ChipFind - документация

Электронный компонент: HB54A5129F1

Скачать:  PDF   ZIP

Document Outline

Document No. E0090H40 (Ver. 4.0)
Date Published August 2002 (K) Japan
URL: http://www.elpida.com
Elpida Memory,Inc. 2001-2002
Hitachi, Ltd. 2000
Elpida Memory, Inc. is a joint venture DRAM company of NEC Corporation and Hitachi, Ltd.
DATA SHEET
512MB Registered DDR SDRAM DIMM
HB54A5129F1-A75B/B75B/10B
(64M words



72 bits, 1 Bank)
Description
The HB54A5129F1 is a 64M
72
1 bank Double
Data Rate (DDR) SDRAM Module, mounted 18 pieces
of 256Mbits DDR SDRAM (HM5425401BTT) sealed in
TSOP package, 1 piece of PLL clock driver, 2 pieces of
register driver and 1 piece of serial EEPROM (2k bits
EEPROM) for Presence Detect (PD). Read and write
operations are performed at the cross points of the CK
and the /CK. This high-speed data transfer is realized
by the 2-bit prefetch-pipelined architecture. Data
strobe (DQS) both for read and write are available for
high speed and reliable data bus design. By setting
extended mode register, the on-chip Delay Locked
Loop (DLL) can be set enable or disable. An outline of
the products is 184-pin socket type package (dual lead
out). Therefore, it makes high density mounting
possible without surface mount technology. It provides
common data inputs and outputs. Decoupling
capacitors are mounted beside each TSOP on the
module board.
Features
184-pin socket type package (dual lead out)
Outline: 133.35mm (Length)
43.18 (Height)
4.00mm (Thickness)
Lead pitch: 1.27mm
2.5V power supply (VCC/VCCQ)
SSTL-2 interface for all inputs and outputs
Clock frequency: 143MHz/133MHz/125MHz (max.)
Data inputs and outputs are synchronized with DQS
4 banks can operate simultaneously and
independently (Component)
Burst read/write operation
Programmable burst length: 2, 4, 8
Burst read stop capability
Programmable burst sequence
Sequential
Interleave
Start addressing capability
Even and Odd
Programmable /CAS latency (CL): 3, 3.5
8192 refresh cycles: 7.8
s (8192/64ms)
2 variations of refresh
Auto refresh
Self refresh
HB54A5129F1-A75B/B75B/10B
Data Sheet E0090H40 (Ver. 4.0)
2
Ordering Information

Part number
Clock frequency
MHz (max.)

/CE latency

Package

Contact pad
HB54A5129F1-A75B*
1
HB54A5129F1-B75B*
2
HB54A5129F1-10B*
133
133
100
3.0
3.5
3.0
184-pin dual lead out socket
type
Gold
Notes: 1. 143MHz operation at /CAS latency = 3.5.
2. 100MHz operation at /CAS latency = 3.0.
3. 125MHz operation at /CAS latency = 3.5.
Pin Configurations
1 pin
Front side
Back side
52 pin 53 pin
92 pin
93 pin
144 pin 145 pin 184 pin
Pin No.
Pin name
Pin No.
Pin name
Pin No.
Pin name
Pin No.
Pin name
1
VREF
47
DQS8
93
VSS
139
VSS
2
DQ0
48
A0
94
DQ4
140
DM8/DQS17
3
VSS
49
CB2
95
DQ5
141
A10
4
DQ1
50
VSS
96
VCCQ
142
CB6
5
DQS0
51
CB3
97
DM0/DQS9
143
VCCQ
6
DQ2
52
BA1
98
DQ6
144
CB7
7
VCC
53
DQ32
99
DQ7
145
VSS
8
DQ3
54
VCCQ
100
VSS
146
DQ36
9
NC
55
DQ33
101
NC
147
DQ37
10
/RESET
56
DQS4
102
NC
148
VCC
11
VSS
57
DQ34
103
NC
149
DM4/DQS13
12
DQ8
58
VSS
104
VCCQ
150
DQ38
13
DQ9
59
BA0
105
DQ12
151
DQ39
14
DQS1
60
DQ35
106
DQ13
152
VSS
15
VCCQ
61
DQ40
107
DM1/DQS10
153
DQ44
16
NC
62
VCCQ
108
VCC
154
/RAS
17
NC
63
/WE
109
DQ14
155
DQ45
18
VSS
64
DQ41
110
DQ15
156
VCCQ
19
DQ10
65
/CAS
111
NC
157
/S0
20
DQ11
66
VSS
112
VCCQ
158
NC
21
CKE0
67
DQS5
113
NC
159
DM5/DQS14
22
VCCQ
68
DQ42
114
DQ20
160
VSS
23
DQ16
69
DQ43
115
A12
161
DQ46
24
DQ17
70
VCC
116
VSS
162
DQ47
25
DQS2
71
NC
117
DQ21
163
NC
26
VSS
72
DQ48
118
A11
164
VCCQ
27
A9
73
DQ49
119
DM2/DQS11
165
DQ52
28
DQ18
74
VSS
120
VCC
166
DQ53
HB54A5129F1-A75B/B75B/10B
Data Sheet E0090H40 (Ver. 4.0)
3
Pin No.
