RGP02-12E // 20E
HIGH VOLTAGE
FAST RECOVERY RECTIFIERS
PRV : 1200 - 2000 Volts
Io : 0.5 Ampere
FEATURES :
* Glass passivated junction
* High current capability
* High surge current capability
* High reliability
* Low reverse current
* Low forward voltage drop
* Fast switching for high efficiency
MECHANICAL DATA :
* Case : DO-41 Molded plastic
* Epoxy : UL94V-O rate flame retardant
* Lead : Axial lead solderable per MIL-STD-202,
Method 208 guaranteed
* Polarity : Color band denotes cathode end
* Mounting position : Any
* Weight : 0.339 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25
C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
SYMBOL
RGP
02-12E
RGP
02-14E
RGP
02-16E
RGP
02-18E
RGP
02-20E
UNITS
Maximum Recurrent Peak Reverse Voltage
V
RRM
1200
1400
1600
1800
2000
Volts
Maximum RMS Voltage
V
RMS
840
980
1120
1260
1400
Volts
Maximum DC Blocking Voltage
V
DC
1200
1400
1600
1800
2000
Volts
Maximum Average Forward Current
0.375"(9.5mm) Lead Length Ta = 55
C
I
F(AV)
0.5
Amps.
Peak Forward Surge Current 8.3 ms. Single half sine wave
Superimposed on rated load (JEDEC Method)
I
FSM
20
Amps.
Maximum Peak Forward Voltage at 0.5 Amp.
V
F
2.5
Volts
Maximum DC Reverse Current Ta = 25
C
I
R
5.0
A
at Rated DC Blocking Voltage Ta = 100
C
I
R(H)
50
A
Maximum Reverse Recovery Time ( Note 1 )
Trr
300
ns
Typical Junction Capacitance ( Note 2 )
C
J
5.0
pf
Junction Temperature Range
T
J
- 65 to + 150
C
Storage Temperature Range
T
STG
- 65 to + 150
C
Notes :
( 1 ) Reverse Recovery Test Conditions : I
F
= 0.5 A, I
R
= 1.0 A, Irr = 0.25 A.
( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 V
DC
UPDATE : APRIL 23, 1998
RATING
DO - 41
Dimensions in inches and ( millimeters )
1.00 (25.4)
MIN.
0.107 (2.7)
0.080 (2.0)
0.205 (5.2)
0.166 (4.2)
1.00 (25.4)
MIN.
0.034 (0.86)
0.028 (0.71)
RATING AND CHARACTERISTIC CURVES ( RGP02-12E - RGP02-20E )
FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
+
NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF.
2. Rise time = 10 ns max., Source Impedance = 50 ohms.
3. All Resistors = Non-inductive Types.
FIG.2 - DERATING CURVE FOR OUTPUT
FIG.3 - MAXIMUM NON-REPETITIVE PEAK
RECTIFIED CURRENT
FORWARD SURGE CURRENT
0
25
50
75
100
125
150
175
1
2
4
6
10
20
40
60 100
AMBIENT TEMPERATURE, (
C)
NUMBER OF CYCLES AT 60Hz
FIG.4 - TYPICAL FORWARD CHARACTERISTICS
FIG.5 - TYPICAL REVERSE CHARACTERISTICS
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
2.2
2.4
2.6
FORWARD VOLTAGE, VOLTS
60Hz RESISTIVE OR INDUCTIVE LOAD
0.4
0.3
0.2
0.1
0.5
2.0
10
1.0
20
0
25
0
15
10
5
0.01
1.0
80
0.001
0.01
0.1
0.1
100
140
0
20
40
60
120
PERCENT OF RATED REVERSE
VOLTAGE, (%)
PEAK FORWARD SURGE
CURRENT, AMPERES
AVERAGE FORWARD OUTPUT
CURRENT, AMPERES
FORWARD CURRENT, AMPERES
REVERSE CURRENT, MICROAMPERES
T
J
= 25
C
T
J
= 100
C
T
J
= 25
C
Pulse Width = 300
s
2% Duty Cycle
8.3 ms SINGLE HALF SINE WAVE
Ta = 50
C
SET TIME BASE FOR 50/100 ns/cm
Trr
+ 0.5 A
0
- 0.25
- 1.0 A
1 cm
OSCILLOSCOPE
( NOTE 1 )
1
50
10
D.U.T.
50 Vdc
(approx)
PULSE
GENERATOR
( NOTE 2 )
PDF 
ZIP