DS07-12601-1E
FUJITSU SEMICONDUCTOR
DATA SHEET
8-bit Proprietary Microcontrollers
CMOS
F
2
MC-8FX MB95100A Series
MB95107A/F108AS/F108AW/FV100A-101
DESCRIPTION
The MB95100A series is general-purpose, single-chip microcontrollers. In addition to a compact instruction set,
the microcontrollers contain a variety of peripheral functions.
FEATURE
F
2
MC-8FX CPU core
Instruction set optimized for controllers
Multiplication and division instructions
16-bit arithmetic operations
Bit test branch instruction
Bit manipulation instructions etc.
Clock
Main clock
Main PLL clock
Subclock (for dual clock product)
Sub PLL clock (for dual clock product)
(Continued)
PACKAGES
64-pin plastic LQFP
64-pin plastic LQFP
(FPT-64P-M03)
(FPT-64P-M09)
MB95100A Series
2
(Continued)
Timer
8/16-bit compound timer
2 channels
16-bit reload timer
8/16-bit PPG
2 channels
16-bit PPG
2 channels
Timebase timer
Watch prescaler (for dual clock product)
LIN-UART
Full duplex double buffer
Clock asynchronous or synchronous serial transfer capable
UART/SIO
Clock asynchronous or synchronous serial transfer capable
I
2
C*
Built-in wake-up function
External interrupt
Interrupt by edge detection (rising, falling, or both edges can be selected)
Can be used to recover from low-power consumption modes.
10-bit A/D converter
10-bit resolution
Low-power consumption (standby mode)
Stop mode
Sleep mode
Watch mode (for dual clock product)
Timebase timer mode
I/O port: Max 55
General-purpose I/O ports (Nch open drain) : 6 ports
General-purpose I/O ports (CMOS)
: 49 ports
* : Purchase of Fujitsu I
2
C components conveys a license under the Philips I
2
C Patent Rights to use, these com-
ponents in an I
2
C system provided that the system conforms to the I
2
C Standard Specification as defined by
Philips.
MB95100A Series
3
PRODUCT LINEUP
(Continued)
Part number
Parameter
MB95107A
MB95F108AS
MB95F108AW
MB95FV100A-101
Type
MASK product
FLASH product
EVA product
ROM capacity
48 KB
60 KB
RAM capacity
2 KB
3.75 KB
Reset output
No
Option
Selectable
Single/Dual
-system*
2
Single-system
Dual-system
Selectable
Single/Dual
-system*
1
CPU functions
Number of basic instructions
: 136
Instruction bit length
: 8 bits
Instruction length
: 1 to 3 bytes
Data bit length
: 1, 8, and 16 bits
Minimum instruction execution time : 0.1
s (at internal 10 MHz)
Interrupt processing time
: 0.9
s (at internal 10 MHz)
Ports (Max 55 ports)
General-purpose I/O port (Nch open drain)
General-purpose I/O port (CMOS)
: 6 ports
: 49 ports
Timebase timer
Interrupt cycle : 0.5 ms, 2.05 ms, 8.2 ms, 32.8 ms (at main oscillation clock 4 MHz)
Watchdog timer
Reset generated cycle
At main oscillation clock 10 MHz
: Min 105 ms
At sub oscillation clock 32.768 kHz (for dual clock product) : Min 250 ms
Wild register
Capable of replacing 3 bytes of data
I
2
C bus
Master/slave sending and receiving
Bus error function and arbitration function
Detecting transmitting direction function
Start condition repeated generation and detection functions
Built-in wake-up function
UART/SIO
Data transfer capable in UART/SIO
Full duplex double buffer, Variable data length (5/6/7/8-bit), built-in baud rate genera-
tor
Transfer rate : 2400 bps to 125000 bps (at machine clock 10 MHz)
NRZ type transfer format, error detected function
LSB-first or MSB-first can be selected.
Clock synchronous (SIO) or clock asynchronous (UART) data transfer capable
LIN-UART
Dedicated reload timer allowing a wide range of communication speeds to be set.
Capable of data transfer synchronous or asynchronous to clock signal.
LIN functions available as the LIN master or LIN slave.
A/D converter
(12 channels)
8-bit or 10-bit resolution can be selected.
16-bit reload timer
Two clock modes and two counter operating modes can be selected. Square wave-
form output
Count clock : 7 internal clocks and external clock can be selected.
Peripheral functions
MB95100A Series
4
(Continued)
*1 : Change by the switch on MCU board.
*2 : Specify clock mode when ordering MASK ROM.
Part number
Parameter
MB95107A
MB95F108AS
MB95F108AW
MB95FV100A-101
8/16-bit compound tim-
er (2 channels)
Each channel of the timer can be used as "8-bit timer
2 channels" or "16-bit timer
1 channel".
Built-in timer function, PWC function, PWM function, capture function and Square
waveform output
Count clock : 7 internal clocks and external clock can be selected.
16-bit PPG
(2 channels)
PWM mode or one-shot mode can be selected.
Counter operating clock : Eight selectable clock sources
Support for external trigger start
8/16-bit PPG
(2 channels)
Each channel of the PPG can be used as
"
8-bit PPG
2 channels
"
or
"
16-bit PPG
1 channel
"
.
Counter operating clock : Eight selectable clock sources
Watch counter
(for dual clock product)
Count clock : Four selectable clock sources (125 ms, 250 ms, 500 ms, or 1 s)
Counter value can be set from 0 to 63. (Capable of counting for 1 minute)
Watch prescaler
(for dual clock product)
Four selectable interval times (125 ms, 250 ms, 500 ms, or 1 s)
External interrupt
(12 channels)
Interrupt by edge detection (rising, falling, or both edges can be selected.)
Can be used to recover from standby modes.
Standby mode
Sleep, stop, watch, and timebase timer
Peripheral functions
MB95100A Series
5
SELECT OF OSCILLATION STABILIZATION WAIT TIME (MASK PRODUCT ONLY)
For the MASK product, you can set the mask option when ordering MASK ROM to select the initial value of main
clock oscillation stabilization wait time from among the following four values.
Note that the EVA and FLASH products are fixed their initial value of main clock oscillation stabilization wait time
at the maximum value.
PACKAGES AND CORRESPONDING PRODUCTS
: Available
: Unavailable
Oscillation stabilization wait time
Remarks
(2
2
-2) /F
CH
0.5
s (at main oscillation clock 4 MHz)
(2
12
-2) /F
CH
Approx. 1.02 ms (at main oscillation clock 4 MHz)
(2
13
-2) /F
CH
Approx. 2.05 ms (at main oscillation clock 4 MHz)
(2
14
-2) /F
CH
Approx. 4.10 ms (at main oscillation clock 4 MHz)
Part number
Package
MB95107A
MB95F108AS
MB95F108AW
MB95FV100A-101
FPT-64P-M03
FPT-64P-M09
BGA-224P-M08
PDF 
ZIP