1N5391 THRU 1N5399
GENERAL PURPOSE PLASTIC RECTIFIER
Reverse Voltage - 50 to 1000 Volts Forward Current - 1.5 Amperes
FEATURES
Plastic package has Underwriters Laboratory
Flammability Classification 94V-0
High surge current capability
1.5 Ampere operation at T
L
=70C
with no thermal runaway
Low reverse leakage
Construction utilizes
void-free molded plastic technique
High temperature soldering guaranteed:
250C/10 seconds, 0.375" (9.5mm) lead length,
5 lbs. (2.3kg) tension
MECHANICAL DATA
Case: JEDEC DO-204AL molded plastic body
Terminals: Plated axial leads, solderable per MIL-STD-750,
Method 2026
Polarity: Color band denotes cathode end
Mounting Position: Any
Weight: 0.012 ounce, 0.3 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25C ambient temperature unless otherwise specified.
1N
1N
1N
1N
1N
1N
1N
1N
1N
SYMBOLS
5391
5392
5393
5394 5395 5396 5397
5398 5399
UNITS
*Maximum repetitive peak reverse voltage
V
RRM
50
100
200
300
400
500
600
800 1000
Volts
*Maximum RMS voltage
V
RMS
35
70
140
210
280
350
420
560 700
Volts
*Maximum DC blocking voltage
V
DC
50
100
200
300
400
500
600
800 1000
Volts
*Maximum average forward rectified current
0.500" (12.7mm) lead length at T
L
=70C
I
(AV)
1.5
Amps
*Peak forward surge current
8.3ms single half sine-wave superimposed on
rated load (JEDEC Method) at T
A
=75C
I
FSM
50.0
Amps
*Maximum instantaneous forward voltage
at 1.5A
T
A
=70C
VF
1.4
Volts
*Maximum DC reverse current
T
A
=25C
5.0
at rated DC blocking voltage
T
A
=150C
I
R
300.0
A
*Maximum full load reverse current full cycle
average, 0.375",(9.5mm) lead length at T
L
=70C
I
R(AV)
300.0
A
Typical reverse recovery time
(NOTE 1)
t
rr
2.0
s
Typical junction capacitance
(NOTE 2)
C
J
15.0
pF
Typical thermal resistance
(NOTE 3)
R
JA
50.0
R
JL
25.0
C/W
*Maximum DC blocking voltage temperature
T
A
+150
C
*Operating junction temperature range
T
J
-50 to + 170
C
*Storage temperature range
T
STG
-50 to+175
C
NOTES:
(1) Measured with I
F
=0.5A, I
R
=0.1A, I
rr
= 0.25A
(2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
(3) Thermal resistance from junction to ambient and from junction to lead at 0.375" (9.5mm) lead length, P.C.B. mounted
*JEDEC registered value
4/98
0.107 (2.7)
0.080 (2.0)
0.034 (0.86)
0.028 (0.71)
DIA.
1.0 (25.4)
MIN.
1.0 (25.4)
MIN.
0.205 (5.2)
0.160 (4.1)
DIA.
DO-204AL
Dimensions in inches and (millimeters)
25
50
75
100
125
150
175
0
0.4
0.8
1.2
1.6
2.0
2.4
1
10
0
10
20
30
40
50
100
0.6
0.8
1.0
1.2
1.4
1.6
1.8
0.01
0.1
1
10
100
0.1
1
10
100
1
10
100
0.01
0.1
1
10
100
0.1
1
10
100
0
20
40
60
80
100
0.01
0.1
1
10
100
1,000
RATINGS AND CHARACTERISTIC CURVES 1N5391 THRU 1N5399
FIG. 1 - FORWARD CURRENT DERATING CURVE
LEAD TEMPERATURE, C
AVERAGE FORWARD RECTIFIED CURRENT,
AMPERES
60 H
Z
RESISTIVE OR INDUCTIVE LOAD
0.50" (12.7mm) LEAD LENGTH
FIG. 3 - TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS
INSTANTANEOUS FORWARD CURRENT,
AMPERES
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
T
J
=25C
PULSE WIDTH=300
s
1% DUTY CYCLE
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
NUMBER OF CYCLES AT 60H
Z
PEAK FORWARD SURGE CURRENT,
AMPERES
8.3ms SINGLE HALF SINE WAVE
(JEDEC Method)
T
A
=75C
FIG. 4 - TYPICAL REVERSE CHARACTERISTICS
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
INSTANTANEOUS REVERSE CURRENT,
MICROAMPERES
T
J
=150C
CAPACITIVE LOADS
T
J
=25C
0.2 x 0.2"
(5.0 x 5.0mm)
COPPER PADS
5
10
FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE
t, PULSE DURATION, sec.
TRANSIENT THERMAL IMPEDANCE,
C/W
T
J
=25C
f=1.0 MHz
Vsig=50mVp-p
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
REVERSE VOLTAGE, VOLTS
JUNCTION CAPACITANCE
,
p
F
Ipk/I
AV
=
20
PDF 
ZIP