DS05-50211-1E
FUJITSU SEMICONDUCTOR
DATA SHEET
Stacked MCP (Multi-Chip Package) FLASH MEMORY & SRAM
CMOS
64M (
8/
16) FLASH MEMORY &
8M (
8/
16) STATIC RAM
MB84VD23280EA
-90
/MB84VD23280EE
-90
s
FEATURES
Power supply voltage of 2.7 V to 3.3 V
High performance
90 ns maximum access time (Flash)
70 ns maximum access time (SRAM)
Operating Temperature
25
C to +85
C
Package 101-ball BGA
(Continued)
s
PRODUCT LINEUP
s
PACKAGE
Flash Memory
SRAM
Ordering Part No.
V
CC
f, V
CC
s = 3.0 V
MB84VD23280EA-90/MB84VD23280EE-90
Max. Address Access Time (ns)
90
70
Max. CE Access Time (ns)
90
70
Max. OE Access Time (ns)
35
35
101-pin plastic FBGA
BGA-101P-M01
+0.3V
0.3 V
MB84VD23280EA-90/MB84VD23280EE-90
2
(Continued)
-- FLASH MEMORY
Simultaneous Read/Write operations (flex bank)
Two virtual Banks are chosen from the combination of four physical banks
Host system can program or erase in one bank, then read immediately and simultaneously read from the other
bank between read and write operations
Read-while-erase
Read-while-program
Minimum 100,000 write/erase cycles
Sector erase architecture
Sixteen 4 K words and one hundred twenty-six 32 K word.
Any combination of sectors can be concurrently erased. Also supports full chip erase.
Embedded Erase
TM
* Algorithms
Automatically pre-programs and erases the chip or any sector
Embedded Program
TM
* Algorithms
Automatically writes and verifies data at specified address
Data Polling and Toggle Bit feature for detection of program or erase cycle completion
Ready-Busy output (RY/BY)
Hardware method for detection of program or erase cycle completion
Automatic sleep mode
When addresses remain stable, automatically switch themselves to low power mode.
Low V
CC
write inhibit
2.5 V
Hidden ROM (Hi-ROM) region
256 byte of Hi-ROM, accessible through a new "Hi-ROM Enable" command sequence
Factory serialized and protected to provide a secure electronic serial number (ESN)
WP/ACC input pin
At V
IL
, allows protection of 2 of 8 Kbytes on both ends of each boot sector, regardless of sector protection/
unprotection status.
At V
IH
, allows removal of boot sector protection
At V
ACC
, increases program performance
Program Suspend/Resume
Suspends the program operation to allow a read in another address
Erase Suspend/Resume
Suspends the erase operation to allow a read in another sector within the same device
Please refer to "MBM29DL640E" data sheet in detailed function
-- SRAM
Power dissipation
Operating : 50 mA Max.
Standby : 25
A Max.
Power down features using CE1s and CE2s
Data retention supply voltage: 1.5 V to 3.3 V
CE1s and CE2s Chip Select
Byte data control: LBs (DQ
7
-DQ
0
), UBs (DQ
15
-DQ
8
)
*: Embedded Erase
TM
and Embedded Program
TM
are trademarks of Advanced Micro Devices, Inc.
MB84VD23280EA-90/MB84VD23280EE-90
4
s
s
s
s
PIN DESCRIPTION
Pin name
Input/
Output
Description
A
18
to A
0
I
Address Inputs (Common)
A
21
to A
19
, A
1
I
Address Inputs (Flash)
SA
I
Address Input (SRAM)
DQ
15
to DQ
0
I/O
Data Inputs/Outputs (Common)
CEf
I
Chip Enable (Flash)
CE1s
I
Chip Enable (SRAM)
CE2s
I
Chip Enable (SRAM)
OE
I
Output Enable (Common)
WE
I
Write Enable (Common)
RY/BY
O
Ready/Busy Output (Flash) Open Drain Output
UBs
I
Upper Byte Control (SRAM)
LBs
I
Lower Byte Control (SRAM)
CIOf
I
I/O Configuration (Flash)
CIOf = V
IH
is Word mode (16), CIOf = V
IL
is Byte mode (8)
CIOs
I
I/O Configuration (SRAM)
CIOs = V
IH
is Word mode (16), CIOs = V
IL
is Byte mode (8)
RESET
I
Hardware Reset Pin/Sector Protection Unlock (Flash)
WP/ACC
I
Write Protect / Acceleration (Flash)
N.C.
--
No Internal Connection
V
SS
Power
Device Ground (Common)
V
CC
f
Power
Device Power Supply (Flash)
V
CC
s
Power
Device Power Supply (SRAM)