Microwave Ceramics and Modules
Filter
2 Pole Filter for W-LAN 5GHz / [5.7255.875] Band
B69842N5807A150
Preliminary Data Sheet
ISSUE DATE
19.03.04
ISSUE
P2
PUBLISHER
SAW MWC PD
PAGE
1/5
Features
SMD filter consisting of coupled resonators with stepped impedances
MgTiO3 - CaTiO3 (
r = 21 / TCf =010 ppm/K) with a coating of copper (10
m) and tin (>5
m)
Excellent reflow solderability, no migration effect due to copper/tin metallization
Index
Page 2
Component drawing
Recommended footprint
Page 3
Characteristics
Maximum ratings
Typical passband characteristic
Page 4
Broadband characteristic
Processing information
Soldering requirements
Page 5
Delivery mode
Microwave Ceramics and Modules
Filter
2 Pole Filter for W-LAN 5GHz / [5.7255.875] Band
B69842N5807A150
Preliminary Data Sheet
ISSUE DATE
19.03.04
ISSUE
P2
PUBLISHER
SAW MWC PD
PAGE
2/5
Component drawing
Recommended footprint
Soldered Pads.
I/O Pads must be
connected to 50 ohms
impedance lines.
ground covered with solder
resist. It must be
connected to groung plane
below by vias
Max diameter: 0.3 mm
Max via pitch:1 mm
View from below onto the solder terminals and view from beside
Microwave Ceramics and Modules
Filter
2 Pole Filter for W-LAN 5GHz / [5.7255.875] Band
B69842N5807A150
Preliminary Data Sheet
ISSUE DATE
19.03.04
ISSUE
P2
PUBLISHER
SAW MWC PD
PAGE
3/5
Characteristics
min.
typ.
max.
Center frequency
fc -
5.8
-
GHz
Insertion loss
IL
1.1
1.3
dB
Passband
B 150
MHz
Standing wave ratio
SWR
1.5
2.0
Impedance
Z
50
Power
P
1.0
W
Attenuation
at DC to 1990 MHz
at 3300 MHz
at 5000 MHz
at 5425 MHZ
at 6175 MHz
at 6800 MHz
55
40
40
12
8
25
60
46
45
15
12
27
dB
dB
dB
dB
dB
dB
Maximum ratings
IEC climatic category (IEC 68-1)
- 40/+ 90/56
Operating temperature
Top -40 / + 85
C
Typical passband characteristic
-60
-50
-40
-30
-20
-10
0
4,0
4,2
4,4
4,6
4,8
5,0
5,2
5,4
5,6
5,8
6,0
Frequency [GHz]
[dB]
S11 [dB]
S21 [dB]
Microwave Ceramics and Modules
Filter
2 Pole Filter for W-LAN 5GHz / [5.7255.875] Band
B69842N5807A150
Preliminary Data Sheet
ISSUE DATE
19.03.04
ISSUE
P2
PUBLISHER
SAW MWC PD
PAGE
4/5
Broadband characteristic
Epcos B69842N5777A100 upperharmonics
-60
-50
-40
-30
-20
-10
0
1,0
2,0
3,0
4,0
5,0
6,0
7,0
8,0
9,0
10,0
11,0
12,0
13,0
14,0
15,0
16,0
17,0
18,0
19,0
20,0
21,0
freq [GHz]
Att [dB]
S21[dB]
Processing information
Wettability acc. to IEC 68-2-58:
75% (after aging)
Soldering requirements
Profile for eutectic
SnPb solder paste
Profile for leadfree
solder paste
Soldering type
reflow
reflow
Maximum soldering temperature
235 (max. 2 sec.)
260 (max. 2 sec.)
C
(measuring point on top surface of the component) 225 (max. 10 sec.)
250 (max. 10 sec.) C
Recommended soldering conditions (infrared):
20-40 sec.
40-80 sec.
within 10 sec.
Time [sec.]
Temp. [C]
215C10C
30 sec.
2-3 min.
within 10 sec.
Time [sec.]
Temp. [C]
245C5C
2.5 C/s
> - 5 C/s
Microwave Ceramics and Modules
Filter
2 Pole Filter for W-LAN 5GHz / [5.7255.875] Band
B69842N5807A150
Preliminary Data Sheet
ISSUE DATE
19.03.04
ISSUE
P2
PUBLISHER
SAW MWC PD
PAGE
5/5
Delivery mode
Blister tape acc. to IEC 286-3, PS, grey
Pieces/tape: 4000
EPCOS AG 2001. All Rights Reserved. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
The information contained in this data sheet describes the type of component and shall not be considered as guaranteed characteristics.
Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry
recommended by the ZVEI (German Electrical and Electronic Manufacturers' Association), unless otherwise agreed.
PDF 
ZIP