ChipFind - документация

Электронный компонент: D5CCD1

Скачать:  PDF   ZIP

Document Outline

DS04-23116-2E
FUJITSU MEDIA DEVICE
DATA SHEET
ASSP Mobile Communication Systems
SAW Duplexer
(700 to 1000 MHz)
D5CC Series (D1)
s
s
s
s
DESCRIPTION
The D5CC series of SAW antenna duplexer apply to the frequency range 700 to 1000 MHz.
The SAW filters are fabricated on a piezoelectric-crystal unit (LiTaO
3
:lithium tantalate) with a large electrome-
chanical dissociation.
The D5CC series provides small size and light duplexer by using original design, mounting and electrode formation
techniques.
D5CC(D1) series are incorporated transmitter filter and receiver filter into a small package and are housed phase
circuit in the package. Moreover, I/O of SAW filter is set to impedance 50
, so application requires no external
circuits.
s
s
s
s
FEATURES
Ultra compact and light package (0.14cm
3
, 9.5
7.5
2.0 (h) mm Typ.)
External matching circuits are not required.
Surface mount package (SMT)
High handling power resistance (1.2 W Max.)
s
s
s
s
PACKAGE
D5CC Series (D1)
2
s
s
s
s
PIN ASSIGNMENT
(TOP VIEW)
(BOTTOM VIEW)
F
C 8
0 1
B
11
12
13
14
15
7
6
5
10
9
8
1
16
2
3
4
1
16
15
14
13
5
6
7
2
3
4
11
12
10
9
8
D5CC Series (D1)
3
s
s
s
s
PIN DESCRIPTION
* : Only one Antenna pin should be connected.
The remaining Antenna pin doesnot have to be connected.
Pin No.
Pin name
Description
1
GND
Ground Pin
2
ANT
Antenna Pin*
3
GND
Ground Pin
4
GND
Ground Pin
5
GND
Ground Pin
6
Rx
Receiver side Pin
7
GND
Ground Pin
8
GND
Ground Pin
9
GND
Ground Pin
10
ANT
Antenna Pin*
11
GND
Ground Pin
12
GND
Ground Pin
13
GND
Ground Pin
14
Tx
Transmitter side Pin
15
GND
Ground Pin
16
GND
Ground Pin
D5CC Series (D1)
4
s
s
s
s
ABSOLUTE MAXIMUM RATINGS
WARNING: Piezoelectric devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
s
s
s
s
RECOMMENDED OPERATING CONDITIONS
WARNING: The recommended operating conditions are required in order to ensure the normal operation of the
piezoelectric device. All of the device's electrical characteristics are warranted when the device is
operated within these ranges.
Always use piezoelectric devices within their recommended operating condition ranges. Operation
outside these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented on
the data sheet. Users considering application outside the listed conditions are advised to contact their
FUJITSU representatives beforehand.
s
s
s
s
STANDARD FREQUENCIES
Parameter
Symbol
Rating
Unit
Min.
Max.
Operating temperature
Ta
-
30
+
85
C
Storage temperature
Tstg
-
40
+
100
C
Maximum input power
P
IN
1.2
W
Input DC voltage
-
5
+5
V
Parameter
Symbol
Value
Unit
Min.
Max.
Operating temperature
Ta
-
30
+
85
C
System
Tx freq.
(MHz)
Rx freq.
(MHz)
Part number
Part
symbol
Remarks
AMPS/IS-95/IS-136
824 to 849
869 to 894
FAR-D5CC-881M50-D1C8
C8
D5CC Series (D1)
5
s
s
s
s
ELECTRICAL CHARACTERISTICS
AMPS/IS-136/IS-95
1.
Part number : FAR-D5CC-881M50-D1C8
(Ta
=
-
30
C to
+
85
C)
Parameter
Condition
Value
Unit
Remarks
Min.
Typ.
Max.
Tx
Antenna
Insertion Loss
824 to 849 MHz
2.0
2.5
dB
+
15 to
+
35
C
2.7
dB
-
30 to
+
85
C
