MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS
FEATURES
Data Sheet No. FSPD-100-1B
MECHANICAL SPECIFICATION
Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.
Tel.: (310) 767-1052
Fax: (310) 767-7958
DIOTEC ELECTRONICS CORP.
Gardena, CA 90248
U.S.A
18020 Hobart Blvd., Unit B
Average Forward Rectified Current @ T = 75 C,
Lead length = 0.375 in. (9.5 mm)
A
o
PARAMETER (TEST CONDITIONS)
Maximum DC Blocking Voltage
Peak Forward Surge Current ( 8.3 mSec single half sine wave
superimposed on rated load)
Maximum Forward Voltage at 1 Amp DC
Typical Thermal Resistance, Junction to Ambient (Note 1)
Operating and Storage Temperature Range
Maximum Average DC Reverse Current
At Rated DC Blocking Voltage
Maximum Peak Recurrent Reverse Voltage
Maximum RMS Voltage
Series Number
I
RM
T
RR
R
JA
T T
J,
STG
I
O
V
RMS
V
RRM
V
RM
SYMBOL
RATINGS
VOLTS
C/W
C
AMPS
UNITS
VOLTS
A
V
FM
I
FSM
Typical Junction Capacitance (Note 2)
C
J
pF
200
400
140
280
200
800
560
800
400
1
50
1.2
150
0.5
25
15
-65 to +175
4.97ffspd100
(1) Lead length = 0.375 in. (9.5 mm)
(2) Measured at 1MHz & applied reverse voltage of 4 volts
(3) 300nS avaiable - consult factory
NOTES:
@ T = 25 C
A
o
@ T = 100 C
A
o
Case: JEDEC DO-41, molded silica glass
(U/L Flammability Rating 94V-0)
Terminals: Plated axial leads
Soldering: Per MIL-STD 202E Method 208 guaranteed
Polarity: Color band denotes cathode
Mounting Position: Any
Weight: 0.012 Ounces (0.34 Grams)
H27
MECHANICAL DATA
ACTUAL SIZE OF
DO-41 PACKAGE
Sym
In
mm
Minimum
Maximum
BL
BD
LL
LD
1.00
0.028
In
mm
0.107
0.205
0.034
5.2
2.7
0.86
0.160
0.103
25.4
0.71
4.1
2.6
Color Band
Denotes
Cathode
LD (Dia)
BD (Dia)
LL
BL
LL
Maximum Reverse Recovery Time (I =0.5A, I =1A, I
=0.25A)
F
R
RR
100
101
102
104
106
108
110
50
35
50
100
70
100
600
420
600
1000
700
1000
SERIES RGP100 - RGP110
250
500 (Note 3)
nS
DO - 41
55
RGP
RGP
RGP
RGP
RGP
RGP
RGP
EXTREMELY LOW LEAKAGE AT HIGH TEMPERATURES
LOW FORWARD VOLTAGE DROP
1A at T = 75 C WITH NO THERMAL RUNAWAY
A
o
VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM
MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)
R
PROPRIETARY
JUNCTION
PASSIVATION FOR SUPERIOR RELIABILITY AND
PERFORMANCE
SOFT GLASS
RATING & CHARACTERISTIC CURVES FOR SERIES RGP100 - RGP110
Data Sheet No. FSPD-100-2B
Tel.: (310) 767-1052
Fax: (310) 767-7958
DIOTEC ELECTRONICS CORP.
Gardena, CA 90248
U.S.A
18020 Hobart Blvd., Unit B
FIGURE 2. MAXIMUM NON-REPETITIVE SURGE CURRENT
Number of Cycles at 60 Hz
1
10
100
50
40
30
20
10
0
1 AMP HIGH RELIABILITY FAST RECOVERY DIODES
4.97bfspd100
H28
FIGURE 3. TYPICAL FORWARD CHARACTERISTIC
Instantaneous Forward Voltage (Volts)
0.01
0.1
1.0
10
10
FIGURE 4. TYPICAL JUNCTION CAPACITANCE
Reverse Voltage, (Volts)
1
0.1
10
0.1
100
Pulse Width = 300 S
1% Duty Cycle
JEDEC Method
8.3 mS Half Sine Wave
T = 175 C
J
o
T = 25 C
f = 1 MHz
V
= 50 mV P-P
J
SIG
o
NOTES:
(1) Rise time = 7nS max., input impedance = 1 Megohm, 22 pF
(2) Rise time = 10nS max., source impedance = 50 ohms
FIGURE 5. REVERSE RECOVERY TEST SETUP AND TIME CHARACTERISTIC
1
non-
inductive
10
noninductive
50
noninductive
OSCILLOSCOPE
(Note 1)
PULSE
GENERATOR
(Note 2)
(+)
(+)
(-)
(-)
D.U.T.
25 VDC
(APPROX)
-1.0
-0.5
0.0
0.5
Set time base
for 10nS/cm
1
cm
T
RR
FIGURE 1. FORWARD CURRENT DERATING CURVE
Ambient Temperature, C
o
Single Phase, Half wave, 60 Hz
Resistive and Inductive Loads
Lead Length = 0.375" (9.5 mm)
T =25 C
J
o
T =150 C
J
o
PDF 
ZIP