ChipFind - документация

Электронный компонент: MB15F08SLPV1

Скачать:  PDF   ZIP

Document Outline

1
DS04-21362-2E
FUJITSU SEMICONDUCTOR
DATA SHEET
ASSP
Dual Serial Input
PLL Frequency Synthesizer
MB15F08SL
s
DESCRIPTION
The Fujitsu MB15F08SL is a serial input Phase Locked Loop (PLL) frequency synthesizer with a 2500 MHz and a
1100 MHz prescalers. The 2500 MHz prescaler, and 1100 MHz prescaler have a dual modulus division ratio of 32/
33 or 64/65 and 16/17 or 32/33 enabling pulse swallow operation.
The supply voltage range is between 2.4 V and 3.6 V.
The MB15F08SL uses the latest BiCMOS process. As a result, the supply current is typically 7.0 mA at 2.7 V. A
refined charge pump supplies a well-balanced output current of 1.5 mA or 6 mA. The charge pump current is selectable
by serial data.
MB15F08SL is ideally suited for wireless mobile communications.
s
FEATURES
High frequency operation: RX synthesizer: 2500 MHz max
TX synthesizer: 1100 MHz max
Low power supply voltage: V
CC
= 2.4 to 3.6 V
Ultra Low power supply current: I
CC
= 7.0 mA typ. (V
CC
= 2.7 V, Ta = +25
C, in TX, RX locking state)
I
CC
= 7.5 mA typ. (V
CC
= 3.0 V, Ta = +25
C, in TX, RX locking state)
Direct power saving function: Power supply current in power saving mode
Typ. 0.1
A (V
CC
= 3V, Ta = +25
C), Max. 10
A (V
CC
= 3V)
Dual modulus prescaler: 2500 MHz prescaler (32/33 or 64/65)/1100 MHz prescaler (16/17 or 32/33)
Serial input 14-bit programmable reference divider: R = 3 to 16,383
Serial input programmable divider consisting of:
- Binary 7-bit swallow counter: 0 to 127
- Binary 11-bit programmable counter: 3 to 2,047
Software selectable charge pump current
Onchip phase control for phase comparator
Operating temperature: Ta = 40 to +85
C
s
PACKAGES
16-pin, Plastic SSOP
(FPT-16P-M05)
16-pad, Plastic BCC
(LCC-16P-M04)
2
MB15F08SL
s
PIN ASSIGNMENTS
GND
RX
OSC
IN
GND
TX
fin
TX
V
CCTX
LD/fout
PS
TX
D
OTX
Clock
Data
LE
fin
RX
V
CCRX
Xfin
RX
PS
RX
D
ORX
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
GND
RX
Clock
D
OTX
D
ORX
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
OSC
IN
GND
TX
fin
TX
V
CCTX
PS
TX
LD/fout
Data
LE
fin
RX
V
CCRX
PS
RX
Xfin
RX
TOP
VIEW
TOP
VIEW
(FPT-16P-M05)
(LCC-16P-M04)
16-pin SSOP
16-pad BCC
3
MB15F08SL
s
PIN DESCRIPTION
Pin no.
Pin
name
I/O
Descriptions
SSOP
BCC
1
16
GND
RX
Ground for RX-PLL section.
2
1
OSC
IN
I
The programmable reference divider input. TCXO should be connected
with a AC coupling capacitor.
3
2
GND
TX
Ground for the TX-PLL section.
4
3
fin
TX
I
Prescaler input pin for the TX-PLL.
Connection to an external VCO should be via AC coupling.
5
4
V
CCTX
Power supply voltage input pin for the TX-PLL section.
6
5
LD/fout
O
Lock detect signal output (LD)/phase comparator monitoring
output (fout).
The output signal is selected by LDS bit in the serial data.
LDS bit = "H" ; outputs fout signal
LDS bit = "L" ; outputs LD signal
7
6
PS
TX
I
Power saving mode control for the TX-PLL section. This pin must be set at
"L" during Power-ON. (Open is prohibited.)
PS
TX
= "H" ; Normal mode
PS
TX
= "L" ; Power saving mode
8
7
Do
TX
O
Charge pump output for the TX-PLL section.
Phase characteristics of the phase detector can be selected via
programming of the FC-bit.
9
8
Do
RX
O
Charge pump output for the RX-PLL section.
Phase characteristics of the phase detector can be selected via
programming of the FC-bit.
10
9
PS
RX
I