Pin name
Pin No.
Pin name
Pin No.
Pin name
Pin No.
Pin name
29
A7
75
NC
121
DQ22
167
NC
30
VCCQ
76
NC
122
A8
168
VCC
31
DQ19
77
VCCQ
123
DQ23
169
DM6/DQS15
32
A5
78
DQS6
124
VSS
170
DQ54
33
DQ24
79
DQ50
125
A6
171
DQ55
34
VSS
80
DQ51
126
DQ28
172
VCCQ
35
DQ25
81
VSS
127
DQ29
173
NC
36
DQS3
82
VCCID
128
VCCQ
174
DQ60
37
A4
83
DQ56
129
DM3/DQS12
175
DQ61
38
VCC
84
DQ57
130
A3
176
VSS
39
DQ26
85
VCC
131
DQ30
177
DM7/DQS16
40
DQ27
86
DQS7
132
VSS
178
DQ62
41
A2
87
DQ58
133
DQ31
179
DQ63
42
VSS
88
DQ59
134
CB4
180
VCCQ
43
A1
89
VSS
135
CB5
181
SA0
44
CB0
90
NC
136
VCCQ
182
SA1
45
CB1
91
SDA
137
CK0
183
SA2
46
VCC
92
SCL
138
/CK0
184
VCCSPD
HB54A5129F1-A75B/B75B/10B
Data Sheet E0090H40 (Ver. 4.0)
4
Pin Description
Pin name
Function
A0 to A12
Address input
Row address
A0 to A12
Column address
A0 to A9, A11
BA0, BA1
Bank select address
DQ0 to DQ63
Data input/output
CB0 to CB7
Check bit (Data input/output)
/RAS
Row address strobe command
/CAS
Column address strobe command
/WE
Write enable
/S0
Chip select
CKE0
Clock enable
CK0
Clock input
/CK0
Differential clock input
DQS0 to DQS8
Input and output data strobe
DM0 to DM8/DQS9 to DQS17
Input and output data strobe
SCL
Clock input for serial PD
SDA
Data input/output for serial PD
SA0 to SA2
Serial address input
VCC
Power for internal circuit
VCCQ
Power for DQ circuit
VCCSPD
Power for serial EEPROM
VREF
Input reference voltage
VSS
Ground
VCCID
VCC identification flag
/RESET
Reset pin (forces register inputs low)
NC
No connection
HB54A5129F1-A75B/B75B/10B
Data Sheet E0090H40 (Ver. 4.0)
5
Serial PD Matrix*
1
Byte No.
Function described
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 Hex value
Comments
0
Number of bytes utilized by module
manufacturer
1
0
0
0
0
0
0
0
80
128
1
Total number of bytes in serial PD
device
0
0
0
0
1
0
0
0
08
256 byte
2
Memory type
0
0
0
0
0
1
1
1
07
SDRAM DDR
3
Number of row address
0
0
0
0
1
1
0
1
0D
13
4
Number of column address
0
0
0
0
1
0
1
1
0B
11
5
Number of DIMM banks
0
0
0
0
0
0
0
1
01
1
6
Module data width
0
1
0
0
1
0
0
0
48
72 bits
7
Module data width continuation
0
0
0
0
0
0
0
0
00
0 (+)
8
Voltage interface level of this assembly 0
0
0
0
0
1
0
0
04
SSTL 2.5V
9
DDR SDRAM cycle time, CL = X
-A75B
0
1
1
1
0
0
0
0
70
CL = 2.5*
5
-B75B
0
1
1
1
0
1
0
1
75
-10B
1
0
0
0
0
0
0
0
80
10
SDRAM access from clock (tAC)
-A75B/B75B
0
1
1
1
0
1
0
1
75
0.75ns*
5
-10B
1
0
0
0
0
0
0
0
80
0.8ns*
5
11
DIMM configuration type
0
0
0
0
0
0
1
0
02
ECC
12
Refresh rate/type
1
0
0
0
0
0
1
0
82
7.8 s
Self refresh
13
Primary SDRAM width
0
0
0
0
0
1
0
0
04
4
14
Error checking SDRAM width
0
0
0
0
0
1
0
0
04
4
15
SDRAM device attributes:
Minimum clock delay back-to-back
column access
0
0
0
0
0
0
0
1
01
1 CLK
16
SDRAM device attributes:
Burst length supported
0
0
0
0
1
1
1
0
0E
2, 4, 8
17
SDRAM device attributes: Number of