Inband Ripple
824 to 849 MHz
1.0
1.5
dB
VSWR
(Return loss)
842 to 849 MHz
(7.4)
1.8
(10.9)
2.5
(
)
(dB)
Absolute
Attenuation
779 to 804 MHz
12
17
dB
869 to 894 MHz
40
46
dB
1648 to 1698 MHz
6
9
dB
2472 to 2547 MHz
6
8
dB
Antenna
Rx
Insertion Loss
869 to 894 MHz
3.8
4.3
dB
Inband Ripple
869 to 894 MHz
1.5
2.5
dB
VSWR
(Return loss)
869 to 894 MHz
(6.8)
2.3
(8.1)
2.7
(
)
(dB)
Absolute
Attenuation
824 to 849 MHz
50
55
dB
930 to 1200 MHz
40
43
dB
1200 to 1500 MHz
40
43
dB
1500 to 1800MHz
40
45
dB
Tx
Rx
Absolute
Attenuation
(Isolation)
824 to 849 MHz
53
55
dB
869 to 894 MHz
46
49
dB
+
15 to
+
85
C
43
dB
-
30 to
+
15
C
Maximum Input Power
Ta
=
+
50
C
1.2 W (continuous wave
>
50000 h)
D5CC Series (D1)
6
Typical Characteristics
1
1
2
2
3
3
4
4
S21
log MAG
10 dB/
REF 0 dB
1 :
-
1.9803 dB
824 MHz
2 :
-
1.7331 dB
849 MHz
3 :
-
61.585 dB
869 MHz
4 :
-
47.689 dB
894 MHz
T
X
1 :
-
62.318 dB
824 MHz
2 :
-
57.892 dB
849 MHz
3 :
-
3.3498 dB
869 MHz
4 :
-
3.3633 dB
894 MHz
R
X
T
X
R
X
START 760 MHz
STOP 960 MHz
1
2
3
S21
log MAG
10 dB/
REF 0 dB
START 760 MHz
STOP 960 MHz
1 :
-
59.654 dB
824 MHz
2 :
-
68.072 dB
849 MHz
3 :
-
53.411 dB
869 MHz
4 :
-
54.842 dB
894 MHz
T
X
R
X
Isolation
4
D5CC Series (D1)
7
1
2
4
5
4
3
2
5
3
S21
log MAG
5 dB/
REF 0 dB
START .030 MHz
STOP 3 000.000 MHz
1 :
-
1.564 dB
836.5 MHz
2 :
-
10.596 dB
1.648 GHz
3 :
-
9.3088 dB
1.698 GHz
4 :
-
10.209 dB
2.472 GHz
5 :
-
7.4124 dB
2.547 GHz
T
X
1 :
-
2.5972 dB
881.5 MHz
2 :
-
40.83 dB
1 GHz
3 :
-
47.85 dB
1.5 GHz
4 :
-
37.591 dB
2 GHz
5 :
-
32.402 dB
2.5 GHz
R
X
T
X
R
X
1
D5CC Series (D1)
8
s
s
s
s
MEASURMENT CIRCUIT
s
s
s
s
PART NUMBER DESIGNATION
[Designation example]
(1) Frequency : Specify the nominal center frequency of higher frequency side in six alphanumeric.
Enter M (for MHz) at the decimal point. Refer to below example.
[Example] 881.5 MHz
881M50
(2) Part symbol : Specified characters from A1 to Z9.
(3) Packing : T : 1 k pcs/reel
Q : 2 k pcs/reel
(1) Tx
ANT
(2) ANT
Rx
10
3 4
11 12
1
9
5 7
13 15
8
16
14
6
Tx
50
ANT
2
3 4
11
1
9
8
16
12
5 7
13 15
6
14
Rx
50
ANT
10
3 4
11 12
1
9
5 7
13 15
8
16
14
2
6
Tx
50
ANT
2
3 4
11
1
9
8
16
12
5 7
13 15
6
10
14
Rx
50
ANT
Open
Open
10
3 4
11 12
1
9
5 7
13 15
8
16
14
2
6
Tx
50
R
X
Open
(3)Tx
Rx
FAR
-
D5CC
-
-
D1
-
(1)
(2) (3)
D5CC Series (D1)
9
s
s
s
s
MARKING
F
C 8
0 1
B
Part Symbol
Lot Number
Logo
Data
(EIAJ standard)
Index
D5CC Series (D1)
10
s
s
s
s
PACKAGE DIMENSION
9.5
2.2 Max.
3.75
1.27
16
-
R0.2
2.54
4.75
1.1
0.8
4.6
6.8
7.5
0.6
F
C 8
0 1
B
0.8
0.8
Dimensions in mm.
D5CC Series (D1)
11
s
s
s
s
RECOMMENDED LAND PATTERN
Note : Only one Antenna pin should be connected.
The remaining Antenna pin does not have to be connected.
0.8
0.8
1.27
7.5
3.75
1.0
0.3
4 - C 0.3
0.3
1.0
2.54
2.54
4.75
9.5
Dimensions in mm.
D5CC Series (D1)
12
s
s
s
s
PACKING : Reel type
(1) Reel Dimensions
(2) Packing Style
2
0.5
13.0
0.2
21
0.8
R1.0
330
80
16.4
22.4 Max.
2.0
0.0
Dimensions in mm.
Type
A
Volume
-T
330
1 k pcs
-Q
330
2 k pcs
Index
Pulling side
Pulling side
Reel side
D5CC Series (D1)
13
(3) Tape Dimensions
(4) Peel strength of top cover tape
4.0
0.1
2.0
0.1
7.5

