EXAR Corporation, 48720 Kato Road, Fremont, CA 94538

(510) 668-7000

FAX (510) 668-7017

www.exar.com

XRD9825

16-Bit Linear CIS/CCD Sensor

Signal Processor with Serial Control

May 2000-3

FEATURES

16-Bit Resolution

One-channel 12MSPS Pixel Rate

Triple-channel 4MSPS Pixel Rate

6-Bit Programmable Gain Amplifier

8-Bit Programmable Offset Adjustment

CIS or CCD Compatibility

Internal Clamp for CIS or CCD AC Coupled
Configurations

No Missing Codes at 10MHz ADC Clock

3.3V or 5V Operation & I/O Compatibility

Serial Load Control Registers

Low Power CMOS: 200mW-typ

Low Cost 20-Lead Packages

USB Compliant

APPLICATIONS

Color and Grayscale Flatbed Scanners

Color and Grayscale Sheetfed Scanners

Multifunction Peripherals

Digital Color Copiers

General Purpose CIS or CCD Imaging

Low Cost Data Acquisition

Simple and Direct Interface to Canon 600 DPI
Sensors

GENERAL DESCRIPTION

The XRD9825 is a complete linear CIS or CCD sensor
signal processor on a single monolithic chip. The
XRD9825 includes a high speed 16-bit resolution ADC,
a 6-bit Programmable Gain Amplifier with gain adjust-
ment of 1 to 10, and 8-bit programmable input referred
offset calibration range of 800mV.

In the CCD configuration the input signal is AC coupled
with an external capacitor. An internal clamp sets the
black level. In the CIS configuration, the clamp switch
can be disabled and the CIS output signal is DC
coupled from the CIS sensor to the XRD9825. The CIS

signal is level shifted to VRB in order to use the full
range of the ADC. In the CIS configuration the input can
also be AC coupled similar to the CCD configuration.
This enables CIS signals with large black levels to be
internally clamped to a DC reference equal to the black
level. The DC reference is internally subtracted from
the input signal.

The CIS configuration can also be used in other
applications that do not require CDS function, such as
low cost data acquisition.

Rev. 1.00

ORDERING INFORMATION

Package Type

Temperature Range

Part Number

20-Lead SOIC

0°C to +70°C

XRD9825ACD

20-Lead SSOP

0°C to +70°C

XRD9825ACU

XRD9825

Rev. 1.00

AVDD

VREF+

XRD9825ACD

RED

GRN

BLU

VDCEXT

AGND

DVDD

DB0

DB1

DB2

DB4

DGND

ADCCLK

DB3

DB5/SCLK

DB6/SDATA

DB7/LD

CLAMP

SYNCH

20-Lead SOIC

PIN DESCRIPTION

Pin #

Symbol

Description

DVDD

Digital VDD (for Output Drivers)

DB0

Data Output Bit 0

DB1

Data Output Bit 1

DB2

Data Output Bit 2

DB3

Data Output Bit 3

DB4

Data Output Bit 4

DB5/SCLK

Data Output Bit 5 & Data Input SCLK

DB6/SDATA

Data Output Bit 6 & Data Input SDATA

DB7/LD

Data Output Bit 7 & LD

DGND

Digital Ground (for Output Drivers)

ADCCLK

A/D Converter Clock

CLAMP

Clamp and Video Sample Clock

SYNCH

Start of New Line and Serial Data Input Control

AGND

Analog Ground

VREF+

A/D Positive Reference for Decoupling Cap

VDCEXT

External DC Reference

BLU

Blue Input

GRN

Green Input

RED

Red Input

AVDD

Analog Power Supply

PIN CONFIGURATION

XRD9825

Rev. 1.00

ELECTRICAL CHARACTERISTICS
Test Conditions: AV

=DV

=5V, ADCCLK=12MHz, 50% Duty Cycle, T

=25°C unless otherwise specified.

Symbol

Parameter

Min.

Typ.

Max.

