FPD3000P100
2W
P
ACKAGED
P
OWER P
HEMT
Phone: +1 408 850-5790
http://www.filtronic.co.uk/semis
Released: 6/27/05
Fax: +1 408 850-5766
Email: sales@filcsi.com
FEATURES
32.5 dBm Linear Output Power
17 dB Power Gain at 2 GHz
9.5 dB Maximum Stable Gain at 10 GHz
42 dBm Output IP3
45% Power-Added Efficiency at 2 GHz
DESCRIPTION AND APPLICATIONS
The FPD3000P100 is a packaged AlGaAs/InGaAs pseudomorphic High Electron Mobility
Transistor (PHEMT), featuring a 0.25
m by 3000 m Schottky barrier gate, defined by high-
resolution stepper-based photolithography. The recessed and offset Gate structure minimizes
parasitics to optimize performance. The epitaxial structure and processing have been optimized for
reliable high-power applications. The FPD3000P100 also features Si
3
N
4
passivation and is also
available in die form and in the low cost plastic SOT89 plastic package.
Typical applications include commercial and other narrowband and broadband high-performance
amplifiers, including SATCOM uplink transmitters, PCS/Cellular low-voltage high-efficiency output
amplifiers, and medium-haul digital radio transmitters.
ELECTRICAL SPECIFICATIONS AT 22C
Parameter
Symbol
Test Conditions
Min
Typ
Max
Units
UNLESS OTHERWISE NOTED, RF SPECIFICATIONS MEASURED AT f = 2 GHz USING CW SIGNAL
Power at 1dB Gain Compression
P
1dB
V
DS
= 8 V; I
DS
= 50% I
DSS
31.0
32.5 dBm
Power Gain at P
1dB
G
1dB
V
DS
= 8 V; I
DS
= 50% I
DSS
16.5
17.0 dB
Maximum Stable Gain (S
21
/S
12
) SSG V
DS
= 8 V; I
DS
= 50% I
DSS
f = 2 GHz
f = 10 GHz
20.5
8.5
21.5
9.5
dB
dB
Power-Added Efficiency
PAE
V
DS
= 8 V; I
DS
= 50% I
DSS
;
P
OUT
= P
1dB
45 %
Output Third-Order Intercept Point
(from 15 to 5 dB below P
1dB
)
IP3 V
DS
= 8V; I
DS
= 50% I
DSS
Matched for optimal power
42
dBm
Saturated Drain-Source Current
I
DSS
V
DS
= 1.3 V; V
GS
= 0 V
750
930
1110
mA
Maximum Drain-Source Current
I
MAX
V
DS
= 1.3 V; V
GS
+1 V
1.5 A
Transconductance G
M
V
DS
= 1.3 V; V
GS
= 0 V
800
mS
Gate-Source Leakage Current
I
GSO
V
GS
= -5 V
2
20
A
Pinch-Off Voltage
|V
P
| V
DS
= 1.3 V; I
DS
= 3 mA
0.7
1.0
1.3
V
Gate-Drain Breakdown Voltage
|V
BDGD
| I
GD
= 3 mA
14.5
16.0
V
Thermal Resistivity (see Notes)
JC
V
DS
>
6V
24
C/W
FPD3000P100
2W
P
ACKAGED
P
OWER P
HEMT
Phone: +1 408 850-5790
http://www.filtronic.co.uk/semis
Released: 6/27/05
Fax: +1 408 850-5766
Email: sales@filcsi.com
RECOMMENDED BIAS CONDITIONS:
Drain-Source Voltage:
5V to 8V
Drain-Source Current:
33% to 50% I
DSS
ABSOLUTE MAXIMUM RATINGS
1
Parameter
Symbol
Test Conditions
Min
Max
Units
Drain-Source Voltage
V
DS
-3V < V
GS
< +0V
9
V
Gate-Source Voltage
V
GS
0V < V
DS
< +8V
-3
V
Drain-Source Current
I
DS
For V
DS
> 2V
I
DSS
mA
Gate Current
I
G
Forward or reverse current
25
mA
RF Input Power
2
P
IN
Under any acceptable bias state
600
mW
Channel Operating Temperature
T
CH
Under any acceptable bias state
175
C
Storage Temperature
T
STG
Non-Operating Storage
-40
150
C
Total Power Dissipation
P
TOT
See De-Rating Note below
5.3
W
Gain Compression
Comp.
Under any bias conditions
5
dB
Simultaneous Combination of Limits
3
2 or more Max. Limits
80
%
1
T
Ambient
= 22
C unless otherwise noted
2
Max. RF Input Limit must be further limited if input VSWR > 2.5:1
3
Users should avoid exceeding 80% of 2 or more Limits simultaneously
Notes:
Operating conditions that exceed the Absolute Maximum Ratings could result in permanent damage to the device.
Thermal Resitivity specification assumes a Au/Sn eutectic die attach onto a Au-plated copper heatsink or rib.
Power Dissipation defined as: P
TOT
(P
DC
+ P
IN
) P
OUT
, where
P
DC
: DC Bias Power
P
IN
: RF Input Power
P
OUT
: RF Output Power
Absolute Maximum Power Dissipation to be de-rated as follows above 22C:
P
TOT
= 5.3W (0.042W/
C) x T
HS
where T
HS
= heatsink or ambient temperature above 22
C
Example: For a 85
C heatsink temperature: P
TOT
= 5.3W (0.042 x (85 22)) = 2.65
HANDLING PRECAUTIONS
To avoid damage to the devices care should be exercised during handling. Proper Electrostatic
Discharge (ESD) precautions should be observed at all stages of storage, handling, assembly, and
testing. These devices should be treated as Class 0 (< 250V) per JESD22-A114-B, Human Body
Model, and Class A (< 200V) per JESD22-A115-A, Machine Model.
FPD3000P100
2W
P
ACKAGED
P
OWER P
HEMT
Phone: +1 408 850-5790
http://www.filtronic.co.uk/semis
Released: 6/27/05
Fax: +1 408 850-5766
Email: sales@filcsi.com
APPLICATIONS NOTES & DESIGN DATA
Applications Notes are available from your local Filtronic Sales Representative or directly from the
factory. Complete design data, including S-parameters, noise data, and large-signal models are
available on the Filtronic web site.
RECOMMENDED BIASING GUIDELINES:
For most applications, a dual-bias circuit is required due to the amount of quiescent current drawn by
the FPD3000P100. The Source of the discrete pHEMT device is wire-bonded to the package flange,
and therefore self-biasing (using a bypassed Source resistor to set the Gate-Source voltage) is not
practical. A dual-bias circuit will require a regulated and filtered negative Gate supply as well as a
positive Drain supply. Typical Gate bias voltages will be about -0.4V. Active bias circuits can be
employed if the dissipation by a Drain current sense resistor is acceptable, and in these cases the bias
voltages must be sequenced so that the negative Gate voltage is established at its final value before
the Drain voltage is reached, to prevent device self-oscillation.
All information and specifications are subject to change without notice.
PDF 
ZIP