The Connor-Winfield
VSPLD63TE is a 3.3V Voltage
Controlled SAW Oscillator
(VCSO) with Differential LVPECL
outputs and Enable/Disable
function. The VSPLD63TE is
designed for use with PLL
systems in SONET/SDH systems
requiring low jitter and wide pull
range over the industrial
temperature range. No
multiplication schemes are used
in this oscillator design.
1
2
VSPLD63TE - 622.08MHz
VCSO
SERIES
CENTER
FREQUENCY
FEATURES
DESCRIPTION
ORDERING INFORMATION
VOLTAGE CONTROLLED SAW
OSCILLATOR
LOW PROFILE, SURFACE MOUNT
PACKAGE
3.3V OPERATION
LOW JITTER <0.5pS RMS
ABSOLUTE PULL RANGE (APR): 50ppm
TEMPERATURE RANGE: -40 to 85C
DIFFERENTIAL LVPECL OUTPUTS
ENABLE / DISABLE FUNCTION
TAPE AND REEL PACKAGING
RoHS 5/6 COMPLIANT
3.3V SURFACE MOUNT VCSO OSCILLATOR
VSPLD63TE
Vs001
01
9/29/06
CW 0639
VSPLD63TE
622.08M
THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
WWW.CONWIN.COM
P R O D U C T D A T A S H E E T
CRYSTAL CONTROLLED OSCILLATORS
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
ABSOL UTE M AXIMUM RATING S
TABLE 1.0
PARAMETER
UNITS
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Storage Temperature
-55
-
125
C
Supply Voltage
(Vcc)
-0.5
-
7.0
Vdc
Control Voltage
(Vc)
-0.5
-
7.0
Vdc
OPERATING SPECIFIC ATIONS
TABLE 2.0
PARAMETER
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Center Frequency
(Fo)
-
622.08
-
MHz
Frequency Stability
-
+/-150
-
ppm
1
Operating Temperature Range
-40
-
85
C
Supply Voltage
(Vcc)
3.135
3.3
3.465
Vdc
Supply Current
(Icc)
-
-
80
mA
Jitter (BW=10Hz to 20MHz)
-
-
3.0
ps rms
Jitter (BW=12kHz to 80MHz)
-
-
0.5
ps rms
SSB Phase Noise at 100Hz offset
-
-70
-
dBc/Hz
SSB Phase Noise at 1KHz offset
-
-105
-
dBc/Hz
SSB Phase Noise at 10KHz offset
-
-145
-
dBc/Hz
SSB Phase Noise at 100KHz offset
-
-155
-
dBc/Hz
INPUT CHARACTERISTICS
TABLE 3.0
PARAMETER
MINIMUM
NOMINAL
MAXIMUM
UNITS
NOTE
Control Voltage Range
(Vc)
0.3
1.65
3.0
Vdc
Absolute Pull Range (APR)
+/-50
-
-
ppm
2
Gain Transfer (Kv)
-
175
-
ppm/volt
Monotonic Linearity
-15
-
15
%
Input Impedance
-
50K
-
Ohm
Modulation Bandwidth (3dB)
10
-
-
KHz
Enable Input Voltage (Low)
(Vil)
-
-
1.68
Vdc
3
Disable Input Voltage (High)
(Vih)
2.275
-
-
Vdc
3
LOW VOLTAGE PECL OUTPUT CHARACTERISTICS
TABLE 4.0
PARAMETER
MINIMUM
NOMINAL
MAXIMUM
UNITS
NOTE
LOAD
-
-
50
Ohms
4
Voltage (High)
(Voh)
2.275
-
-
Vdc
(Low)
(Vol)
-
-
1.68
Vdc
Duty Cycle at 50% Level
45
50
55
%
Rise and fall times (Measured 20% to 80%)
-
250
400
ps
PACKAG E CHARACTERISTICS
TABLE 5.0
Package
Non-hermetic package consisting of an FR4 substrate with grounded metal
cover.
PROCESS RECOMMENDATIONS
TABLE 6.0
Soldering Process
See solder profile page 2.
Wash
Ultrasonic cleaning is not recommended.
Notes
1.0
I Frequency stability vs. change in temperature, control voltage (Vc) = 1.65 Vdc.
2.0
Control voltage for (Fo) = 1.65 Vdc Typical. Positive Transfer Function.
3.0
When oscillator is disabled the pin 4 output is in a low state (Vol) and the pin 5 output is in the high state (VoH)
4.0
50 ohm termination into Vcc-2V or Thevein equivalent.
2
2
Vs001
01
9/29/06
Dimensional Tolerance:
.005 (.127mm)
.140 MAX
.140 MAX
(3.56mm)
(3.56mm)
V
S
P
L
D
6
3
T
E
6
2
2
.
0
8
M
C
W
C
W
100
C
150
C
225
C
25C
183C
360 Sec. Max.
60-120s
Max.
60-150s Max.
Time
Temperature
225C
0
tp
Ramp-Down Rate
6C/second max.
10-30s
Ramp-Up Rate
3C/second max.
from 150C to 225C.
Package Outline
Pin Connections
Output Waveform
Suggested Pad Layout
Test Circuit
Solder Profile
THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
WWW.CONWIN.COM
P R O D U C T D A T A S H E E T
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
CRYSTAL CONTROLLED OSCILLATORS
TABLE 7.0
Pin
Function
1
Control Voltage
2
Enable / Disable
3
Ground (Case)
4
Output Q
5
Output Q
6
Vcc
1.65V
E/D
2
Vcc = Vcc2 = 3.3Vdc
PDF 
ZIP