APD Receiver Module
up to 3 Gb/s
PGR 203 12
Description
Fiber optic receiver front-end module for STM-16 and OC-48 WDM applica-
tions. The module includes an InGaAs Avalanche Photo Diode (APD), with a
low noise GaAs MMIC preamplifier in a 14 pin butterfly package.The module
is equipped with an internal thermistor. The single-mode fiber pigtail is
terminated with a customer specified connector. The module operates
between 1250 and 1620 nm. The electrical outputs are AC-coupled and
differential.
Key Features
Hermetic, 14 pin butterfly package with
multisourced footprint
FC/PC, SC or ST connector
InGaAs APD with low noise GaAs
MMIC preamplifier
AC-coupled, differential data output
Operates between 1250 nm and
1620 nm
2.0 GHz minimum bandwidth
-34 dBm typical sensitivity
-3 dBm typical overload
Applications
WDM
SDH STM-16 LH
SONET OC-48 LR
Digital recievers to 3 Gb/s
Analog receivers to 2.0 GHz
1
PGR 203 12
2
Pin connection
1.
GND
2.
Vapd (+HV)
3.
GND
4.
Vss (-5.2V)
5.
GND
6.
Thermistor
7.
GND
8.
GND
FIBER
DATA
APD
PREAMP
DATA_NOT
Figure 1. Block diagram
Figure 2. Pin description
9.
GND
10.
Data Out (AC-coupled)
11.
Data_Not Out (AC-coupled)
12.
GND
13.
Vdd (+5V)
14.
NC
Case RF (and DC) GND
A
25.4
12.7
20.2
17.9
12.7
3.9
4.5
4x M3 depth min 2.54
2.5
2.6
2.54
Lead 1
Lead 14
19.2
+0
-0.55
8
20.5
0.3
2.7
A
0.25
1.3
1.1
2
- 8
PGR 203 12
3
Optical and Electrical AC Characteristics
Electrical and optical characteristics over recommended operating conditions, unless otherwise noted.
Parameters are met by an individual differential output.
Parameter
Conditions
Symbol
Min
Typ
Max
Unit
Minimum bandwidth (-3dB)
-30dBm < Pf < -6dBm
BW
min
2.0
2.5
GHz
Bandwidth variation
-30dBm < Pf < -6dBm
1.2
1.3
BW
max
=
BW
min
Gain peaking
Peak
0
2
dB
Sensitivity: Pf @ BER = 110
-10
2.5 Gbps NRZ,
Pr
-34
-32
dBm
PRBS 2
23
-1,
=1550 nm
Overload: Pf @ BER = 110
-10
2.5 Gbps NRZ,
Pol
-6
-3
dBm
PRBS 2
23
-1,
=1550 nm
Output signal swing
-30dBm < Pf < -6dBm
V
Out
30
800
mV
P-P
R
L
= 50
,
= 1550nm, ER ~10
AC transimpedance
R
L
= 50
, Tz = dV
Out
/l
Ph
, ave
Tz
3.0
k
Logic sense
Data Out
Light "ON" = Logic "LOW"
Data_Not Out
Light "ON" = Logic "HIGH"
Optical and Electrical DC Characteristics
Electrical and optical characteristics over recommended operating conditions, unless otherwise noted.
Parameters are met by an individual differential output.
Parameter
Conditions
Symbol
Min
Typ
Max
Unit
DC Power supply current
I
dd
110
140
mA
I
ss
55
70
mA
Power consumption
P
Con
0.8
1.1
W
APD Responsivity
= 1300 nm, M = 12
R
13(12)
10.5
A/W
= 1550 nm, M = 12
R
15(12)
11.5
A/W
Thermistor, NTC
T = 25
C
R
Th(25)
2925
3000
3075
Optical reflectance
s11
-27
dB
Recommended Operating Conditions
Parameter
Symbol
Min
Typ
Max
Unit
Optical wavelength
1250
1620
nm
Case temperature
T
Case
0
70
C
DC Power supply voltage
V
dd
4.7
5.0
5.3
V
V
ss
-5.5
-5.2
-4.9
V
APD bias
V
Apd
30
85
V
Absolute Maximum Ratings
Parameter
Symbol
Min
Max
Unit
DC Power supply voltage
V
dd
-0.5
6.5
V
V
ss
-7.0
0.5
V
Storage temperature
T
Stg
-40
85
C
CAUTION: Stresses outside those listed in "Absolute Maximum Ratings" may cause permanent damage to the device.
This is a stress only rating and operation of the device at these or any other conditions above those indicated in the
operational sections of this specification is not implied.
PGR 203 12
4
Ericsson Microelectronics AB
SE-164 81 Kista, Sweden
Telephone: +46 8 757 50 00
www.ericsson.com/microelectronics
For local sales contacts, please refer to our website
or call: Int + 46 8 757 47 00, Fax: +46 8 757 47 76
1522-PGR 203 12 Rev. B
Ericsson Microelectronics AB, August 2000
Information given in this data sheet is believed to be accurate and
reliable. However no responsibility is assumed for the consequences of
its use nor for any infringement of patents or other rights of third
parties which may result from its use. No license is granted by
implication or otherwise under any patent or patent rights of Ericsson
Microelectronics. These products are sold only according to Ericsson
Microelectronics' general conditions of sale, unless otherwise
confirmed in writing.
Product specifications subject to change without
notice.
Handling Precautions
This device may be damaged as a result of electrostatic
discharge (ESD). Take proper precautions during both han-
dling and testing. This typically includes grounded wrist
wraps, workbenches and floor mats in ESD controlled areas.
Semiconductor devices may be damaged by current surges,
use appropriate transient protection.
Quality Assurance
Ericsson Microelectronics commitment to quality has been
proven through a decade of semiconductor device produc-
tion and has been confirmed to ISO 9001. Opto product
qualification is made according to the intention of applicable
Telcordia standards.
Connector Options
FC/PC
SC
ST
(Other connectors available on request)
PDF 
ZIP