banks on SDRAM device
0
0
0
0
0
1
0
0
04
4
18
SDRAM device attributes:
/CAS latency
0
0
0
0
1
1
0
0
0C
2/2.5
19
SDRAM device attributes:
/CS latency
0
0
0
0
0
0
0
1
01
0
20
SDRAM device attributes:
/WE latency
0
0
0
0
0
0
1
0
02
1
21
SDRAM module attributes
0
0
1
0
0
1
1
0
26
Registered
22
SDRAM device attributes: General
1
1
0
0
0
0
0
0
C0
0.2V
23
Minimum clock cycle time at
CLX - 0.5
-A75B
0
1
1
1
0
1
0
1
75
CL = 2*
5
-B75B/10B
1
0
1
0
0
0
0
0
A0
24
Maximum data access time (tAC) from
clock at CLX - 0.5
-A75B/B75B
0
1
1
1
0
1
0
1
75
0.75ns*
5
-10B
1
0
0
0
0
0
0
0
80
0.8ns*
5
25
Minimum clock cycle time at
CLX - 1
0
0
0
0
0
0
0
0
00
26
Maximum data access time (tAC) from
clock at CLX - 1
0
0
0
0
0
0
0
0
00
27
Minimum row precharge time (tRP)
0
1
0
1
0
0
0
0
50
20ns
HB54A5129F1-A75B/B75B/10B
Data Sheet E0090H40 (Ver. 4.0)
6
Byte No.
Function described
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 Hex value
Comments
28
Minimum row active to row active
delay (tRRD)
0
0
1
1
1
1
0
0
3C
15ns
29
Minimum /RAS to /CAS delay (tRCD) 0
1
0
1
0
0
0
0
50
20ns
30
Minimum active to precharge time
(tRAS)
-A75B/B75B
0
0
1
0
1
1
0
1
2D
45ns
-10B
0
0
1
1
0
0
1
0
32
50ns
31
Module bank density
1
0
0
0
0
0
0
0
80
1 bank
512MB
32
Address and command setup time
before clock (tIS)
-A75B/B75B
1
0
0
1
0
0
0
0
90
0.9ns*
5
-10B
1
0
1
1
0
0
0
0
B0
1.1ns*
5
33
Address and command hold time after
clock (tIH)
-A75B/B75B
1
0
0
1
0
0
0
0
90
0.9ns*
5
-10B
1
0
1
1
0
0
0
0
B0
1.1ns*
5
34
Data input setup time before clock
(tDS)
-A75B/B75B
0
1
0
1
0
0
0
0
50
0.5ns*
5
-10B
0
1
1
0
0
0
0
0
60
0.6ns*
5
35
Data input hold time after clock (tDH)
-A75B/B75B
0
1
0
1
0
0
0
0
50
0.5ns*
5
-10B
0
1
1
0
0
0
0
0
60
0.6ns*
5
36 to 40
Superset information
0
0
0
0
0
0
0
0
00
Future use
41
Active command period (tRC)
-A75B/B75B
0
1
0
0
0
0
0
1
41
65ns*
5
-10B
0
1
0
0
0
1
1
0
46
70ns*
5
42
Auto refresh to active/
Auto refresh command cycle (tRFC)
-A75B/B75B
0
1
0
0
1
0
1
1
4B
75ns*
5
-10B
0
1
0
1
0
0
0
0
50
80ns*
5
43
SDRAM tCK cycle max. (tCK max.)
0
0
1
1
0
0
0
0
30
12ns*
5
44
Dout to DQS skew
-A75B/B75B
0
0
1
1
0
0
1
0
32
500ps*
5
-10B
0
0
1
1
1
1
0
0
3C
600ps*
5
45
Data hold skew (tQHS)
-A75B/B75B
0
1
1
1
0
1
0
1
75
750ps*
5
-10B
1
0
1
0
0
0
0
0
A0
1000ps*
5
46 to 61
Superset information
0
0
0
0
0
0
0
0
00
Future use
62
SPD revision
0
0
0
0
0
0
0
0
00
Initial
63
Checksum for bytes 0 to 62
-A75B
0
0
0
0
0
0
1
1
03
3
-B75B
0
0
1
1
0
0
1
1
33
51
-10B
1
1
1
1
1
0
0
0
F8
248
64
Manufacturer's JEDEC ID code
0
0
0
0
0
1
1
1
07
HITACHI
65 to 71
Manufacturer's JEDEC ID code
0
0
0
0
0
0
0
0
00
72
Manufacturing location
*
2
(ASCII-8bit
code)
73
Module part number
0
1
0
0
1
0
0
0
48
H
74
Module part number
0
1
0
0
0
0
1
0
42
B
75
Module part number
0
0
1
1
0
1
0
1
35
5
HB54A5129F1-A75B/B75B/10B
Data Sheet E0090H40 (Ver. 4.0)
7
Byte No.
