1N4001GP THRU 1N4007GP
GLASS PASSIVATED JUNCTION RECTIFIER
Reverse Voltage - 50 to 1000 Volts Forward Current - 1.0 Ampere
FEATURES
Plastic package has
Underwriters
Laboratory Flammability
Classification 94V-0
High temperature metallurgically
bonded construction
Glass passivated cavity-free junction
Capable of meeting environmental standards of
MIL-S-19500
1.0 Ampere operation at T
A
=75C with no thermal
runaway
Typical I
R
less than 0.1
A
High temperature soldering guaranteed:
350C/10 seconds, 0.375" (9.5mm) lead length,
5 lbs. (2.3kg) tension
MECHANICAL DATA
Case: JEDEC DO-204AL molded plastic over glass body
Terminals: Plated axial leads, solderable per MIL-STD-750,
Method 2026
Polarity: Color band denotes cathode end
Mounting Position: Any
Weight: 0.012 ounce, 0.3 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25C ambient temperature unless otherwise specified.
1N
1N
1N
1N
1N
1N
1N
SYMBOLS
4001GP 4002GP
4003GP
4004GP
4005GP 4006GP
4007GP
UNITS
* Maximum repetitive peak reverse voltage
V
RRM
50
100
200
400
600
800
1000
Volts
* Maximum RMS voltage
V
RMS
35
70
140
280
420
560
700
Volts
* Maximum DC blocking voltage
V
DC
50
100
200
400
600
800
1000
Volts
* Maximum average forward rectified current
0.375" (9.5mm) lead length at T
A
=75C
I
(AV)
1.0
Amp
* Peak forward surge current
8.3ms single half sine-wave superimposed
on rated load (JEDEC Method)
I
FSM
30.0
Amps
Maximum instantaneous forward voltage at 1.0A
V
F
1.1
Volts
* Maximum full load reverse current, full cycle
average 0.375" (9.5mm) lead length T
A
= 75C
I
R(AV)
30.0
A
* Maximum DC reverse current
T
A
=25C 5.0
at rated DC blocking voltage
T
A
=125C
I
R
50.0
A
Typical reverse recovery time
(NOTE 1)
t
rr
2.0
s
Typical junction capacitance
(NOTE 2)
C
J
8.0
pF
Typical thermal resistance
(NOTE 3)
R
JA
55.0
C/W
R
JL
25.0
* Operating junction and storage temperature range
T
J
, T
STG
-65 to +175
C
NOTES:
(1) Reverse recovery test conditions: I
F
=0.5A, I
R
=1.0A, I
rr
= 0.25A
(2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
(3) Thermal resistance from junction to ambient at 0.375" (9.5mm) lead length, P.C.B. mounted
*JEDEC registered values
4/98
0.107 (2.7)
0.080 (2.0)
0.034 (0.86)
0.028 (0.71)
DIA.
1.0 (25.4)
MIN.
1.0 (25.4)
MIN.
0.205 (5.2)
0.160 (4.1)
DIA.
NOTE:
Lead diameter is for suffix "E" part numbers
0.026 (0.66)
0.023 (0.58)
DO-204AL
Dimensions in inches and (millimeters)
*
Glass-plastic encapsulation technique is covered by
Patent No. 3,996,602 and brazed-lead assembly by Patent No. 3,930,306
P
A
TENTED*
25
50
75
100
0.2
0.4
0.6
0.8
1.0
0
10
5.0
10
15
25
100
30
20
1
100
10
20
1
0.1
1
10
0.6
0.8
1.4
1.6
0.01
1
10
0.1
20
1.0
1.2
0
175
125
150
20
40
80
100
0.1
10
0.01
1
0
60
0.01
0.1
1
10
100
0.1
1
10
100
RATINGS AND CHARACTERISTIC CURVES 1N4001GP THRU 1N4007GP
FIG. 1 - FORWARD CURRENT DERATING CURVE
AMBIENT TEMPERATURE, C
A
VERA
GE FOR
W
ARD RECTIFIED CURRENT
,
AMPERES
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
NUMBER OF CYCLES AT 60 H
Z
PEAK FOR
W
ARD SURGE CURRENT
,
AMPERES
FIG. 3 - TYPICAL INSTANTANEOUS
FORWARD CHARACTERISTICS
FIG. 4 - TYPICAL REVERSE CHARACTERISTICS
INST
ANT
ANEOUS FOR
W
ARD CURRENT
, AMPERES
INST
ANT
ANEOUS REVERSE CURRENT
,
MICR
O
AMPERES
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
JUNCTION CAP
A
C
IT
ANCE, pF
REVERSE VOLTAGE, VOLTS
T
J
=T
J
max.
8.3ms SINGLE HALF SINE-WAVE
(JEDEC Method)
T
J
=100C
T
J
=25C
T
J
=25C
PULSE WIDTH=300
s
1% DUTY CYCLE
T
J
=25C
f=1.0 MH
Z
Vsig=50mVp-p
0.375" (9.5mm) LEAD LENGTH
60 H
Z
RESISTIVE OR
INDUCTIVE LOAD
FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE
TRANSIENT
THERMAL IMPED
ANCE (
C/W)
t, PULSE DURATION, sec
PDF 
ZIP