0.1
10.0

0.1
0.3
16.0

0.3
12.0
0.1
1.75

0.1
2.5
0.1
8.0
0.1
1.5
0.1
0
1.6
Dimensions in mm.
165 to 185
Direction of pulling
Speed 300 mm/min
Embossment carrier type tape
Peel off by the force of 0.1 N to 0.7 N
under the condition at the right.
(Conforms to JIS C 0806 section 5.2)
D5CC Series (D1)
14
s
s
s
s
RECOMMENDED REFLOW PROFILE
s
s
s
s
NOTE
Mass-produced product order is accepted by a unit of 1000.
240
210
150
Time (s)
Pre-Heating
10 s
60 s
60 to 90 s
Temperature (
C)
Heating rate
1 to 4
C/s
Air cooling
D5CC Series (D1)
FUJITSU MEDIA DEVICES LIMITED
All Rights Reserved.
The contents of this document are subject to change without notice.
Customers are advised to consult with FUJITSU MEDIA
DEVICES sales representatives before ordering.
The information and circuit diagrams in this document are
presented as examples of device applications, and are not intended
to be incorporated in devices for actual use. Also, FUJITSU
MEDIA DEVICES is unable to assume responsibility for
infringement of any patent rights or other rights of third parties
arising from the use of this information or circuit diagrams.
The products described in this document are designed, and
manufactured as contemplated for general use, including without
limitation, ordinary industrial use, general office use, personal use,
and household use, but are not designed, developed and
manufactured as contemplated (1) for use accompanying fatal risks
or dangers that, unless extremely high safety is secured, could have
a serious effect to the public, and could lead directly to death,
personal injury, severe physical damage or other loss (i.e., nuclear
reaction control in nuclear facility, aircraft flight control, air traffic
control, mass transport control, medical life support system, missile
launch control in weapon system), or (2) for use requiring
extremely high reliability (i.e., submersible repeater and artificial
satellite).
Please note that Fujitsu will not be liable against you and/or any
third party for any claims or damages arising in connection with
above-mentioned uses of the products.
Any electronic devices have inherently a certain rate of failure. You
must protect against injury, damage or loss from such failures by
incorporating safety design measures into your facility and
equipment such as redundancy, fire protection, and prevention of
over-current levels and other abnormal operating conditions.
If any products described in this document represent goods or
technologies subject to certain restrictions on export under the
Foreign Exchange and Foreign Trade Control Law of Japan, the
prior authorization by Japanese government should be required for
export of those products from Japan.
F0010
FUJITSU LIMITED Printed in Japan