Function described
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 Hex value
Comments
76
Module part number
0
0
1
1
0
1
0
0
34
4
77
Module part number
0
1
0
0
0
0
0
1
41
A
78
Module part number
0
0
1
1
0
1
0
1
35
5
79
Module part number
0
0
1
1
0
0
0
1
31
1
80
Module part number
0
0
1
1
0
0
1
0
32
2
81
Module part number
0
0
1
1
1
0
0
1
39
9
82
Module part number
0
1
0
0
0
1
1
0
46
F
83
Module part number
0
0
1
1
0
0
0
1
31
1
84
Module part number
0
0
1
0
1
1
0
1
2D
--
85
Module part number
-A75B
0
1
0
0
0
0
0
1
41
A
-B75B
0
1
0
0
0
0
1
0
42
B
-10B
0
0
1
1
0
0
0
1
31
1
86
Module part number
-A75B/B75B
0
0
1
1
0
1
1
1
37
7
-10B
0
0
1
1
0
0
0
0
30
0
87
Module part number
-A75B/B75B
0
0
1
1
0
1
0
1
35
5
-10B
0
1
0
0
0
0
1
0
42
B
88
Module part number
-A75B/B75B
0
1
0
0
0
0
1
0
42
B
-10B
0
0
1
0
0
0
0
0
20
(Space)
89 to 90
Module part number
0
0
1
0
0
0
0
0
20
(Space)
91
Revision code
0
0
1
1
0
0
0
0
30
Initial
92
Revision code
0
0
1
0
0
0
0
0
20
(Space)
93
Manufacturing date
Year code
(BCD)
94
Manufacturing date
Week code
(BCD)
95 to 98
Module serial number
*
3
99 to 127
Manufacturer specific data
*
4
Notes: 1. All serial PD data are not protected. 0: Serial data, "driven Low", 1: Serial data, "driven High" These
SPD are based on JEDEC Committee Ballot JC-42.5-99-129.
2. Byte72 is manufacturing location code. (ex: In case of Japan, byte72 is 4AH. 4AH shows "J" on ASCII
code.)
3. Bytes 95 through 98 are assembly serial number.
4. All bits of 99 through 127 are not defined ("1" or "0").
5. These specifications are defined based on component specification, not module.
HB54A5129F1-A75B/B75B/10B
Data Sheet E0090H40 (Ver. 4.0)
8
Block Diagram
DQ
DQS
DM
DQ0 to DQ3
4
DQS0
R
S
R
S
/CS
D0
/RS0
VSS
DQ
DQ8 to DQ11
4
DQS1
R
S
R
S
D1
DQ
DQ16 to DQ19
4
DQS2
R
S
R
S
D2
DQ
DQ24 to DQ27
4
DQS3
R
S
R
S
D3
DQ
DQ32 to DQ35
4
DQS4
R
S
R
S
D4
DQ
DQ40 to DQ43
4
DQS5
R
S
R
S
D5
DQ
DQ48 to DQ51
4
DQS6
R
S
R
S
D6
DQ
DQ56 to DQ59
4
DQS7
R
S
R
S
D7
DQ
CB0 to CB3
4
DQS8
R
S
R
S
D8
DQS
DM
/CS
DQS
DM
/CS
DQS
DM
/CS
DQS
DM
/CS
DQS
DM
/CS
DQS
DM
/CS
DQS
DM
/CS
DQS
DM
/CS
DQ
DQS
DM
DQ4 to DQ7
4
DM0/DQS9
R
S
R
S
/CS
D9
DQ
DQ12 to DQ15
4
DM1/DQS10
R
S
R
S
D10
DQ
DQ20 to DQ23
4
DM2/DQS11
R
S
R
S
D11
DQ
DQ28 to DQ31
4
DM3/DQS12
R
S
R
S
D12
DQ
DQ36 to DQ39
4
DM4/DQS13
R
S
R
S
D13
DQ
DQ44 to DQ47
4
DM5/DQS14
R
S
R
S
D14
DQ
DQ52 to DQ55
4
DM6/DQS15
R
S
R
S
D15
DQ
DQ60 to DQ63
4
DM7/DQS16
R
S
R
S
D16
DQ
CB4 to CB7
4
DM8/DQS17
R
S
R
S
D17
DQS
DM
/CS
DQS
DM
/CS
DQS
DM
/CS
DQS
DM
/CS
DQS
DM
/CS
DQS
DM
/CS
DQS
DM
/CS
DQS
DM
/CS
* D0 to D17: HM5425401
U0: 2k bits EEPROM
R
S
: 22
PLL: CDCV857
Register: SSTV16857
R
S
R
S
R
S
R
S
R
S
R
S
R
S
Serial PD
SDA
A0
A1
A2
SA0
SA1
SA2
SCL
SCL
U0
SDA
Notes:
1. The SDA pull-up resistor is required due to
the open-drain/open-collector output.