Unit

Conditions

Power Supplies

Analog Power Supply

3.0

3.3

5.5

(Note 2)

Digital I/O Power Supply

3.0

3.3

5.5

< AV

Supply Current

=5V

IDD

Power Down Power Supply Current

=5V

ADC Specifications

RES

Resolution

Bits

Maximum Sampling Rate

MSPS

DNL

Differential Non-Linearity

-0.7, +1.5

LSB

ADCCLK = 10MHz

-0.8, +2.0

ADCCLK = 12MHz

Bottom Reference Voltage

/10

REF

Differential Reference Voltage

0.3

0.67AV

- V

)

Ladder Resistance

300

600

780

PGA & Offset DAC Specifications

PGARES

PGA Resolution

Bits

PGAG

MIN

Minimum Gain

0.950

1.0

1.050

V/V

PGAG

MAX

Maximum Gain

9.5

10.0

10.50

V/V

PGAGD

Gain Adjustment Step Size

0.14

V/V

BLACK

Black Level Input Range

-100

500

DC Configuration

DACRES

Offset DAC Resolution

Bits

OFF

MIN

Minimum Offset Adjustment

-250

-200

-150

Mode 111, D5=0 (Note 1)

OFF

MAX

Maximum Offset Adjustment

+500

+600

+700

Mode 111, D5=0

OFF

MIN

Minimum Offset Adjustment

-450

-400

-350

Mode 111, D5=1 (Note 1)

OFF

MAX

Maximum Offset Adjustment

+350

+400

+450

Mode 111, D5=1

OFF

Offset Adjustment Step Size

3.125

Note 1:

The additional ±100 mV of adjustment with respect to the black level input range is needed to compensate
for any additional offset introduced by the XRD9825 Buffer/PGA internally.

Note 2:

It is not recommended to operate the part between 3.6V and 4.4V.

XRD9825

Rev. 1.00

ELECTRICAL CHARACTERISTICS (CONT'D)
Test Conditions: AV

=DV

=5V, ADCCLK=12MHz, 50% Duty Cycle, T

=25°C unless otherwise specified.

Symbol

Parameter

Min.

Typ.

Max.

Unit

Conditions

Buffer Specifications

Input Leakage Current

100

CIN

Input Capacitance

VIN

AC Input Voltage Range

-1.4

CIS AC; INT V

DCREF

Config Reg

=> XXX010XX

Gain=1 (Note 1)

AC Input Voltage Range

REF

CCD AC; INT V

DCREF

Config Reg

=> XXX011XX

Gain=1 (Note 1)

VIN

DC Input Voltage Range

-0.1

-1.4

CIS DC; INT V

DCREF

Config Reg

=> XXX000XX

Gain=1 (Note 2)

DC Input Voltage Range

DCEXT

-0.1

DCEXT

CIS DC; EXT V

DCREF

REF

Config Reg

=> XXX100XX

Gain=1 (Note 3)

DCEXT

+DV

REF

< AV

DCEXT

External DC Reference

0.3

CIS DC; EXT V

DCREF

Config Reg

=> XXX100XX

VIN

Input Bandwidth (small signal)

MHz

VIN

Channel to Channel Crosstalk

-60

-50

=3MHz

Internal Clamp Specifications

CLAMP

Clamp Voltage

AGND

CIS (AC) Config

3.5

CCD (AC) Config

INT

Clamp Switch On Resistance

100

150

OFF

Clamp Switch Off Resistance

Note 1: VIN

is the signal swing before the external capacitor tied to the MUX inputs.

Note 2: The -0.1V minimum is specified in order to accommodate black level signals lower than the external DC

reference (clamp) voltage.

Note 3: The V

DCEXT

-0.1V minimum is specified in order to accommodate black level signals lower than the external DC

reference voltage.

XRD9825

Rev. 1.00

ELECTRICAL CHARACTERISTICS (CONT'D)

Test Conditions: AV

=DV

= 5V, ADCCLK=6MHz, 50% Duty Cycle, T

=25°C unless otherwise specified.

Symbol

Parameter

Min.

Typ.

Max.

Unit

Conditions

System Specifications (MUX + Buffer + PGA + ADC)

