MECHANICAL DATA
FEATURES
Data Sheet No. FRDB-3500P-1B
MECHANICAL SPECIFICATION
PRV Ratings from 50 to 1000 Volts
Surge overload rating to 400 Amps peak
Reliable low cost molded plastic construction
Ideal for printed circuit board applications
Fast switching for high efficiency
MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS
Ratings at 25 C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive loads, derate current by 20%.
Average Forward Rectified Current @ T = 55 C
C
o
PARAMETER (TEST CONDITIONS)
Maximum DC Blocking Voltage
Maximum Peak Recurrent Reverse Voltage
Maximum RMS Voltage
Series Number
I
O
V
RMS
V
RRM
V
RM
SYMBOL
FDB
FDB
RATINGS
UNITS
VOLTS
FDB
FDB
FDB
FDB
FDB
50
100
200
400
1000
35
70
140
280
700
35
Peak Forward Surge Current (8.3mS single half sine wave
superimposed on rated load)
Maximum Forward Voltage, Per Diode, at 17.5 Amps DC
VOLTS
AMPS
V
FM
I
FSM
400
1.3
Maximum Average DC Reverse Current at Rated
DC Blocking Voltage Per Diode (Note 2)
I
RM
A
@ T = 25 C
A
o
@ T = 100 C
A
o
10
1
T
RR
G17
R
JC
C/W
1.2
Typical Thermal Resistance, Junction to Case (Note 2)
Operating and Storge Temperature Range
T T
J,
STG
C
-55 to +150
3.0135fdbp
(1) T =25 C, I =0.5A, I =1A, I
=0.25A
(2)
J
F
R
RR
o
Bridge mounted on an 9" x 3" x 4.6" thick (22.9cm x 7.6cm x 11.7cm) finned aluminum plate
NOTES:
600
800
50
100
200
400
1000
600
800
420
560
3500P 3501P 3502P 3504P 3506P 3508P 3510P
Maximum Reverse Recovery Time (Note 1)
200
300
500
nS
Thermal Energy (Rating for Fusing, t < 8.3 mS)
I t
2
664
AMPS
2
SEC
mA
Case: Molded plastic, U/L Flammability Rating 94V-0
Terminals: Round silver plated copper pins or fast-on terminals
Soldering: Per MIL-STD 202 Method 208 guaranteed
Polarity: Marked on side of case
Mounting Position: Any. Through hole for #8 screw.
Weight: Fast-on Terminals - 0.7 Ounces (20.0 Grams)
Max. mounting torque = 20 in-lb.
Wire Leads - 0.55 Ounces (16.0 Grams)
SERIES FDB3500P - FDB3510P
Suffix "T" indicates FAST-ON TERMINALS
Suffix "W" indicates WIRE LEADS
D3
D1
D1
BL
HOLE FOR
#8 SCREW
D2
BL
BH
LT
HOLE FOR
#8 SCREW
LD
LL
BH
D1
D2
BL
D1
BL
Top View of
HeatSink
Suffix "P" indicates molded PLASTIC with intergrally mounted Heat Sink
Heat Sink
+
_
AC
AC
UL RECOGNIZED - FILE #E141956
Tel.: (310) 767-1052
Fax: (310) 767-7958
DIOTEC ELECTRONICS CORP.
Gardena, CA 90248
U.S.A
18020 Hobart Blvd., Unit B
PDF 
ZIP