2. The SCL pull-up resistor is recommended
because of the normal SCL line inacitve
"high" state.
VCCQ
D0 to D17
D0 to D17
D0 to D17
D0 to D17
VCC
VSS
VREF
VCCID
open
/S0
BA0 to BA1
A0 to A12
/RAS
/CAS
CKE0
/WE
/RS0 -> /CS: SDRAMs D0 to D17
RBA0 to RBA1 -> BA0 to BA1: SDRAMs D0 to D17
RA0 to RA12 -> A0 to A12: SDRAMs D0 to D17
/RRAS -> /RAS: SDRAMs D0 to D17
/RCAS -> /CAS: SDRAMs D0 to D17
RCKE0A -> CKE: SDRAMs D0 to D17
/RWE -> /WE: SDRAMs D0 to D17
R
E
G
I
S
T
E
R
PCK
/PCK
CK0, /CK0
PLL*
/RESET
Note: Wire per Clock loading table/Wiring diagrams.
HB54A5129F1-A75B/B75B/10B
Data Sheet E0090H40 (Ver. 4.0)
9
Differential Clock Net Wiring (CK0, /CK0)
120
240
(Typically two registers per DIMM)
0ns (nominal)
240
120
120
CK0
Notes: 1. The clock delay from the input of the PLL clock to the input of any SDRAM or register willl
be set to 0 ns (nominal).
2. Input, output and feedback clock lines are terminated from line to line as shown, and not
from line to ground.
3. Only one PLL output is shown per output type. Any additional PLL outputs will be wired
in a similar manner.
4. Termination resistors for feedback path clocks are located after the pins of the PLL.
C
/CK0
SDRAM
stack
SDRAM
stack
Register1
Register2
PLL
Feedback
IN
OUT1
OUT'N'
HB54A5129F1-A75B/B75B/10B
Data Sheet E0090H40 (Ver. 4.0)
10
Pin Functions (1)
CK (CLK), /CK (/CLK) (input pin): The CK and the /CK are the master clock inputs. All inputs except DMs, DQSs
and DQs are referred to the cross point of the CK rising edge and the VREF level. When a read operation, DQSs
and DQs are referred to the cross point of the CK and the /CK. When a write operation, DMs and DQs are referred
to the cross point of the DQS and the VREF level. DQSs for write operation are referred to the cross point of the CK
and the /CK.
/S (/CS) (input pin): When /S is Low, commands and data can be input. When /S is High, all inputs are ignored.
However, internal operations (bank active, burst operations, etc.) are held.
/RAS, /CAS, and /WE (input pins): These pins define operating commands (read, write, etc.) depending on the
combinations of their voltage levels. See "Command operation".
A0 to A12 (input pins): Row address (AX0 to AX12) is determined by the A0 to the A12 level at the cross point of
the CK rising edge and the VREF level in a bank active command cycle. Column address (AY0 to AY9, AY11) is
loaded via the A0 to the A9, the A11 at the cross point of the CK rising edge and the VREF level in a read or a write
command cycle. This column address becomes the starting address of a burst operation.
A10 (AP) (input pin): A10 defines the precharge mode when a precharge command, a read command or a write
command is issued. If A10 = High when a precharge command is issued, all banks are precharged. If A10 = Low
when a precharge command is issued, only the bank that is selected by BA1, BA0 is precharged. If A10 = High
when read or write command, auto-precharge function is enabled. While A10 = Low, auto-precharge function is
disabled.
