2-28
Dialight Corporation 1501 Route 34 South Farmingdale, NJ 07727 TEL: (732) 919-3119 FAX: (732) 751-5778 www.dialight.com
515-1056-801
FRONT END
SOLDER PAD/HOLES LAYOUT
23.95
[.943]
.003
13.89
[.547]
.003
1.83 [.072]
4.83 [.190]
7.62 [.300]
1.06 [.418]
2.59
[.102]
TYP
1.09
[.043]
TYP
1.52
[.060]
TYP
1.09
[.076]
.002
4 PLCS
3.71
[.146]
8.79
[.346]
17.75
[.699]
22.83
[.899]
5.08
[.200]
2.03
[.080]
(REF)
13.89
[.547]
3.18
[1.253]
.254
[.010]
515-1057
515-1056
MOUNTING BRACKETS
DIALIGHT P/N'S:
515-1058 (ONE POSITION JACK; 4-ACROSS LIGHTPIPE)
515-1059 (TWO POSITION JACK; 3-ACROSS LIGHTPIPE)
515-1060 (THREE POSITION JACK; 12-ACROSS LIGHTPIPE)
5.79
[.228]
4.06
[.160]
58.42
[.2.30]
* PEM NUT REQUIRED FOR MOUNTING: PEM 55-156-8
6.32
[.249]
7.01
[.276]
2.54 [.100]
SQR TYP;
23.95
[.943]
3.30
[.130]
TYP
36.91
[1.453]
5.08
[.200]
TYP
14.02
[.552]
4.47
[.176]
27.43
[1.08]
28.04
[1.104]
2.54
[.10]
38.35
[1.51]
(REF)
(FRONT PANEL AND MOUNTING/ALIGNMENT
COMPONENT NOT SHOWN IN THIS VIEW)
7.01
[.276]
HOLES FOR
PEM NUTS
Dimensions in mm [inches]
Recommended
MicroLED SMT LEDs
for use with 515-1056, 515-
1057 & 515-1056-801
PART NO.
COLOR
PAGE#
597-3001-2xx
Red
1-21
597-3111-5xx
AlGaAsRed
1-30
597-3121-2xx
AlGaAsRed
1-21
597-3211-2xx
Orange
1-21
597-3211-5xx
Orange
1-30
597-3301-2xx
Green
1-21
597-3301-5xx
Green
1-30
597-3401-2xx
Yellow
1-21
597-3401-5xx
Yellow
1-30
597-7701-2xx
Red/Green
1-23
597-7701-5xx
Red/Green
1-31
597-7721-2xx
Yellow/Green
1-23
597-7721-5xx
Yellow/Green
1-31
597-7731-2xx
Red/Green
1-24
0.100 x 0.100 Square
Optopipe
TM
Optical Light Pipe, 4 Array
(Dual High RJ45)
Features
Allows for 2 separate indicators for each part on a dual high RJ45 Jack
High transmissivity polycarbonate material
UL94V-0 compliance
ESD protection (circuit isolation from front panel)
Wide viewing angle
Arrays reduce insertion costs
Secures to PCB by snap-fit
Hardware
:
515-1058 (One position)*
515-1059 (Two position)*
515-1060 (Three position)*
*Position refers to one dual high, dual wide RJ45 connector
LED Data
For absolute maximum ratings and other electrical and
optical data on the recommended LEDs, refer to the LED
data Sheets
Dialight
Optopipe
Light Pipe Description
This OptopipeTM functions as a through-the-case indicator by conducting the light over the top of connectors or
switches. This Optopipe'sTM eight 0.100 x 0.100 square light emitting surfaces appear bright and are optically well
isolated. This light pipe is reliably held in place by 4 press-fit pins located near the outer elements. These pins press fit
onto 0.062" thick PCBs regardless of individual variations in thickness. A textured finish on the 8 light emitting surfaces
maximizes the viewing angle. The recommended light sources are Dialight's 597 Series PLCC-2 or PLCC-4 Type SMT
LEDs. The light pipe material is water clear transmissive polycarbonate rated UL94-V0, and has a 35% oxygen index.
Dialight can provide custom Optopipe (tm) solutions for your applications.
Operating/Storage Temperature
30C to +100C
NEW
PDF 
ZIP