THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
P R O D U C T D A T A S H E E T
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
CRYSTAL CONTROLLED OSCILLATORS
The Connor-Winfield
OVA3HA1CB is a
hermetically sealed 14 Pin
DIP 3.3V Oven Controlled,
Voltage Controlled Crystal
Oscillator (OCVCXO) with a
Tri-State HCMOS output.
The
features an
Oven Ready Monitor and is
designed for Stratum 3
applications requiring low
jitter and tight frequency
OVA3HA1CB
1
2
OVA3HA1CB
- 24.057MHz
OCXO
SERIES
CENTER
FREQUENCY
FEATURES
DESCRIPTION
ORDERING INFORMATION
3.3V OPERATION
FREQUENCY ADJUST
TRI-STATE ENABLE / DISABLE
FUNCTION
LOW JITTER <1pS RMS
FREQUENCY STABILITY: 0.25ppm
FREQUENCY TOLERANCE: 4.6ppm
TEMPERATURE RANGE: 0 to 70C
OVEN READY MONITOR
HERMETICALLY SEALED PACKAGE
14 PIN DIP 3.3V HCMOS STRATUM 3 OCVCXO
with OVEN READY MONITOR
Cx085
00
06/17/05
www.conwin.com
OVA3HA1CB
CW 0520
OVA3HA1CB
24.057M
ABSOL UTE M AXIMUM RATING S
TABLE 1.0
PARAMETER
UNITS
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Storage Temperature
-40
-
85
C
Supply Voltage
(Vcc)
-0.5
-
4.5
Vdc
Control Voltage
(Vc)
-0.5
-
4.5
Vdc
OPERATING SPECIFIC ATIONS
TABLE 2.0
PARAMETER
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Center Frequency
(Fo)
1.5
-
40
MHz
Frequency Stability
-0.25
-
0.25
ppm
1
Total Frequency Tolerance
-4.6
-
4.6
ppm
2
Operating Temperature Range
0
-
70
C
Supply Voltage
(Vcc)
3.13
3.3
3.47
Vdc
Supply Current
(Icc)
-
-
450
mA
Phase Jitter (BW =12KHz to Fo/2)
-
-
1
pS RMS
Phase Jitter (BW =10Hz to Fo/2)
-
-
3
pS RMS
Period Jitter
-
-
3
pS RMS
SSB Phase Noise at 10Hz offset
-
-75
-
dBc/Hz
SSB Phase Noise at 10KHz offset
-
-130
-
dBc/Hz
Start Up Time: Oscillator
-
-
10
mS
Warm Up Time
-
-
1
Minute
3
TDEV @ 1.0 Sec.
-
-
1
nS
TDEV @ 4.0 Sec.
-
-
2
nS
INPUT CHARACTERISTICS
TABLE 3.0
PARAMETER
MINIMUM
NOMINAL
MAXIMUM
UNITS
NOTE
Control Voltage Range
(Vc)
0.3
1.65
3.0
Vdc
Frequency at Vc=0.5 Vdc
-22.5
-
-13.5
ppm
4
Frequency at Vc=4.1 Vdc
13.5
-
22.5
ppm
4
Slope of Frequency Adjust
10
-
-
ppm/V
Input Impedance
100k
-
-
Ohm
Enable Voltage (High)
(Vih)
2.0
-
-
Vdc
5
Disable Voltage (Low)
(Vil)
-
-
0.8
Vdc
HCMOS OUTPUT CHARACTERISTICS
TABLE 4.0
PARAMETER
MINIMUM
NOMINAL
MAXIMUM
UNITS
NOTE
LOAD
-
-
15
pf
Voltage (High)
(Voh)
2.6
-
-
Vdc
(Low)
(Vol)
-
-
0.4
Vdc
Current (High)
(Ioh)
-4
-
mA
(Low)
(Ioh)
-
-
4
mA
Duty Cycle measured at 1.5V
45
50
55
%
Rise / Fall Time 10% to 90%
-
-
6
nS
Oven Ready Monitor voltage when oven is
cold, not at operating temperature.
Pin 12
-
-
0.4
Vdc
Oven Ready Monitor voltage when oven is
warm, at operating temperature.
Pin 12
3.0
-
-
Vdc
PACKAG E CHARACTERISTICS
TABLE 5.0
Package
14 pin DIP, hermetically sealed, grounded case, welded package
THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
P R O D U C T D A T A S H E E T
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
CRYSTAL CONTROLLED OSCILLATORS
2
2
Cx085
00
06/17/05
www.conwin.com
ENVIRONMENTAL CHARACTERISTICS
Temperature Cycle: Per MIL-STD-883, Method 1010, Condition B. -55C to 125C, 20 cycles,10 minute dwell, 1m inute
transition.
Gross Leak Test: Per MIL-STD-202, Method 112, Condition D. No bubbles in flourinert (FC-43) at 125C 5C for 20
seconds.
SOLDERING
Pin Solderability: Per MIL-STD-883, Method 200. 8 hour steam age prior to 254C 5C Solder pot dip, 95% Coverage.
Resistance to Solder Heat: Per MIL-STD-202, Method 210, Condition C. Wave: Topside board -mount product, 260C
5C for 20 Seconds.
MECHANICAL CHARACTERISTICS
Vibration: Per MIL-STD-202, Method 204, Condition A. 10G's peak, 10Hz to 500Hz, 15mi nute cycles 12 times each
perpendicular axis.
Shock: Per MIL-STD-202, Method 213, Condition D. 500G's, 1ms, half sine, 3 shocks per direction.
Moisture Resistance: Per MIL-STD-202, Method 106. 95% RH @ 65C, 10 cycles 10C to 65C.
.430 MAX
(10.922mm)
.200
(5.08mm)
PIN
CONNECTION
CONTROL VOLTAGE
ENABLE / DISABLE
GROUND (CASE)
OUTPUT
OVEN MONITOR
+ SUPPLY
1
3
7
8
12
14
1
3
7
8
14
12
CONTROL
VOLTAGE
ENABLE/
DISABLE
OVEN
MONITOR
3.3Vdc
W
W
REF.
SUPPLY
3.0Vdc
20K
POT
Notes:
1) Frequency vs. temperature stability, Vc = 1.65V.
2) Inclusive of calibration, oper ating temperature range, suppl y voltage change, load
change, shock and vibration, 10 years aging, Vc = 1.65V.
3) After one minute of operation at 25
C, the unit will be within +/-0.5ppm of its final
stabilized frequency. The final stabilized frequency is t hat which is measured after 30
minutes of continuous operatio n at a stable 25
C ambient temperature.
4) Referenced to Fo @ 25
C
, Positive Transfer Character istic
5) Oscillator output is enabled with no connection on pin 3.
PDF 
ZIP