BA0, BA1 (input pin): BA0/BA1 are bank select signals. The memory array is divided into bank 0, bank 1, bank 2
and bank 3. If BA1 = Low and BA0 = Low, bank 0 is selected. If BA1 = High and BA0 = Low, bank 1 is selected. If
BA1 = Low and BA0 = High, bank 2 is selected. If BA1 = High and BA0 = High, bank 3 is selected.
CKE (input pin): CKE controls power down and self-refresh. The power down and the self-refresh commands are
entered when the CKE is driven Low and exited when it resumes to High.
The CKE level must be kept for 1 CK cycle (= LCKEPW) at least, that is, if CKE changes at the cross point of the CK
rising edge and the VREF level with proper setup time tIS, at the next CK rising edge CKE level must be kept with
proper hold time tIH.
Pin Functions (2)
DQ, CB (input and output pins): Data are input to and output from these pins.
DQS (input and output pin):
DQS provide the read data strobes (as output) and the write data strobes (as input).
VCC and VCCQ (power supply pins): 2.5V is applied. (VCC is for the internal circuit and VCCQ is for the output
buffer.)
VCCSPD (power supply pin): 2.5V is applied (For serial EEPROM).
VSS (power supply pin): Ground is connected.
/RESET (input pin): LVCMOS reset input. When /RESET is low, all registers are reset and all outputs are low.
Detailed Operation Part, AC Characteristics and Timing Waveforms
Refer to the HM5425161B/HM5425801B/HM5425401B Series datasheet (E0086H10). DM pins of component
device fixed to VSS level on the module board. DIMM /CAS latency = Device CL + 1 for registered type.
HB54A5129F1-A75B/B75B/10B
Data Sheet E0090H40 (Ver. 4.0)
11
Electrical Specifications
Absolute Maximum Ratings
Parameter
Symbol
Value
Unit
Note
Voltage on any pin relative to VSS
VT
1.0 to +4.6
V
1
Supply voltage relative to VSS
VCC, VCCQ
1.0 to +4.6
V
1
Short circuit output current
IOUT
50
mA
Power dissipation
PT
18
W
Operating temperature
Topr
0 to +55
C
Storage temperature
Tstg
50 to +100
C
Notes: 1. Respect to VSS.
DC Operating Conditions (TA = 0 to +55C)
Parameter
Symbol
min.
Typ
max.
Unit
Notes
Supply voltage
VCC, VCCQ
2.3
2.5
2.7
V
1, 2
VSS
0
0
0
V
Input reference voltage
VREF
1.15
1.25
1.35
V
1
Termination voltage
VTT
VREF 0.04
VREF
VREF + 0.04
V
1
DC Input high voltage
VIH
VREF + 0.18
--
VCCQ + 0.3
V
1, 3
DC Input low voltage
VIL
0.3
--
VREF 0.18
V
1, 4
DC Input signal voltage
VIN (dc)
0.3
--
VCCQ + 0.3
V
5
DC differential input voltage
VSWING (dc) 0.36
--
VCCQ + 0.6
V
6
Notes: 1. All parameters are referred to VSS, when measured.
2. VCCQ must be lower than or equal to VCC.
3. VIH is allowed to exceed VCC up to 4.6V for the period shorter than or equal to 5ns.
4. VIL is allowed to outreach below VSS down to 1.0V for the period shorter than or equal to 5ns.
5. VIN (dc) specifies the allowable dc execution of each differential input.
6. VSWING (dc) specifies the input differential voltage required for switching.
HB54A5129F1-A75B/B75B/10B
Data Sheet E0090H40 (Ver. 4.0)
12
DC Characteristics
1 (TA = 0 to 55C, VCC, VCCQ = 2.5V 0.2V, VSS = 0V)
Parameter
Symbol
Grade
max.
Unit
Test condition
Notes
Operating current (ACTV-PRE)
ICC0
-A75B
-B75B
-10B
2194
2096
1819
mA
CKE VIH, tRC = min. 1, 2, 5
Operating current (ACTV-READ-
PRE)
ICC1
-A75B
-B75B
-10B
3184
2996
2719
mA
CKE VIH, BL = 2,
CL = 3.5, tRC = min.
1, 2, 5
Idle power down standby current ICC2P
-A75B
-B75B
-10B
718
656
595
mA
CKE VIL
4
Idle standby current
ICC2N
-A75B
-B75B
-10B
1114
1016
919
mA
CKE VIH, /CS VIH 4
Active power down standby
current
ICC3P
-A75B
-B75B
-10B
844
746
649
mA
CKE VIL
3
Active standby current
ICC3N
-A75B
-B75B
-10B
1294
1196
1099
mA
CKE VIH, /CS VIH
tRAS = max.