Note 1

SYS

DNL

System DNL

-1.0

±0.5

+2.3

LSB

SYS

LIN

System Linearity

±6.0

LSB

SYS

System Gain Error

-5.0

+5.0

IRN

Input Referred Noise

1.5

rms

Gain=1

Input Referred Noise

0.5

rms

Gain=10

System Timing Specifications

tcklw

ADCCLK Low Pulse Width

tckhw

ADCCLK High Pulse Width

tckpd

ADCCLK Period

120

166

tsypw

SYNCH Pulse Width

trars

Rising ADCCLK to rising

SYNCH must rise equal to

SYNCH

or after ADCCLK, See Figure 18

tclpw

CLAMP Pulse Width

Note 2

Write Timing Specifications

tsclkw

SCLK Pulse Width

tdz

LD Low to SCLK High

tds

Input Data Set-up Time

tdh

Input Data Hold Time

tdl

SCLK High to LD High

ADC Digital Output Specifications

tap

Aperture Delay

tdv

Output Data Valid

tsa

SYNCH to ADCCLK

3ch Pixel Md

tlat

Latency

cycles

Config 00, 11

tlat

Latency

pixels

Config 01, 10

Digital Input Specifications

Input High Voltage

-2.5

Input Low Voltage

High Voltage Input Current

Low Voltage Input Current

Input Capacitance

Note 1:

System performance is specified for typical digital system timing specifications.

Note 2:

The actual minimum `tclpw' is dependent on the external capacitor value, the CIS output impedance.
During `clamp' operation, sufficient time needs to be allowed for the external capacitor to charge up to the
correct operating level. Refer to the description in Theory of Operation, CIS Config.

XRD9825

Rev. 1.00

THEORY OF OPERATION

CIS Configuration (Contact Image Sensor)

The XRD9825 has two configurations for CIS applica-
tions. Each configuration is set by the control registers
accessed through the serial port.

Mode 1. DC Coupled

If the CIS does not have leading or trailing black pixels
as shown in Figure 2, then DC couple the CIS output to
the XRD9825 input.

Optically Shielded

Pixels

Valid Pixels

Figure 2. Typical Output CIS Mode

Adjust the offset of the CIS (-100 mV to 500 mV) by
setting the internal registers of the XRD9825 to set the
black pixel value when the LEDs of the CIS are off.
When the LEDs are on, use the XRD9825 Program-

mable Gain to maximize the ADCs dynamic range.
Figure 3, shows a typical application for a CIS with an
offset of -100mV to 500mV.

XRD9825

Rev. 1.00

The input is added to VRB before the signal passes
through the ADC. If the CIS output is zero, then the
output of the ADC will be zero code. This enables the
CIS to be referenced to the bottom ladder reference
voltage to use the full range of the ADC.

Some CIS sensors have an output with an offset voltage
of greater than 500mV. If the CIS output is beyond the

Figure 3. Application with Offset in the Range (-100mv to 500mv)

VRT

VRB

VDD

RED

XRD9825

N/C

offset range of the XRD9825 (see Offset Control DAC,
Pg. 22) set the internal mode registers to external
reference. An external reference voltage equal to the
value of the CIS offset voltage can be applied to
VDCEXT (Figure 4) in order to meet the dynamic range
of the XRD9825. Figure 4, is a diagram of the XRD9825
in the external reference mode for CIS, DC coupled
applications.

XRD9825

Rev. 1.00

Figure 7. CIS AC Coupled Application

Mode 2. AC Coupled

If the CIS signal has a black reference for the video
signal, an external capacitor C

EXT

is used. When

CLAMP (clamp) pin is set high an internal switch allows
one side of the external capacitor to be set to ground.
It then is level shifted to correspond to the bottom ladder
reference voltage of the ADC (Figure 7).

This value corresponds to the black reference of the
image sensor. When the CLAMP pin is set back to low,
the ADC samples the video signal with respect to the
black reference. The typical value for the external

VRT

VRB

VDD

XRD9825

CLAMP

RINT

RED

U
X

REXT CEXT

N/C

capacitor is 100pF. This value should be adjusted
according to the time constant (Tc) needed in a particu-
lar application. The CLAMP pin has an internal 150 ohm
impedance (R

INT

) which is in series with the external

capacitor (C

EXT

Therefore, Tc =1/R

INT

EXT

If the input to the external capacitor has a source
impedance (R

EXT

), then:

=1/(R

INT

EXT

XRD9825

Rev. 1.00

CIS Mode Timing -- AC Coupled

(CLAMP enabled)

ADCCLK

tckhw

tcklw

tckpd

tap

Pixel N-1

Pixel N

tdv

Pixel N+1

CIS

tdv

[5:0]

[11:6]

N-8

LSB

N-7

LSB

N-6

LSB

N-5

LSB

CLAMP

tclpw

MSB

Figure 9. Timing Diagram for Figure 8

ADCCLK

Events

ADC Sample & PGA Start Track of next Pixel

MSB Data Out (8 Upper Bits)

LSB Data Out (8 Lower Bits)

ADC Track PGA Output

ADC Hold/Convert

Table 3.

