357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Email:
nelsales@nelfc.com
www.nelfc.com
CMOS Compatible Enable/Disable
HA-A1370/A1380 Series
Description
The HA-A1370 Series of quartz crystal oscillators provide enable/disable 3-state CMOS compatible signals
for bus connected systems. Supplying Pin 1 of the HA-A1370 units with a logic "0" enables the output on
Pin 5. Alternately, supplying pin 1 of the HA-A1380 units with a logic "1" enables its Pin 5 output. In the
disabled mode, Pin 5 presents a high impedance to the load. All units are resistance welded in an all metal
package, offering RFI shielding, and are designed to survive standard wave soldering operations without
damage. Insulated standoffs to enhance board cleaning are standard.
Features
Wide frequency range 0.5MHz to 20.0MHz
User specified tolerance available
Will withstand vapor phase temperatures of 253C
for 4 minutes maximum
Space-saving alternative to discrete component
oscillators
High shock resistance, to 3000g
All metal, resistance weld, hermetically sealed
package
3.3 Volt operation
Low Jitter
High Q Crystal actively tuned oscillator circuit
Power supply decoupling internal
No internal PLL avoids cascading PLL problems
Low power consumption
Gold plated leads - Solder dipped leads available
upon request
Electrical Connection
Pin Connection
1 Enable Input
4 Grd & Case
5 Output
8 V
DD
Dimensions are in inches and (MM)
CRYSTAL CLOCK OSCILLATORS
Data Sheet 0016J
Rev. E
357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Email:
nelsales@nelfc.com
www.nelfc.com
HA-A1370/A1380 Series Continued
CMOS Compatible - Enable/Disable
Operating Conditions and Output Characteristics
Electrical Characteristics
Parameter
Symbol
Conditions
Min
Typical
Max
Frequency
-----
-----
0.5MHz
-----
20.0MHz
Duty Cycle -----
@ V
DD
/2
40/60% -----
60/40%
Logic 0
V
OL
@ 600A -----
-----
0.2V
Logic 1
V
OH
@ 600A
V
DD
-0.2V
-----
-----
Rise & Fall Time
tr,tf
10-90%
----- -----
5 ns
Tpz
-----
-----
-----
-----
25 ns
Enable/Disable
Logic High Voltage
-----
-----
3.0V
2.5V
-----
Enable/Disable
Logic Low Voltage
-----
-----
-----
-----
0.4V
Jitter, RMS
(2)
-----
-----
-----
-----
8 psec
Frequency Stability
(1)
dF/F
Overall conditions including:
-100ppm
-----
+100ppm
voltage, calibration, temp.,
10 yr aging, shock, vibration
General Characteristics
Parameter
Symbol
Conditions
Min
Typical
Max
Supply Voltage
V
DD
-----
2.97V 3.3V
3.63V
Supply Current
I
DD
No Load
0.0 mA
-----
40 mA
Output current
I
O
-----
0.0 mA -----
16.0 mA
Operating temperature
T
A
-----
0C -----
70C
Storage temperature
T
S
----- -55C -----
125C
Power Dissipation
P
D
-----
-----
-----
145 mW
Lead temperature
T
L
Soldering, 10 sec. ----- -----
300C
Load
----
-----
-----
-----
15pf
Start-up time
t
S
-----
-----
2 ms
10 ms
Environmental and Mechanical Characteristics
Mechanical Shock
Per MIL-STD-202, Method 213, Condition E
Thermal Shock
Per MIL-STD-833, Method 1011, Condition A
Vibration
0.060" double amplitude 10 Hz to 55 Hz, 35g's 55Hz to 2000 Hz
Soldering Condition
300C for 10 seconds
Hermetic Seal
Leak rate less than 1 x 10
-8
atm.cc/sec of helium
Footnotes:
1) Standard frequency stability (20,25,50ppm & others available)
2) Jitter performance is frequency dependent. Please contact factory for full characterization.
Test Load:
Rev. E
CRYSTAL CLOCK OSCILLATORS
HA - A137X - FREQ
Package Code
Tolerance/Performance
HA Leaded 4 pin (8 pin)
0 100ppm 0-70C
SA Leaded 4 pin (8 pin) SMD
1 50ppm 0-70C
Gull Wing
7 25ppm 0-70C
Input Voltage
9 Customer Specific
Code Specification
A 20ppm 0-70C
A 3.3V
B 50ppm -40 to +85C
5V
C 100ppm -40 to +85C
Creating a Part Number
Data Sheet 0016J
PDF 
ZIP