3
Operating current
(Burst read operation)
ICC4R
-A75B
-B75B
-10B
4444
4256
4069
mA
CKE VIH, BL = 2,
CL = 3.5
1, 2, 5, 6
Operating current
(Burst write operation)
ICC4W
-A75B
-B75B
-10B
4084
3896
3709
mA
CKE VIH, BL = 2,
CL = 3.5
1, 2, 5, 6
Auto refresh current
ICC5
-A75B
-B75B
-10B
4084
3986
3619
mA
tRFC = min.,
Input VIL or VIH
Self refresh current
ICC6
-A75B
-B75B
-10B
448
440
433
mA
Input VCC 0.2V
Input 0.2V.
Notes. 1. These ICC data are measured under condition that DQ pins are not connected.
2. One bank operation.
3. One bank active.
4. All banks idle.
5. Command/Address transition once per one cycle.
6. Data/Data mask transition twice per one cycle.
7. The ICC data on this table are measured with regard to tCK = min. in general.
DC Characteristics
2 (TA = 0 to 55C, VCC, VCCQ = 2.5V 0.2V, VSS = 0V)
Parameter
Symbol
min.
max.
Unit
Test condition
Notes
Input leakage current
ILI
10
10
A
VCC VIN VSS
Output leakage current
ILO
10
10
A
VCC VOUT VSS
Output high voltage
VOH
VTT + 0.76
--
V
IOH (max.) = 15.2mA
Output low voltage
VOL
--
VTT 0.76
V
IOL (min.) = 15.2mA
HB54A5129F1-A75B/B75B/10B
Data Sheet E0090H40 (Ver. 4.0)
13
Pin Capacitance (TA = 25C, VCC, VCCQ = 2.5V 0.2V)
Parameter
Symbol
Pins
max.
Unit
Notes
Input capacitance
CI1
Address, /RAS, /CAS, /WE,
/S, CKE
10
pF
1, 3
Input capacitance
CI2
CK, /CK
20
pF
1, 3
Data and DQS input/output
capacitance
CO
DQ, DQS, CB
15
pF
1, 2, 3
Notes: 1. These parameters are measured on conditions: f = 100MHz, VOUT = VCCQ/2,
VOUT = 0.2V.
2. Dout circuits are disabled.
3. This parameter is sampled and not 100% tested.
Timing Parameter Measured in Clock Cycle for Registered DIMM
Number of clock cycle
Parameter
Symbol
min.
max.
Write to pre-charge command delay (same bank)
tWPD
3 + BL/2
Read to pre-charge command delay (same bank)
tRPD
BL/2
Write to read command delay (to input all data)
tWRD
2 + BL/2
Burst stop command to write command delay
(CL = 3)
tBSTW
2
(CL = 3.5)
tBSTW
3
Burst stop command to DQ High-Z
(CL = 3)
tBSTZ
3
(CL = 3.5)
tBSTZ
3.5
Read command to write command delay (to output all data)
(CL = 3)
tRWD
2 + BL/2
(CL = 3.5)
tRWD
3 + BL/2
Pre-charge command to High-Z
(CL = 3)
tHZP
3
(CL = 3.5)
tHZP
3.5
Write command to data in latency
tWCD
2
Write recovery
tWR
1
Register set command to active or register set command
tMRD
2
Self refresh exit to non-read command
tSNR
10
Self refresh exit to read command
tSRD
200
Power down entry
tPDEN
1
Power down exit to command input
tPDEX
1
CKE minimum pulse width
tCKEPW
1
HB54A5129F1-A75B/B75B/10B
Data Sheet E0090H40 (Ver. 4.0)
14
Physical Outline
Detail A
0.20 0.15
2.50 0.20
1.27 typ
133.35 0.15
128.95
2.30
64.77
49.53
(64.48)
A
B
1
92
93
R 2.00
184
1.00 0.05
Unit: mm
Note: Tolerance on all dimensions 0.13 unless otherwise specified.
1.27 0.10
3.00 min
4.00 min
10.00
4.00 0.10
17.80
43.18 0.15
4.00 max
2
2.50 0.10
Component area
(Front)
Component area
(Back)
(DATUM -A-)
6.35
Detail B
3.80
1.80 0.10
2.175
6.62
R 0.90
(DATUM -A-)
ECA-TS2-0059-01
HB54A5129F1-A75B/B75B/10B
Data Sheet E0090H40 (Ver. 4.0)
15
CAUTION FOR HANDLING MEMORY MODULES
When handling or inserting memory modules, be sure not to touch any components on the modules, such as
the memory ICs, chip capacitors and chip resistors. It is necessary to avoid undue mechanical stress on
these components to prevent damaging them.