CLAMP

Events

PGA Tracks V

CLAMP

& C

EXT

is Charged to

BLACK

- V

CLAMP

, which is equal to V

BLACK

PGA Tracks VIN

Table 4.

Note: There is an 8 clock latency for the output

XRD9825

Rev. 1.00

Internal CIS Reference Circuit (DB 4 = 1)

The XRD9825 has an internal register reserved for
interfacing to the Canon CIS model number CVA-
60216K. When this register is selected, the VDCEXT
(Pin 16) becomes an output voltage of 1.24 volts. This
voltage can be directly connected to the VREF (Pin 5)
of the Canon sensor. This reduces the amount of

Figure 10. Typical Application Circuitry Internal CIS Reference Circuit Mode

CANON CIS Sensor, Model #CVA=60216k

AGND

DVDD (3V - 5V)

VCC (5V)

AVDD

DGND

AGND

DGND

DVDD (3V - 5V)

ASIC

DIGITAL

N/C

CANON CIS

SENSOR

0.1uF

0.01uF

0.1uF

0.01uF

0.1uF

XRD9825

DVDD

DB0

DB1

DB2

DB3

DB4

DB5/SCLK

DB6/SDATA

DB7/LD

DGND

ADCCLK

CLAMP

SYNCH

AGND

VREF+

VDCEXT

BLU

GRN

RED

AVDD

CVA-60216K

VOUT

MODE

AGND

VCC

VREF

CLK

LED COM

LED BLU

LED GRN

LED RED

FGND

10K

47uF

NPN

0.01uF

100uF

components needed for biasing the Canon CIS sensor
(the external diodes and resistors typically used in this
application have been included inside the XRD9825 for
this mode of operation). Below is a typical application
circuit using the XRD9825 and the Canon CVA-60216K
CIS sensor.

XRD9825

Rev. 1.00

Figure 11. Typical Application Circuitry Internal CIS Rotating Gain

and Offset Line-By-Line

AVDD

AGND

DGND

VCC (5V - 15V)

DVDD (3V - 5V)

ASIC

DIGITAL

N/C

0.01u

0.1u

XRD9825

DVDD

DB0

DB1

DB2

DB3

DB4

DB5/SCLK

DB6/SDATA

DB7/LD

DGND

ADCCLK

CLAM

SYNCH

AGND

VREF+

VDCEXT

BLU

GRN

RED

AVDD

0.01u

CIS Line-By-Line Rotating Gain and Offset
(Configuration DB1 = 1, DB0 = 1)

Line-by-line rotating gain and offset minimizes the
amount of write cycles per scan. Pre-loaded values of
gain and offset can be loaded for each color before the
first line is scanned. Each gain and offset is cycled

through line-by-line so that the gain and offset do not
have to be loaded in between lines. Below is the typical
application circuit and timing for this configuration.

XRD9825

Rev. 1.00

Figure 12. Timing Diagram for Figure 11

CCD Configuration (Charge Coupled Device)

Mode 1. AC Coupled

In the CCD configuration of operation, an external
capacitor needs to be chosen according to the equa-
tions below. The typical value for the external capacitor
is 100pF. This value should be adjusted according to
the time constant (Tc) needed in a particular applica-
tion. The CLAMP pin has an internal 150 ohm imped-
ance (R

INT

) which is in series with the external capacitor

EXT

Therefore, Tc =1/R

INT

EXT

If the input to the external capacitor has a load imped-
ance (R

EXT

), then

=1/(R

INT

EXT

When CLAMP (clamp) pin is set high an internal switch
allows one side of the external capacitor to be set to
VRT (Figure 13). This value corresponds to the black
reference of the CCD. When the CLAMP pin is set back
to low, the ADC samples the video signal with respect
to the black reference. The difference between the
black reference and the video signal is the actual pixel
value of the video content. Since this value is refer-
enced to the top ladder reference voltage of the ADC a
zero input signal would yield a full scale output code.
Therefore, the output of the conversion is inverted
(internally) to correspond to zero scale output code.

