4/98
2KBP005M THRU 2KBP10M SERIES
3N253 THRU 3N259
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
Reverse Voltage - 50 to 1000 Volts Forward Current - 2.0 Amperes
FEATURES
Plastic package has Underwriters Laboratory Flammability
Classification 94V-0
This series is UL listed under the Recognized Component
Index, file number E54214
Glass passivated chip junctions
Typical I
R
less than 0.1
A
High case dielectric strength
Ideal for printed circuit boards
High temperature soldering guaranteed:
260C/10 seconds at 5 lbs. (2.3kg) tension
MECHANICAL DATA
Case: Molded plastic body over passivated junctions
Terminals: Plated leads solderable per MIL-STD-750,
Method 2026
Mounting Position: Any
Weight: 0.06 ounce, 1.7 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25C ambient temperature unless otherwise specified.
2KBP
2KBP
2KBP
2KBP
2KBP
2KBP
2KBP
005M
01M
02M
04M
06M
08M
10M
SYMBOLS 3N253
3N254
3N255
3N256
3N257
3N258
3N259
UNITS
* Maximum repetitive peak reverse voltage
V
RRM
50
100
200
400
600
800
1000
Volts
* Maximum RMS voltage
V
RMS
35
70
140
280
420
560
700
Volts
* Maximum DC blocking voltage
V
DC
50
100
200
400
600
800
1000
Volts
* Maximum average forward output rectified current
at T
A
=55C
I
(AV)
2.0
Amps
* Peak forward surge current single half sine-wave
superimposed on rated load (JEDEC Method) T
J
=150C
I
FSM
60.0
Amps
Rating for fusing (t < 8.3ms)
I
2
t
15.0
A
2
sec
* Maximum instantaneous forward voltage drop
per leg at 3.14A
V
F
1.1
Volts
* Maximum DC reverse current
T
A
=25C
5.0
at rated DC blocking voltage per leg
T
A
=125C
I
R
500.0
A
Typical junction capacitance per leg
(NOTE 1)
C
J
25.0
pF
Typical thermal resistance per leg
(NOTE 2)
R
JA
30.0
C/W
R
JL
11.0
* Operating junction and storage temperature range
T
J
, T
STG
-55 to +165
C
NOTES:
(1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
(2) Thermal resistance from junction to ambient and from junction to lead mounted on P.C.B. with 0.47 x 0.47" (12 x 12mm) copper pads
* JEDEC registered values
Case Style KBPM
0.125 x 45
o
(3.2)
0.600 (15.24)
0.560 (14.22)
0.034 (8.6)
0.028 (7.6)
0.105 (2.67)
0.085 (2.16)
0.160 (4.1)
0.140 (3.6)
0.060
(1.52)
Polarity shown on front side of case: positive lead by beveled corner
0.460 (11.68)
0.420 (10.67)
0.500 (12.70)
0.460 (11.68)
60
(15.2)
MIN.
0.50
(12.7)
MIN.
DIA.
0.200 (5.08)
0.180 (4.57)
Dimensions in inches and (millimeters)
20
40
60
80
100
120
140
160 170
0
0.5
1.0
1.5
2.0
0.1
1
10
100
1
10
100
1
10
100
0
10
20
30
40
50
60
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
0.01
0.1
1
10
20
0
20
40
60
80
100
0.01
0.1
1
10
100
RATINGS AND CHARACTERISTICS CURVES 3N253 THRU 3N259 / 2KBP005M THRU 2KBP10M
FIG. 1 - DERATING CURVE OUTPUT
RECTIFIED CURRENT
AMBIENT TEMPERATURE, C
60 H
Z
RESISTIVE OR
INDUCTIVE LOAD
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
INSTANTANEOUS REVERSE CURRENT, MICROAM
-
PERES
T
J
=25C
PULSE WIDTH=300
s
1% DUTY CYCLE
FIG. 3 - TYPICAL FORWARD CHARACTERISTICS
PER LEG
INSTANTANEOUS FORWARD CURRENT,
AMPERES
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
PER LEG
REVERSE VOLTAGE, VOLTS
T
J
=25
C
f=1.0 MHz
Vsig=50mVp-p
T
J
=25C
P.C.B.
MOUNTED WITH
0.47 x 0.47"
(12 x 12mm)
COPPER PADS
AVERAGE FORWARD OUTPUT CURRENT,
AMPERES
T
J
=100C
FIG. 4 - TYPICAL REVERSE LEAKAGE
CHARACTERISTICS PER LEG
NUMBER OF CYCLES AT 60 H
Z
PEAK FORWARD SURGE CURRENT,
AMPERES
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT PER LEG
T
J
=125C
T
J
=150C
SINGLE SINE-WAVE
(JEDEC Method)
CAPACITIVE LOAD
Ipk/I
AV
=5.0
Ipk/I
AV
=10
Ipk/I
AV
=20
(PER LEG)
1.0 CYCLE
JUNCTION
CAPACITANCE, pF
PDF 
ZIP