In particular, do not push module cover or drop the modules in order to protect from mechanical defects,
which would be electrical defects.
When re-packing memory modules, be sure the modules are not touching each other.
Modules in contact with other modules may cause excessive mechanical stress, which may damage the
modules.
MDE0202
NOTES FOR CMOS DEVICES
1
PRECAUTION AGAINST ESD FOR MOS DEVICES
Exposing the MOS devices to a strong electric field can cause destruction of the gate
oxide and ultimately degrade the MOS devices operation. Steps must be taken to stop
generation of static electricity as much as possible, and quickly dissipate it, when once
it has occurred. Environmental control must be adequate. When it is dry, humidifier
should be used. It is recommended to avoid using insulators that easily build static
electricity. MOS devices must be stored and transported in an anti-static container,
static shielding bag or conductive material. All test and measurement tools including
work bench and floor should be grounded. The operator should be grounded using
wrist strap. MOS devices must not be touched with bare hands. Similar precautions
need to be taken for PW boards with semiconductor MOS devices on it.
2
HANDLING OF UNUSED INPUT PINS FOR CMOS DEVICES
No connection for CMOS devices input pins can be a cause of malfunction. If no
connection is provided to the input pins, it is possible that an internal input level may be
generated due to noise, etc., hence causing malfunction. CMOS devices behave
differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed
high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected
to V
DD
or GND with a resistor, if it is considered to have a possibility of being an output
pin. The unused pins must be handled in accordance with the related specifications.
3
STATUS BEFORE INITIALIZATION OF MOS DEVICES
Power-on does not necessarily define initial status of MOS devices. Production process
of MOS does not define the initial operation status of the device. Immediately after the
power source is turned ON, the MOS devices with reset function have not yet been
initialized. Hence, power-on does not guarantee output pin levels, I/O settings or
contents of registers. MOS devices are not initialized until the reset signal is received.
Reset operation must be executed immediately after power-on for MOS devices having
reset function.
CME0107
HB54A5129F1-A75B/B75B/10B
Data Sheet E0090H40 (Ver. 4.0)
16
M01E0107
No part of this document may be copied or reproduced in any form or by any means without the prior
written consent of Elpida Memory, Inc.
Elpida Memory, Inc. does not assume any liability for infringement of any intellectual property rights
(including but not limited to patents, copyrights, and circuit layout licenses) of Elpida Memory, Inc. or
third parties by or arising from the use of the products or information listed in this document. No license,
express, implied or otherwise, is granted under any patents, copyrights or other intellectual property
rights of Elpida Memory, Inc. or others.
Descriptions of circuits, software and other related information in this document are provided for
illustrative purposes in semiconductor product operation and application examples. The incorporation of
these circuits, software and information in the design of the customer's equipment shall be done under
the full responsibility of the customer. Elpida Memory, Inc. assumes no responsibility for any losses
incurred by customers or third parties arising from the use of these circuits, software and information.
[Product applications]
Elpida Memory, Inc. makes every attempt to ensure that its products are of high quality and reliability.
However, users are instructed to contact Elpida Memory's sales office before using the product in
aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment,
medical equipment for life support, or other such application in which especially high quality and
reliability is demanded or where its failure or malfunction may directly threaten human life or cause risk
of bodily injury.
[Product usage]
Design your application so that the product is used within the ranges and conditions guaranteed by
Elpida Memory, Inc., including the maximum ratings, operating supply voltage range, heat radiation
characteristics, installation conditions and other related characteristics. Elpida Memory, Inc. bears no
responsibility for failure or damage when the product is used beyond the guaranteed ranges and
conditions. Even within the guaranteed ranges and conditions, consider normally foreseeable failure
rates or failure modes in semiconductor devices and employ systemic measures such as fail-safes, so
that the equipment incorporating Elpida Memory, Inc. products does not cause bodily injury, fire or other
consequential damage due to the operation of the Elpida Memory, Inc. product.
[Usage environment]
This product is not designed to be resistant to electromagnetic waves or radiation. This product must be
used in a non-condensing environment.
If you export the products or technology described in this document that are controlled by the Foreign
Exchange and Foreign Trade Law of Japan, you must follow the necessary procedures in accordance
with the relevant laws and regulations of Japan. Also, if you export products/technology controlled by
U.S. export control regulations, or another country's export control laws or regulations, you must follow
the necessary procedures in accordance with such laws or regulations.
If these products/technology are sold, leased, or transferred to a third party, or a third party is granted
license to use these products, that third party must be made aware that they are responsible for
compliance with the relevant laws and regulations.
The information in this document is subject to change without notice. Before using this document, confirm that this is the latest version.