CIS Rotating Gain and Offset

Line-By-Line (Md 11)

ADCCLK

CIS

SYNCH

GAIN/

OFFSET

Red Pixel Line Scan

Grn Pixel Line Scan

Blu Pixel Line Scan

Red Gain/Offset Cycle

Grn Gain/Offset Cycle

Blu Gain/Offset Cycle

Reset Internal Mux Color to Red Channel (LD = 110YYYYYY11)

tsa

tsypw

Note: Y = Previous State

Tri-State (SYNCH = LO)

XRD9825

Rev. 1.00

Area or Linear CCD Applications

Figure 13 is a block diagram for applications with Area
or Linear CCDs (The timing for Area CCDs and B/W
CCDs is the same). For Area or Linear CCD applica-
tions, a global offset is loaded into the serial port at the
beginning of a line. The gain is set to adjust for the
highest color intensity of the CCD output. Once the

pixel values have been sampled, the gain and offset are
adjusted at the beginning of the next line. For example,
if there is a line-to-line variation between the black
reference pixels, the offset is adjusted. The gain is
always adjusted for the highest color intensity.

Figure 13. CCD AC Coupled Application

VRT

VRB

VDD

RED

XRD9825

CLAMP

AREA

LINEAR

CCD

N/C

XRD9825

Rev. 1.00

tdv

AREA, LINEAR or B/W CCD -- AC Coupled

(CLAMP Enabled)

Pixel N-1

Pixel N

Pixel N+1

CCD

Channel N

ADCCLK

tckpd

tap

tckhw

tcklw

CLAMP

tclpw

N-8

MSB

N-8

LSB

N-7

MSB

N-7

LSB

N-6

MSB

N-6

LSB

[5:0]

[11:6]

Figure 15. Timing Diagram for Figure 14

Triple Channel CCD Application

Figure 6 is a block diagram for pixel-by-pixel applica-
tions with triple channel CCDs. During the optically
shielded section of a pixel, CLAMP must go high to
store the black reference on each capacitor to the input.

The gain and offset is automatically rotated to adjust for
each channel input. The MSBs (8 upper bits) are
available on the output bus on the falling edge of
ADCCLK. The LSBs (8 lower bits) are available on the
rising edge of ADCCLK.

Note: There is an 8 clock latency at the output.

XRD9825

Rev. 1.00

ADCCLK

Events

3rd

Simultaneous RED/GRN/BLU Sample Every 3rd CLK.

Convert RED, S/H GRN, S/H BLU.

All

MSB Data Out (8 upper bits)

LSB Data Out (8 lower bits)

ADC Track PGA Output

ADC Hold/Convert

CLAMP

Events

Internal Clamp Enabled

Internal RED/GRN/BLU Tracking Enabled

SYNCH

Events

Reset Internal Mux to Red, Output Bus is Tri-stated

Increment Mux Color on Falling Edge of ADCCLK

Table 5.

Figure 18. Timing Diagram for Figure 17

Note: There is an 8 clock latency at the output.

(CLAMP Enabled)

BLU

GRN

RED

ADCCLK

CLAMP

DATA

PIXEL-BY-PIXEL 3 CHANNEL CCD -- AC Coupled

tdv

RED (N-6)

MSB

N+1 Pixel

CONVERT

RED (N)

CONVERT

GRN (N)

CONVERT

BLU (N)

TRACK

RED (N)

TRACK

GRN (N)

TRACK

RED (N+1)

TRACK

BLU (N)

CONVERT
RED (N+1)

tdv

RED (N-6)

LSB

GRN (N-6)

MSB

GRN (N-6)

LSB

BLU (N-6)

MSB

BLU (N-6)

LSB

CLAMP

tsa

SYNCH

tsypw

tclp=10ns

tap

tclp=10ns

N+1 Pixel

N Pixel

Simultaneous

Sample

trars

XRD9825

Rev. 1.00

T/H

From CCD RED

Channel

From CCD

GRN Channel

From CCD BLU

Channel

12-Bit ADC

S1 S2 S3

ADCCLK

CLAMP

S4 and S5 open
at this falling
edge

S6 opens, S7
closes at this
rising edge

S7 opens, S8
closes at this
rising edge

S8 Opens, S4,
S5 and S6
close at this
rising edge

Track
GRN

Track
BLU

Track
RED

Convert

RED

Convert

RED

Convert

GRN

Convert

BLU

CCD
Waveform

S8 Opens, S4,
S5 and S6
close at this
rising edge

S9 closes at rising edge and opens
at falling edge of ADCCLK

S1, S2 and S3 close when
CLAMP is high and open
when CLAMP is low

PGA

C EXT R

C EXTG

C EXT B

VCDS = PGAG * [V

- (V

- V

PIX

)]

= PGAG * V

PIX

XRD9827

RT -

PIX

BLK

Figure 19. CDS Timing (Triple Channel)

Mode: 110 00001110

XRD9825

Rev. 1.00

Mode 2. DC Coupled

Typical CCDs have outputs with black references.
Therefore, DC Coupled is not recommended for CCD
applications.

