THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
WWW.CONWIN.COM
P R O D U C T D A T A S H E E T
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
CRYSTAL CONTROLLED OSCILLATORS
The Connor-Winfield V351 is
a 3.3V Voltage Controlled
Crystal Oscillator (VCXO)
with Differential LVPECL
outputs and Enable/Disable
function. The V351 is
designed for use with PLL
systems in SONET/SDH
systems requiring low jitter
and tight stability. No
multiplication schemes are
used in this oscillator design.
1
2
V351 - 155.52MHz
VCXO
SERIES
CENTER
FREQUENCY
FEATURES
DESCRIPTION
ORDERING INFORMATION
3.3V OPERATION
LOW JITTER <1pS RMS
TOTAL FREQUENCY TOLERANCE:
20ppm
TEMPERATURE RANGE: -40 to 85C
DIFFERENTIAL LVPECL OUTPUTS
ENABLE / DISABLE FUNCTION
SURFACE MOUNT PACKAGE
TAPE AND REEL PACKAGING
3.3V SURFACE MOUNT 5.0 x 7.5mm
LVPECL VCXO OSCILLATOR
V351
Vx536
01
11/07/06
V351 0643
155.5M
ABSOL UTE M AXIMUM RATING S
TABLE 1.0
PARAMETER
UNITS
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Storage Temperature
-55
-
125
C
Supply Voltage
(Vcc)
-0.5
-
7.0
Vdc
Control Voltage
(Vc)
-0.5
-
Vcc+0.5
Vdc
OPERATING SPECIFIC ATIONS
TABLE 2.0
PARAMETER
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Center Frequency
(Fo)
50
-
200
MHz
Total Frequency Tolerance
-20
-
20
ppm
1
Operating Temperature Range
-40
-
85
C
Supply Voltage
(Vcc)
3.135
3.3
3.465
Vdc
Supply Current
(Icc)
-
-
100
mA
Jitter (BW=10Hz to 20MHz)
-
-
5
ps rms
Jitter (BW=12kHz to 80MHz)
-
-
1
ps rms
SSB Phase Noise measurement for 77.76MHz
SSB Phase Noise at 10Hz offset
-
-60
-
dBc/Hz
SSB Phase Noise at 100Hz offset
-
-90
-
dBc/Hz
SSB Phase Noise at 1KHz offset
-
-115
-
dBc/Hz
SSB Phase Noise at 10KHz offset
-
-135
-
dBc/Hz
SSB Phase Noise at 100KHz offset
-
-145
-
dBc/Hz
INPUT CHARACTERISTICS
TABLE 3.0
PARAMETER
MINIMUM
NOMINAL
MAXIMUM
UNITS
NOTE
Control Voltage Range
(Vc)
0.3
1.65
3.0
Vdc
Frequency Pullability @25C
70
-
-
ppm
2
Absolute Pull Range (APR)
50
-
-
ppm
3
Monotonic Linearity
-10
-
10
%
Pin 1 DC Input Resistance
-
60K
-
Ohm
Modulation Bandwidth (3dB)
25
-
-
KHz
Enable Input Voltage (Low)
(Vil)
-
-
1.68
Vdc
4
Disable Input Voltage (High)
(Vih)
2.275
-
-
Vdc
4
LOW VOLTAGE PECL OUTPUT CHARACTERISTICS
TABLE 4.0
PARAMETER
MINIMUM
NOMINAL
MAXIMUM
UNITS
NOTE
LOAD
-
-
50
Ohms
5
Voltage (High)
(Voh)
2.275
-
-
Vdc
(Low)
(Vol)
-
-
1.68
Vdc
Duty Cycle at 50% Level
45
50
55
%
Rise / Fall Time measured @ 20% to 80%
-
0.6
1.5
nS
PACKAG E CHARACTERISTICS
TABLE 5.0
Package
Hermetically sealed crystal mounted on a ceramic package.
PROCESS RECOMMENDATIONS
TABLE 6.0
Soldering Process
See solder profile on page2.
THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
WWW.CONWIN.COM
P R O D U C T D A T A S H E E T
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
CRYSTAL CONTROLLED OSCILLATORS
2
2
Vx536
01
11/07/06
Dimensional Tolerance:
.005 (.127mm)
Pin
Function
1
Control Voltage
2
Enable / Disable
3
Ground (Case)
4
Output Q
5
Comp Output Q
6
Vcc
Notes
1.0
Inclusive of calibration @ 25C, frequency s tability vs. temperature, control v oltage (Vc) = 1.65 Vdc and aging for ten
years.
2.0
Referenced to Fo at T=25C Positive Slope.
3.0
Absolute pull range (APR) is the minim um guaranteed pull range of the VCXO under all conditions over lifeti me operation
including aging for ten years. The APR is referenced to Fo.
4.0
When oscillator is dis abled both output are in a high impedance state (Tri -State)
5.0
50 ohm termination into Vcc -2V or Thevein equivalent.
120
C
150
C
180
C
260
C
0
220
C
360 Sec. Max.
120 S
Max.
10 S
60 S
Max.
Time
Temperature
260C
Solder Profile
1.65V
E/D
2
Vcc = Vcc2 = 3.3Vdc
V
3
5
1
0
6
4
3
1
5
5
.
5
M
Test Circuit
Suggested Pad Layout
Output Waveform
Pin Connections
Package Outline
PDF 
ZIP