THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
P R O D U C T D A T A S H E E T
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
CRYSTAL CONTROLLED OSCILLATORS
The Connor-Winfield
EGOV5S3M is a hermetically
sealed 14 Pin DIP 5.0V Oven
Controlled, Voltage Controlled
Crystal Oscillator (OCVCXO)
with a Tri-State HCMOS
output. The EGOV5S3M
features an Oven Ready
Monitor and is designed for
Stratum 3 applications
requiring low jitter and tight
frequency stability.
1
2
EGOV5S3M - 62.208MHz
OCXO
SERIES
CENTER
FREQUENCY
FEATURES
DESCRIPTION
ORDERING INFORMATION
5.0V OPERATION
FREQUENCY ADJUST
TRI-STATE ENABLE / DISABLE
FUNCTION
LOW JITTER <1pS RMS
FREQUENCY STABILITY: 0.25ppm
FREQUENCY TOLERANCE: 4.6ppm
TEMPERATURE RANGE: 0 to 70C
OVEN READY MONITOR
HERMETICALLY SEALED PACKAGE
14 PIN DIP 5.0V HCMOS STRATUM 3 OCVCXO
with OVEN READY MONITOR
Cx061
00
8/28/03
www.conwin.com
EGOV5S3M
CW 0107
EGOV5S3M
62.208M
Notes:
1) Frequency vs. temperature stability, Vc = 2.50V.
2) Inclusive of calibration, operating temperature range, supply voltage change, load change, shock
and vibration, 10 years aging, Vc = 2.50V.
3) After one minute of operation at 25
C, the unit will be within +/-0.5ppm of its final stabilized
frequency. The final stabilized frequency is that which is measured after 30 minutes of continuous
operation at a stable 25
C ambient temperature.
4) Referenced to Fo @ 25
C
, Positive Transfer Characteristic
5) Oscillator output is enabled with no connection on pin 3.
ABSOLU TE MAXI MUM RAT INGS
TABLE 1.0
PARAMETER
UNITS
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Storage Temperature
-40
-
85
C
Supply Voltage
(Vcc)
-0.5
-
7.0
Vdc
Control Voltage
(Vc)
-0.5
-
7.0
Vdc
OPERATING SPECIFICATIO NS
TABLE 2.0
PARAMETER
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Center Frequency
(Fo)
40
-
80
MHz
Frequency Stability
-0.25
-
0.25
ppm
1
Total Frequency Tolerance
-4.6
-
4.6
ppm
2
Operating Temperature Range
0
-
70
C
Supply Voltage
(Vcc)
4.75
5.00
5.25
Vdc
Supply Current
(Icc)
-
-
300
mA
Phase Jitter (BW =12KHz to 20MHz)
-
-
1
pS RMS
Phase Jitter (BW =10Hz to 20MHz)
-
-
3
pS RMS
Period Jitter
-
-
3
pS RMS
SSB Phase Noise at 10Hz offset
-
-75
-
dBc/Hz
SSB Phase Noise at 10KHz offset
-
-130
-
dBc/Hz
Start Up Time: Oscillator
-
-
10
mS
Warm Up Time
-
-
1
Minute
3
TDEV @ 1.0 Sec.
-
-
1
nS
TDEV @ 4.0 Sec.
-
-
2
nS
INPUT CHARACTERISTICS
TABLE 3.0
PARAMETER
MINIMUM
NOMINAL
MAXIMUM
UNITS
NOTE
Control Voltage Range
(Vc)
0.5
2.18
4.1
Vdc
Frequency at Vc=0.5 Vdc
-30
-
-18
ppm
4
Frequency at Vc=4.1 Vdc
18
-
30
ppm
4
Slope of Frequency Adjust
10
-
-
ppm/V
Input Impedance
100k
-
-
Ohm
Enable Voltage
(Vih)
2.0
-
-
Vdc
5
Disable Voltage
(Vil)
-
-
0.8
Vdc
HCMOS OUTPUT CHARACTERISTICS
TABLE 4.0
PARAMETER
MINIMUM
NOMINAL
MAXIMUM
UNITS
NOTE
LOAD
-
-
15
pf
Voltage (High)
(Voh)
4.0
-
-
Vdc
(Low)
(Vol)
-
-
0.4
Vdc
Current (High)
(Ioh)
-4
-
mA
(Low)
(Ioh)
-
-
4
mA
Duty Cycle measured at 1.5V
45
50
55
%
Rise / Fall Time 10% to 90%
-
-
6
nS
Oven Ready Monitor voltage when oven is
cold, not at operating temperature.
Pin 12
-
-
0.4
Vdc
Oven Ready Monitor voltage when oven is
warm, at operating temperature.
Pin 12
3.0
-
-
Vdc
PACKAG E CHARACTERISTICS
TABLE 5.0
Package
14 pin DIP, hermetically sealed, grounded case, welded package
THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
P R O D U C T D A T A S H E E T
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
CRYSTAL CONTROLLED OSCILLATORS
2
2
Cx061
00
8/28/03
www.conwin.com
ENVIRONMENTAL CHARACTERISTICS
Temperature Cycle: Per MIL-STD-883, Method 1010, Condition B. -55C to 125C, 20 cycles,10 minute dwell, 1m inute
transition.
Gross Leak Test: Per MIL-STD-202, Method 112, Condition D. No bubbles in flourinert (FC-43) at 125C 5C for 20
seconds.
SOLDERING
Pin Solderability: Per MIL-STD-883, Method 200. 8 hour steam age prior to 254C 5C Solder pot dip, 95% Coverage.
Resistance to Solder Heat: Per MIL-STD-202, Method 210, Condition C. Wave: Topside board -mount product, 260C
5C for 20 Seconds.
MECHANICAL CHARACTERISTICS
Vibration: Per MIL-STD-202, Method 204, Condition A. 10G's peak, 10Hz to 500Hz, 15mi nute cycles 12 times each
perpendicular axis.
Shock: Per MIL-STD-202, Method 213, Condition D. 500G's, 1ms, half sine, 3 shocks per direction.
Moisture Resistance: Per MIL-STD-202, Method 106. 95% RH @ 65C, 10 cycles 10C to 65C.
1
3
7
8
14
12
CONTROL
VOLTAGE
ENABLE/
DISABLE
OVEN
MONITOR
5.0Vdc
.430 MAX
(10.922mm)
.200
(5.08mm)
PIN
CONNECTION
CONTROL VOLTAGE
ENABLE / DISABLE
GROUND (CASE)
OUTPUT
OVEN MONITOR
+ SUPPLY
1
3
7
8
12
14
W
W
REF.
SUPPLY
4.5Vdc
20K
POT
PDF 
ZIP