Offset Control DAC

The offset DAC is controlled by 8 bits. The offset range
is 800 mV ranging from -200 mV to +600 mV (when DB5
is set to 0) and -400 mV to +400 mV (when DB5 is set
to 1). Therefore, the resolution of the 8-Bit offset DAC
is 3.14 mV. However, the XRD9825 has +/- 100 mV
reserved for internal offsets. Therefore, the effective
range for adjusting for CIS offsets or black reference is
600 mV. The offset adjustment is used primarily to
correct for the difference between the black level of the
image sensor and the bottom ladder reference voltage
(VRB) of the ADC. By adjusting the black level to
correspond to VRB, the entire range of the ADC can be
used.

If the offset of the CIS output is greater than 500 mV an
external reference can be applied to VDCEXT. The
external reference can be used to adjust for large
offsets only when the internal mode is configured
through the serial port.

Since the offset DAC adjustment is done before the
gain stage, it is gain-dependent. For example, if the
gain needs to be changed between lines (red to blue,
etc.), the offset is calibrated before the signal passes
through the PGA.

PGA (Programmable Gain Amplifier) DAC

The gain of the input waveform is controlled by a 6-Bit
PGA. The PGA is used along with the offset DAC for
the purpose of using the entire range of the ADC. The
PGA has a linear gain from 1 to 10. Figure 19 is a plot
of the transfer curve for the PGA gain.

PGA GAIN TRANSFER CURVE

GAIN 1 - 10

CODE

GAIN

Figure 20. Transfer Curve for the 6-Bit PGA

After the signal is level shifted to correspond with the
bottom ladder reference voltage, the system can be
calibrated such that a white video pixel can represent
the top ladder reference voltage to the ADC. This allows
for a full scale conversion maximizing the resolution of
the ADC.

Analog to Digital Converter

The ADC is a 16-bit, 10 MSPS analog-to-digital con-
verter for high speed and high accuracy. The ADC uses
a subranging architecture to maintain low power con-
sumption at high conversion rates. The output of the
ADC is on an 8-bit databus. The 8-bit databus supports
8x8 output data. ADCCLK samples the input on its
falling edge. After the input is sampled, the MSB (8
upper bits) is latched to the output drivers. On the rising
edge of the ADCCLK, the LSB (8 lower bits) is latched
to the output drivers. The output needs to be
demultiplexed with external circuitry or a digital ASIC.
There is an 8 clock cycle latency (Config 00, 11) or 6
pixel count latency (Config 01, 10) for the analog-to-
digital converter.

The V

and V

reference voltages for the ADC are

generated internally, unless the external V

is se-

lected. In the external V

mode, the V

voltage is set

through the VREF+ pin. This allows the user to select
the dynamic range of the ADC.

XRD9825

Rev. 1.00

Serial Load Control Registers

The serial load registers are controlled by a three wire
serial interface through the bi-directional parallel port to
reduce the pin count of this device. When SYNCH is set
to high, the output bus is tri-stated and the serial
interface is activated. DB7/LD, DB5/SCLK and DB6/
SDATA are the three input signals that control this
process. The DB7/LD signal is set low to initiate the
loading of the internal registers.

There are internal registers that are accessed via an 11-
bit data string. Data is shifted in on the rising edge of
SCLK and loaded to the registers on the rising edge of
LD. The data on pin DB6/SDATA is latched automati-
cally after eleven DB5/SCLKs have been counted. If
eleven clocks are not present on DB5/SCLK before the
DB7/LD signal returns high, no data will be loaded into
the internal registers. If more than 11 clocks are
present on DB5/SCLK, the additional clocks will be
ignored. The data corresponding to the first eleven
DB5/SCLKs will be loaded only.

