515-1061
2-43
Dialight Corporation 1501 Route 34 South Farmingdale, NJ 07727 TEL: (732) 919-3119 FAX: (732) 751-5778 www.dialight.com
2
3mm Round
Optopipe
TM
Optical Light Pipe, Bi-Level
13.97
[.55]
2.54
[.100]
1.91
[.075]
REF
7.62
[.300]
1.57
[.062]
DIFFUSED FRONT
SURFACES;
2 PLCS
5.08
[.200]
2.54
[.100]
.25
[.010]
7.87
[.310]
5.12
[.200]
2.54
[.100]
1.63
[.064]
MOUNTING
PIN
9.14
[.36]
2.79
[.11]
4.57
[.18]
3.05
[.120]
1.52
[.06]
3.05
[.120] TYP
2 PLCS
5.12
[.200]
2.29
[.090]
4.50
[.177]
1.45
[.057]
TYP
1.60
[.063]
TYP
[ .060
.002]
TYP, 2 PLCS
2.54
.05
[.100
.002]
3.35
[.132]
4.27
[.168]
4.39
[.173]
4.50
[.177]
TYP
1.04
[.041]
TYP
3.89
[.153]
2.69
[.106]
TYP
2.54
.05
[.100
.002]
3.73
[.147]
4.39
[.173]
TYP
FIGURE A
(USING SINGLE COLOR SMT LEDS)
FIGURE B
(USING BI-COLOR SMT LEDS)
THIS VIEW SHOWS TWO 515-1061
LIGHT PIPES MOUNTED
SIDE BY SIDE
1.52
.05
[.060
.002]
TYP, 2 PLCS
DIRECTION
OF LIGHT
DIRECTION
OF LIGHT
RECOMMENDED SOLDER PAD/HOLES LAYOUT
RECOMMENDED SOLDER PAD/HOLES LAYOUT
FRONT
PANEL
Dimensions in mm [inches]
Recommended
MicroLED SMT LEDs
for use with 515-1061
PART NO.
COLOR
PAGE #
597-3111-5xx
AlGaAs Red
1-30
597-3211-5xx
Orange
1-30
597-3301-5xx
Green
1-30
597-3401-5xx
Yellow
1-30
597-7701-5xx
Red/Green
1-31
597-7721-5xx
Yellow/Green
1-31
Features
Can be mounted in arrays spaced .200 apart (min.)
High transmissivity polycarbonate material
UL94V-0 compliance
ESD protection (circuit isolation from front panel)
Wide viewing angle
Arrays reduce insertion costs
Allows bi-level SMT indicators
Secures to PCB by press-fit
LED Data
For absolute maximum ratings and other
electrical and optical data on the recommended
LEDs, refer to LED data sheets.
Dialight
Optopipe
Light Pipe Description
This OptopipeTM is a standard design intended as a SMT compatible replacement for our 553 Series Circuit Board
Indicators. The light outputs are spaced vertically .100" from the PCB to the first element, and then 0.200" between the top
and bottom elements. We recommend a minimum of 0.200" between light pipes as a normal mounting pitch. This
OptopipeTM is held in place by 2 press-fit pins along the bottom of the device. The light pipe is not attached to the panel at
any point but can protrude through holes in the panel. The gently arcing emitting end sticks through the plastic or metal
panel. The light source is Dialight's 597 Series Type 1208 LED. The light pipe material is water clear transmissive
polycarbonate rated UL94-V0, and has a 35% oxygen index.
Dialight can provide custom OptopipeTM solutions for your applications.
Operating/Storage Temperature
30C to +100C
NOTE: designed for
post-reflow
PC board insertion.
PDF 
ZIP