SPT7863
10-BIT, 40 MSPS, 160 mW A/D CONVERTER
TECHNICAL DATA
AUGUST 21, 2001
FEATURES
Monolithic 40 MSPS converter
160 mW power dissipation
On-chip track-and-hold
Single +5 V power supply
TTL/CMOS outputs
5 pF input capacitance
Low cost
Tri-state output buffers
High ESD protection: 3,500 V minimum
Selectable +3 V or +5 V logic I/O
APPLICATIONS
All high-speed applications where low power
dissipation is required
Video imaging
Medical imaging
Radar receivers
IR imaging
Digital communications
GENERAL DESCRIPTION
The SPT7863 is a 10-bit monolithic, low-cost, ultralow-
power analog-to-digital converter capable of minimum
word rates of 40 MSPS. The on-chip track-and-hold func-
tion assures very good dynamic performance without the
need for external components. The input drive require-
ments are minimized due to the SPT7863's low input
capacitance of only 5 pF.
Power dissipation is extremely low at only 160 mW typical
at 40 MSPS with a power supply of +5.0 V. The digital out-
puts are +3 V or +5 V, and are user selectable. The
SPT7863 is pin-compatible with an entire family of 10-bit,
CMOS converters (SPT7835/40/50/55/60/61), which sim-
plifies upgrades. The SPT7863 has incorporated propri-
etary circuit design and CMOS processing technologies to
achieve its advanced performance. Inputs and outputs are
TTL/CMOS-compatible to interface with TTL/CMOS logic
systems. Output data format is straight binary.
The SPT7863 is available in 28-lead SOIC and 32-lead
small (7 mm square) TQFP packages over the commer-
cial temperature range.
11-Bit
SAR
DAC
ADC Section 1
T/H
11
11-Bit
SAR
DAC
ADC Section 16
Auto-
Zero
CMP
Auto-
Zero
CMP
T/H
11
V
REF
1:16
Mux
11
11
11
11
11-Bit
16:1
Mux/
Error
Correction
Timing
and
Control
P1
P2
P15
P16
ADC Section 2
ADC Section 15
Reference Ladder
Ref
In
Enable
CLK In
Data
Valid
A
IN
D10 Overrange
D9 (MSB)
D8
D7
D6
D5
D4
D3
D2
D1
D0 (LSB)
.
.
.
.
.
.
.
.
.
.
.
.
BLOCK DIAGRAM
2
8/21/01
SPT7863
ABSOLUTE MAXIMUM RATINGS (Beyond which damage may occur)
1
25 C
Note: 1. Operation at any Absolute Maximum Rating is not implied. See
Electrical Specifications for proper nominal applied conditions
in typical applications.
ELECTRICAL SPECIFICATIONS
T
A
=T
MIN
to T
MAX
, AV
DD
=DV
DD
=OV
DD
=+5.0 V, V
IN
=0 to 4 V,
S
=40 MSPS, V
RHS
=4.0 V, V
RLS
=0.0 V, unless otherwise specified.
TEST
TEST
SPT7863
PARAMETERS
CONDITIONS
LEVEL
MIN
TYP
MAX
UNITS
Resolution
10
Bits
DC Accuracy
51% duty cycle
Integral Linearity Error (ILE)
VI
1.0
LSB
Differential Linearity Error (DLE)
VI
0.5
LSB
No Missing Codes
VI
Guaranteed
Analog Input
Input Voltage Range
VI
V
RLS
V
RHS
V
Input Resistance
IV
50
k
Input Capacitance
V
5.0
pF
Input Bandwidth
(Small Signal)
V
250
MHz
Offset
V
2.0
LSB
Gain Error
V
0.2
%
Reference Input
Resistance
VI
300
500
600
Bandwidth
V
100
150
MHz
Voltage Range
V
RLS
IV
0
2.0
V
V
RHS
IV
3.0
AV
DD
V
V
RHS
V
RLS
V
1.0
4.0
5.0
V
(V
RHF
V
RHS
)
V
90
mV
(V
RLS
V
RLF
)
V
75
mV
Reference Settling Time
V
RHS
V
15
Clock Cycles
V
RLS
V
20
Clock Cycles
Conversion Characteristics
Maximum Conversion Rate
VI
40
MHz
Minimum Conversion Rate
IV
2
MHz
Pipeline Delay (Latency)
IV
12
Clock Cycles
Aperture Delay Time
V
4.0
ns
Aperture Jitter Time
V
30
ps (p-p)
Dynamic Performance
Effective Number of Bits (ENOB)
IN
= 3.58 MHz
VI
9.2
Bits
IN
= 10 MHz
V
8.7
Bits
Signal-to-Noise Ratio (SNR)
(without Harmonics)
IN
= 3.58 MHz
VI
55
57
dB
IN
= 10 MHz
V
54
dB
Supply Voltages
AV
DD
...................................................................... +6 V
DV
DD
..................................................................... +6 V
Input Voltages
Analog Input .............................. 0.5 V to AV
DD
+0.5 V
V
REF
.............................................................. 0 to AV
DD
CLK Input ............................................................... V
DD
AV
DD
DV
DD
.................................................. 100 mV
AGND DGND .............................................. 100 mV
Output
Digital Outputs ................................................... 10 mA
Temperature
Operating Temperature ................................ 0 to 70 C
Junction Temperature ........................................ 175 C
Lead Temperature, (soldering 10 seconds) ....... 300 C
Storage Temperature ............................ 65 to +150 C
3
8/21/01
SPT7863
TEST LEVEL CODES
All electrical characteristics are subject to the
following conditions:
All parameters having min/max specifications
are guaranteed. The Test Level column indi-
cates the specific device testing actually per-
formed during production and Quality Assur-
ance inspection. Any blank section in the data
column indicates that the specification is not
tested at the specified condition.
