack-
age that is able to figure out
two basic problems: the man-
Ordering Key
WATTSOFT 3
Model
General Specifications
The set-up menus
1
WS3DS0703 Specifications are subject to change without notice
This flexible software can be config-
ured, by means of various setting
menus, to manage and display all the
measured electrical parameters.
A powerful alarm control is available
The alarm set-points menu:
Available parameters:
Programming of single instrument's user name;
List of instruments available in the network;
Type of variables to be managed;
Type of alarms
SW alarm working mode (it can also be HW
depending on the type of instrument available
in the network)
for each measurement and for all instruments
belonging to the network.
The energy costs can be calculated according to
various references like: tariff, power and energy
rates.
General Specifications (cont.)
Other characteristics
Specifications are subject to change without notice WS3DS0703
2
Data pages
Main page (Total data)
The main page "TOTAL DATA" shows the execu-
tion status of the measurements, indicating the
list of all the variables with the measurement
results; giving the possibility to reset the total
consumed energies, the alarms, the hour counter
and allowing the operator to display various
graphs:load profile, cost, energy, power, current,
voltage, power factor and combination of vari-
ables.
Single data page (Single data)
The "SINGLE DATA" page shows the details of a
group of up to six instruments, indicating: the
number of the displayed monitoring page, the
user names of the instruments "USERS"; the list
of all the variables with the measurements results
and those measurements indicating the presence
of alarm status; the user can reset the total con-
sumed energies, the alarms and the hour
counter.
Total data graph
This monitoring page can be divided into four parts:
- on the upper area it is possible to select the
instrument whose graph and period are to be dis-
played; this page also shows the alarm status of
the system, the user name, the wiring system of
the instrument, the current date and time;
- in the middle, the graph of up to four variables;
- on the right, all the info connected to the graph
(including zoom functions and selection between
automatic or manual axis range);
- at the bottom, a button to enable the graph manual
printing and a button to go back to the TOTAL DATA
page.
WattSoft3
PDF 
ZIP