1N4001 THRU 1N4007
GENERAL PURPOSE PLASTIC RECTIFIER
Reverse Voltage - 50 to 1000 Volts Forward Current - 1.0 Ampere
FEATURES
The plastic package carries Underwriters Laboratory
Flammability Classification 94V-0
Construction utilizes void-free
molded plastic technique
Low reverse leakage
High forward surge current capability
High temperature soldering guaranteed:
250C/10 seconds, 0.375" (9.5mm) lead length,
5 lbs. (2.3kg) tension
MECHANICAL DATA
Case: JEDEC DO-204AL molded plastic body
Terminals: Plated axial leads, solderable per MIL-STD-750,
Method 2026
Polarity: Color band denotes cathode end
Mounting Position: Any
Weight: 0.012 ounce, 0.3 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25C ambient temperature unless otherwise specified.
1N
1N
1N
1N
1N
1N
1N
SYMBOLS 4001
4002
4003
4004
4005
4006
4007
UNITS
*Maximum repetitive peak reverse voltage
V
RRM
50
100
200
400
600
800
1000
Volts
*Maximum RMS voltage
V
RMS
35
70
140
280
420
560
700
Volts
*Maximum DC blocking voltage
V
DC
50
100
200
400
600
800
1000
Volts
*Maximum average forward rectified current
0.375" (9.5mm) lead length at T
A
=75C
I
(AV)
1.0
Amp
*Peak forward surge current
8.3ms single half sine-wave superimposed on
I
FSM
30.0
Amps
rated load (JEDEC Method) T
A
=75C
*Maximum instantaneous forward voltage at 1.0A
V
F
1.1
Volts
*Maximum full load reverse current
full cycle average 0.375" (9.5mm) lead length at
I
R(AV)
30.0
A
T
L
=75C
*Maximum DC reverse current
T
A
= 25C
5.0
at rated DC blocking voltage
T
A
=100C
I
R
50.0
A
Typical reverse recovery time
(NOTE 1)
t
rr
30.0
s
Typical junction capacitance
(NOTE 2)
C
J
15.0
pF
Typical thermal resistance
(NOTE 3)
R
JA
50.0
R
JL
25.0
C/W
Maximum DC blocking voltage temperature
T
A
+150
C
*Operating junction and storage temperature range
T
J
, T
STG
-50 to +175
C
NOTES:
(1) Measured on Tektronix Type "S" recovery plug-in. Tektronix 545 Scope or equivalent, I
FM
=20mA, I
RM
=1mA
(2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
(3) Thermal resistance from junction to ambient and from junction to lead at 0.375" (9.5mm) lead length, P.C.B. mounted
*JEDEC registered value
4/98
0.107 (2.7)
0.080 (2.0)
0.034 (0.86)
0.028 (0.71)
DIA.
1.0 (25.4)
MIN.
1.0 (25.4)
MIN.
0.205 (5.2)
0.160 (4.1)
DIA.
NOTE:
Lead diameter is for suffix "E" part numbers
0.026 (0.66)
0.023 (0.58)
DO-204AL
Dimensions in inches and (millimeters)
0
25
50
75
100
125
150
175
0
0.2
0.4
0.6
0.8
1.0
1
10
100
5.0
10
15
20
25
30
0.6
0.8
1.0
1.2
1.4
1.6
1.8
0.01
0.1
1
10
20
0.1
1
10
100
1
10
100
0.01
0.1
1
10
100
0.1
1
10
100
0
20
40
60
80
100
0.01
0.1
1
10
100
1,000
RATINGS AND CHARACTERISTIC CURVES 1N4001 THRU 1N4007
FIG.1 - FORWARD CURRENT DERATING CURVE
AMBIENT TEMPERATURE, C
AVERAGE FORWARD
RECTIFIED
CURRENT,
AMPERES
0.375" (9.5mm) LEAD LENGTH
0.2 x 0.2" (5.0 x 5.0mm)
COPPER PADS
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
NUMBER OF CYCLES AT 60 H
Z
PEAK FORWARD SURGE CURRENT,
AMPERES
T
J
=25C
f=1.0 MHz
Vsig=50mVp-p
T
J
=25C
T
J
=100C
T
J
=150C
FIG. 4 - TYPICAL REVERSE CHARACTERISTICS
INSTANTANEOUS FORWARD CURRENT,
AMPERES
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE
t, PULSE DURATION, sec.
TRANSIENT THERMAL IMPEDANCE,
C/W
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
REVERSE VOLTAGE, VOLTS
JUNCTION CAPACITANCE
,
p
F
FIG. 3 - TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS
PERCENTAGE OF PEAK REVERSE VOLTAGE, %
INSTANTANEOUS REVERSE CURRENT
, MICROAMPERES
8.3ms SINGLE HALF SINE WAVE
(JEDEC Method)
T
A
=75C
T
J
=25C
PULSE WIDTH=300
s
1% DUTY CYCLE
60 H
Z
RESISTIVE OR
INDUCTIVE LOAD
PDF 
ZIP