The first three MSBs choose which internal register will
be selected. The remaining 8 LSBs contain the data
needed for programming the internal register for a
particular configuration.

Power-Up State of the Internal Registers

The control register settings upon initial power-up are
for CIS, DC Coupled configuration (VRT is set to
internal, Input DC Reference=AGND and the input to
the ADC is selected through the RED channel). Gain is
unity and Offset is set to zero. The test modes are
disabled in the power-up state.

D B 6 / S D A T A

D B 5 / S C L K

S Y N C H

S 2

S 1

S 0

D 7

D 2

D 1

D 0

D B 7 / L D

tdl

tdz

tsclkw

tds tdh

Figure 21. Write Timing

XRD9825

Rev. 1.00

Output Bus Format

ADC Output --> DO15(MSB):DO0(LSB)

DB7

DB6

DB5

DB4

DB3

DB2

DB1

DB0

MSB

DO5

DO4

DO3

DO2

DO1

DO0

DO9

DO8

LSB

DO7

DO6

DO5

DO4

DO3

DO2

DO1

DO0

Note :

These are the control register settings upon initial power-up. The previous register settings are retained
following

a logic power-down initiated by the power down bit except the signal configuration. When de-selecting

the power down bit (D7 = 0, Normal), the signal configuration (D5 and D0) has to be reprogrammed.

MSB = 8 upper bits
LSB = 8 lower bits

Table 9. 8 MSB + 8 LSB Output Bus Format

XRD9825

Rev. 1.00

Function
(Register
S2/S1/S0)

Power-up

State

(Note 1)

Red Gain

000000XX

(000)

(MSB)

(LSB)

Red Offset

01000000

(001)

(MSB)

(LSB)

Grn Gain

000000XX

(010)

(MSB)

(LSB)

Grn Offset
(011)

01000000

(MSB)

(LSB)

Blu Gain
(100)

000000XX

(MSB)

(LSB)

Blu Offset
(101)

01000000

(MSB)

(LSB)

Mode

POWER

DIGITAL

INPUT DC

DC/AC

SIGNAL

00000000

(110)

DOWN

RESET

REFERENCE

POLARITY

CONFIGURATION

DCREF

)

0: NORMAL

0: NO RESET

0: INTERNAL

0: DC

0: Non-

00: Single-Channel

DCREF

=AGND)

Inverted

RED input/gain/offset

1:RESET

1: EXTERNAL

1: AC

(CIS)

POWER

(REGISTERS

DCREF

DCEXT

)

1: Inverted

01: Single-Channel

DOWN

ARE RESET TO

(CCD/CIS)

RED input

POWER-UP

RED/GRN/BLU

STATES)

gain/offset cycle

pixel-by-pixel

10: Triple-Channel

RED/GRN/BLU

input/gain/offset cycle

pixel-by-pixel

11: Triple-Channel

RED/GRN/BLU

input/gain/offset cycle

line-by-line

Mode

TEST5

OUTPUT

OFFSET

INTERNAL CIS

TEST4

TEST3

TEST2

TEST1

00000000

&Test

DISABLE

DAC

REFERENCE

(111)

RANGE

CIRCUIT

0:NOT USED

0:OUTPUTS

0:-200mV to

0:NORMAL

0: TEST4

0: TEST3

0: TEST2

0:NORMAL

ENABLED

+600mV

DISABLED

1:NORMAL

1:OUTPUTS

1:-400mV to

1:REFERENCE

1: OUTPUT

1: INPUT

1: TEST1

DISABLED

+400mV

CIRCUIT

OF BUFFER

OF PGA

OF ADC

ENABLED

TIED TO

BLU

VDCEXT

GRN

Control Registers

XRD9825

Rev. 1.00

NOTICE

EXAR Corporation reserves the right to make changes to the products contained in this publication in order to
improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any
circuits described herein, conveys no license under any patent or other right, and makes no representation that
the circuits are free of patent infringement. Charts and schedules contained here in are only for illustration
purposes and may vary depending upon a user's specific application. While the information in this publication
has been carefully checked; no responsibility, however, is assumed for in accuracies.

EXAR Corporation does not recommend the use of any of its products in life support applications where the
failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to
significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless
EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has
been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR Corporation is adequately
protected under the circumstances.

Copyright 2000 EXAR Corporation
Datasheet May 2000
Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited.

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: XRD9825

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: XRD9825