Power saving mode control for the RX-PLL section. This pin must be set at
"L" during Power-ON. (Open is prohibited.)
PS
RX
= "H" ; Normal mode
PS
RX
= "L" ; Power saving mode
11
10
Xfin
RX
I
Prescaler complementary input for the RX-PLL section.
This pin should be grounded via a capacitor.
12
11
V
CCRX
Power supply voltage input pin for the RX-PLL section, the shift register
and the oscillator input buffer. When power is OFF, latched data of RX-PLL
is lost.
13
12
fin
RX
I
Prescaler input pin for the RX-PLL.
Connection to an external VCO should be via AC coupling.
14
13
LE
I
Load enable signal inpunt (with a schmitt trigger input buffer.)
When the LE bit is set "H", data in the shift register is transferred to the
corresponding latch according to the control bit in the serial data.
15
14
Data
I
Serial data input (with a schmitt trigger input buffer.)
A data is transferred to the corresponding latch (TX-ref counter, TX-prog.
counter, RX-ref. counter, RX-prog. counter) according to the control bit in
the serial data.
16
15
Clock
I
Clock input for the 23-bit shift register (with a schmitt trigger input buffer.)
One bit of data is shifted into the shift register on a rising edge of the clock.
4
MB15F08SL
s
BLOCK DIAGRAM
16
Clock
15
Data
14
LE
10
PS
RX
11
Xfin
RX
13
fin
RX
OSC
IN
fin
TX
PS
TX
3-bit latch
7-bit latch
11-bit latch
3-bit latch
Latch selector
23-bit shift register
7-bit latch
11-bit latch
Phase
comp.
(TX-PLL)
Lock
Det.
(TX-PLL)
Lock
Det.
(RX-PLL)
Charge
pump.
(TX-PLL)
Current
Switch
Phase
comp.
(RX-PLL)
Charge
pump.
(RX-PLL)
Current
Switch
2-bit latch
14-bit latch
1-bit latch
2-bit latch
14-bit latch
1-bit latch
Intermittent
mode control
(TX-PLL)
Intermittent
mode control
(RX-PLL)
Schmitt
circuit
Schmitt
circuit
Schmitt
circuit
Binary 7-bit
swallow counter
(TX-PLL)
Binary 14-bit
programmable ref.
counter (TX-PLL)
C/P setting
current
Binary 11-bit
programmable
counter (TX-PLL)
Binary 7-bit
swallow counter
(RX-PLL)
Binary 11-bit
programmable
counter (RX-PLL)
Prescaler
(TX-PLL)
16/17, 32/33
Prescaler
(RX-PLL)
32/33, 64/65
FC
TX
SW
TX
LDS
FC
RX
SW
RX
LDS
V
CCTX
GND
TX
5
3
fp
TX
8 Do
TX
LD
TX
Selector
T1
T2
T1
T2
9 Do
RX
OR
6 LD
/
fout
fr
RX
fp
RX
fr
TX
C
N
1
C
N
2
AND
LD
fr
TX
fr
RX
fp
TX
fp
RX
V
CCRX
GND
RX
7
(6)
(3)
(1)
(12)
(10)
(9)
(13)
(14)
(15)
4
2
(8)
(5)
(7)
(2)
(4)
Binary 14-bit
programmable ref.
counter (RX-PLL)
C/P setting
current
1-bit latch
12
(11)
1 (16)
O -- SSOP
( ) -- BCC
5
MB15F08SL
s
ABSOLUTE MAXIMUM RATINGS
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
s
RECOMMENDED OPERATING CONDITIONS
WARNING: The recommended operating conditions are required in order to ensure the normal operation of the
semiconductor device. All of the device's electrical characteristics are warranted when the device is
operated within these ranges.
Always use semiconductor devices within their recommended operating condition ranges. Operation
outside these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented on
the data sheet. Users considering application outside the listed conditions are advised to contact their
FUJITSU representatives beforehand.
Parameter
Symbol
Rating
Unit
Remark
Min.
Max.
Power supply voltage
V
CC
0.5
+4.0
V
Input voltage
V
I
0.5
V
CC
+0.5
V
Output voltage
V
O
GND
V
CC
V
Storage temperature
T
stg
55
+125
C
Parameter
Symbol
Value
Unit
Remark
Min.
Typ.
Max.
Power supply voltage
V
CC
2.4
3.0
3.6
V
Input voltage
V
I
GND
V
CC
V
Operating temperature
Ta
40
+85
C