LEVEL
TEST PROCEDURE
I
100% production tested at the specified temperature.
II
100% production tested at T
A
= +25 C, and sample tested at the
specified temperatures.
III
QA sample tested only at the specified temperatures.
IV
Parameter is guaranteed (but not tested) by design and characteri-
zation data.
V
Parameter is a typical value for information purposes only.
VI
100% production tested at T
A
= +25 C. Parameter is guaranteed
over specified temperature range.
ELECTRICAL SPECIFICATIONS
T
A
=T
MIN
to T
MAX
, AV
DD
=DV
DD
=OV
DD
=+5.0 V, V
IN
=0 to 4 V,
S
=40 MSPS, V
RHS
=4.0 V, V
RLS
=0.0 V, unless otherwise specified.
TEST
TEST
SPT7863
PARAMETERS
CONDITIONS
LEVEL
MIN
TYP
MAX
UNITS
Dynamic Performance
Total Harmonic Distortion (THD)
IN
= 3.58 MHz
VI
64
67
dB
IN
= 10 MHz
V
62
dB
Signal-to-Noise and Distortion
(SINAD)
IN
= 3.58 MHz
VI
54
57
dB
IN
= 10 MHz
V
54
dB
Spurious Free Dynamic Range
IN
= 3.580 MHz
V
70
dB
Differential Phase
V
0.3
Degree
Differential Gain
V
0.3
%
Inputs
Logic 1 Voltage
VI
2.0
V
Logic 0 Voltage
VI
0.8
V
Maximum Input Current Low
VI
10
+10
A
Maximum Input Current High
VI
10
+10
A
Input Capacitance
VI
+5
pF
Digital Outputs
Logic 1 Voltage
I
OH
= 0.5 mA
VI
3.5
V
Logic 0 Voltage
I
OL
= 1.6 mA
VI
0.4
V
t
RISE
15 pF load
V
10
ns
t
FALL
15 pF load
V
10
ns
Output Enable to Data Output Delay 20 pF load, T
A
= +25 C
V
10
ns
50 pF load over temp.
V
22
ns
Power Supply Requirements
Voltages
OV
DD
IV
3.0
5.0
V
DV
DD
IV
4.75
5.0
5.25
V
AV
DD
IV
4.75
5.0
5.25
V
Currents
AI
DD
VI
17
21
mA
DI
DD
VI
16
21
mA
Power Dissipation
VI
160
210
mW
4
8/21/01
SPT7863
APERTURE DELAY
Aperture delay represents the point in time, relative to the
rising edge of the CLOCK input, that the analog input is
sampled.
APERTURE JITTER
The variations in aperture delay for successive samples.
CLOCK DUTY CYCLE
Ratio of positive clock time (t
CH
) to total clock period (t
CLK
)
times 100%.
DIFFERENTIAL LINEARITY ERROR (DLE)
Error in the width of each code from its theoretical value.
(Theoretical = V
FS
/2
N
)
INTEGRAL LINEARITY ERROR (ILE)
Linearity error refers to the deviation of each individual
code (normalized) from a straight line drawn from FS
through +FS. The deviation is measured from the edge of
each particular code to the true straight line.
OUTPUT DELAY
Time between the clock's triggering edge and output data
valid.
OVERVOLTAGE RECOVERY TIME
The time required for the ADC to recover to full accuracy
after an analog input signal 125% of full scale is reduced
to 50% of the full-scale value.
SIGNAL-TO-NOISE RATIO (SNR)
The ratio of the fundamental sinusoid power to the total
noise power. Harmonics are excluded.
SIGNAL-TO-NOISE AND DISTORTION (SINAD)
The ratio of the fundamental sinusoid power to the total
noise and distortion power.
TOTAL HARMONIC DISTORTION (THD)
The ratio of the total power of the first 9 harmonics to the
power of the measured sinusoidal signal.
SPURIOUS FREE DYNAMIC RANGE (SFDR)
The ratio of the fundamental sinusoidal amplitude to the
single largest harmonic or spurious signal.
N =
SINAD 1.76
6.02
SPECIFICATION DEFINITIONS
DIFFERENTIAL GAIN (DG)
A signal consisting of a sine wave superimposed on vari-
ous DC levels is applied to the input. Differential gain is the
maximum variation in the sampled sine wave amplitudes
at these DC levels.
DIFFERENTIAL PHASE (DP)
A signal consisting of a sine wave superimposed on vari-
ous DC levels is applied to the input. Differential phase is
the maximum variation in the sampled sine wave phases
at these DC levels.
EFFECTIVE NUMBER OF BITS (ENOB)
SINAD = 6.02N + 1.76, where N is equal to the effective
number of bits.
Duty Cycle =
t
CH
t
CLK
X 100%
INPUT BANDWIDTH
Small signal (50 mV) bandwidth (3 dB) of analog input
stage.
5
8/21/01
SPT7863
Figure 1A Timing Diagram 1
ANALOG IN
CLOCK IN
1
3
5
7
9
11
13
15
17
SAMPLING
CLOCK
(Internal)
DATA OUTPUT
DATA VALID
VALID
INVALID
1
3
2
4
5
Figure 1B Timing Diagram 2
t
OD
Data 0
Data 1
Data 2
Data 3
CLOCK IN
DATA
OUTPUT
DATA VALID
t
CH
t
CL
t
S
t
S
t
CL
t
CH
t
C
t
CLK
Table I Timing Parameters
DESCRIPTION
PARAMETERS
MIN
TYP
MAX
UNITS
Conversion Time
t
C
t
CLK
ns
Clock Period
t
CLK
25
ns
Clock to Output Delay (15 pF Load)
t
OD
17
ns
Clock to DAV
t
S
10
ns
PDF 
ZIP