Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: info@actcrystals.com
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered - Registration number 6830/2
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
1 OF 3
This specification covers the characteristics of SAW Filter ACTF474/374.0/QCC8C,
in a QCC8C package and is designed for use in wireless LAN applications.
1.Package Dimension (QCC8C)
3. Matching Network (50
unbalanced)
Pins
Configuration
2
Input Ground
3
Input
6
Output Ground
7
Output
1,5
To be Grounded
4,8
Case Ground
Sign
Data (unit: mm)
Sign
Data (unit: mm)
A
2.08
E
1.20
B
0.60
F
1.35
C
1.27
G
5.00
D
2.54
H
5.00
Issue : 1 C1
Date : SEPT 04
Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: info@actcrystals.com
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered - Registration number 6830/2
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
2 OF 3
4.Typical Frequency Response
5.Performance
5-1. Maximum Ratings
Rating
Value
Units
Source Power P
S
10
dBm
DC Voltage V
DC
0
V
Storage Temperature
-40 to +85
C
Soldering Temperature
+235
C
Issue : 1 C1
Date : SEPT 04
Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: info@actcrystals.com
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered - Registration number 6830/2
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
3 OF 3
5-2. Electronic Characteristics
Operating temperature: T
A
= -10 ... +80
C
Terminating source impedance: Z
S
= 50
unbalanced and matching network
Terminating load impedance: Z
L
= 50
unbalanced and matching network
Characteristics
Minimum
Typical
Maximum Units
Centre Frequency f
C
--
374.000
--
MHz
Minimum insertion attenuation
min
(including matching network)
--
9.0
10.5
dB
Bandwidth
rel
3 dB BW
3dB
17
22
--
MHz
Amplitude ripple (p-p) f
C
7MHz
--
0.5
1.0
dB
Group delay ripple (p-p) f
C
7MHz
--
40
100
ns
Triple transit suppression
30
40
--
dB
Relative attenuation (relative to
min
)
rel
357.5 ~ 352.0 MHz
352.0 ~ 341.0 MHz
341.0 ~ 224.0 MHz
390.5 ~ 392.0 MHz
392.0 ~ 396.0 MHz
396.0 ~ 422.0 MHz
422.0 ~ 454.0 MHz
30
40
48
20
30
38
40
42
45
52
38
42
44
45
--
--
--
--
--
--
--
dB
dB
dB
dB
dB
dB
dB
Temperature coefficient of frequency T
Cf
--
-87
--
ppm/K
i
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling
!
1. The frequency f
C
is defined as the midpoint between the 3dB frequencies.
2. Unless noted otherwise, all measurements are made with the filter installed in the specified test fixture that is
connected to a
50
test system with VSWR
1.2:1. The test fixture L and C are adjusted for minimum
insertion loss at the filter centre frequency, f
C
. Note that insertion loss, bandwidth, and passband shape are
dependent on the impedance matching component values and quality.
3. Unless noted otherwise, specifications apply over the entire specified operating temperature range.
4. The specifications of this device are based on the test circuit shown above and subject to change or
obsolescence without notice.
5. All equipment designs utilizing this product must be approved by the appropriate government agency prior to
manufacture or sale.
6.
Our liability is only assumed for the Surface Acoustic Wave (SAW) component(s) per se, not for applications,
processes and circuits implemented within components or assemblies.
Issue : 1 C1
Date : SEPT 04