4/98
2W005G THRU 2W10G
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
Reverse Voltage - 50 to 1000 Volts
Forward Current - 2.0 Amperes
FEATURES
Plastic package has Underwriters Laboratory Flammability
Recognition 94V-0
This series is UL listed under the Recognized Component
Index, file number E54214
Glass passivated chip junctions
High case dielectric strength
Typical I
R
less than 0.5
A
High surge current capability
Ideal for printed circuit boards
High temperature soldering guaranteed:
260C for 10 seconds, 0.375" (9.5mm) lead length,
5lbs. (2.3kg) tension
MECHANICAL DATA
Case: Molded plastic body over passivated junctions
Terminals: Plated leads, solderable per MIL-STD-750,
Method 2026
Mounting Position: Any
Weight: 0.04 ounce, 1.1 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25C ambient temperature unless otherwise specified.
2W
2W
2W
2W
2W
2W
2W
SYMBOLS
005G
01G
02G
04G
06G
08G
10G
UNITS
Maximum repetitive peak reverse voltage
V
RRM
50
100
200
400
600
800
1000 Volts
Maximum RMS voltage
V
RMS
35
70
140
280
420
560
700
Volts
Maximum DC blocking voltage
V
DC
50
100
200
400
600
800
1000 Volts
Maximum average forward rectified current
0.375" (9.5mm) lead length
(SEE FIG. 1)
I
(AV)
2.0
Amps
Peak forward surge current single sine-wave
superimposed on rated load (JEDEC Method)
I
FSM
60.0
Amps
Rating for fusing (t<8.3ms)
I
2
t
15.0
A
2
sec
Maximum instantaneous forward voltage drop
per leg at 2.0 Amperes
V
F
1.1
Volts
Maximum DC reverse current at rated
T
A
=25C
5.0
DC blocking voltage per leg
T
A
=125C
I
R
500.0
A
Typical junction capacitance per leg
(NOTE 1)
C
J
40.0
20.0
pF
Typical thermal resistance per leg
(NOTE 2)
R
JA
40.0
C/W
R
JL
15.0
Operating junction temperature range
T
J
-55 to + 150
C
Storage temperature range
T
STG
-55 to +150
C
NOTES:
(1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
(2) Thermal resistance from junction to ambient and from junction to lead at 0.375" (9.5mm) lead length for P.C.B. mounting
Case Style WOG
Dimensions in inches and (millimeters)
0.220 (5.6)
0.160 (4.1)
0.388 (9.86)
0.348 (8.84)
0.032 (0.81)
0.028 (0.71)
1.0
(25.4)
MIN.
0.060 (1.52)
0.020 (0.51)
0.348 (8.84)
0.308 (7.82)
0.220 (5.6)
0.180 (4.6)
0.220 (5.6)
0.180 (4.6)
0
25
50
75
100
125
150
0
0.4
0.8
1.2
1.6
2.0
2.4
100
0.01
0.1
1
10
100
0.1
1
10
0.4
0.6
0.8
1.0
1.2
1.4
1.6
0.01
0.1
1
10
20
100
0.1
1
10
1
10
100
0
10
20
40
50
60
30
100
10
1
0
20
40
60
80
100
0.01
0.1
1
10
100
FIG. 1 - DERATING CURVE OUTPUT
RECTIFIED CURRENT
AMBIENT TEMPERATURE, C
60 H
Z
RESISTIVE OR
INDUCTIVE LOAD
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
INSTANTANEOUS REVERSE CURRENT,
MICROAMPERES
TRANSIENT THERMAL IMPEDANCE,
C/W
T
J
=25C
PULSE WIDTH=300
s
1% DUTY CYCLE
FIG. 3 - TYPICAL FORWARD CHARACTERISTICS
PER LEG
INSTANTANEOUS FORWARD CURRENT,
AMPERES
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
PER LEG
FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE
REVERSE VOLTAGE, VOLTS
t, HEATING TIME, sec.
T
J
=25
C
f=1.0 MHz
Vsig=50mVp-p
T
A
= 25C
CAPACITIVE
LOADS 5.0
Ipk/I
(AV)
10
(PER LEG) 20
COPPER PADS
0.22 x 0.22"
(5.5 x 5.5mm)
AVERAGE FORWARD OUTPUT
CURRENT, AMPERES
T
J
= 125C
FIG. 4 - TYPICAL REVERSE CHARACTERISTICS
PER LEG
T
A
=25C
SINGLE SINE-WAVE
(JEDEC Method)
NUMBER OF CYCLES AT 60 Hz
PEAK FORWARD SURGE CURRENT,
AMPERES
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT PER LEG
T
J
= 100C
P.C.B.
0.375"
(9.5mm)
RATINGS AND CHARACTERISTICS CURVES 2W005G THRU 2W10G
1.0 CYCLE
JUNCTION
CAPACITANCE, pF
PDF 
ZIP