GBPC1005 THRU GBPC110
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
Reverse Voltage - 50 to 1000 Volts Forward Current - 3.0 Amperes
FEATURES
Plastic package has Underwriters Laboratory Flammability
Classification 94V-0
This series is UL listed under Recognized Component Index,
file number E54214
Glass passivated chip junctions
High case dielectric with standing voltage of 1500 V
RMS
Typical I
R
less than 0.1
A
High surge current capability
Ideal for printed circuit boards
High temperature soldering guaranteed:
260C/10 seconds, 0.375" (9.5mm) lead length,
5lbs. (2.3kg) tension
MECHANICAL DATA
Case: Molded plastic body over passivated junctions
Terminals: Plated leads solderable per MIL-STD-750,
Method 2026
Mounting Position: Any
(NOTE 1)
Mounting Torque: 5.0 in. - lb. max.
Weight: 0.1 ounce, 2.8 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25C ambient temperature unless otherwise specified.
GBPC
GBPC
GBPC
GBPC
GBPC
GBPC
GBPC
SYMBOLS 1005
101
102
104
106
108
110
UNITS
Maximum repetitive peak reverse voltage
V
RRM
50
100
200
400
600
800
1000
Volts
Maximum RMS bridge input voltage
V
RMS
35
70
140
280
420
560
700
Volts
Maximum DC blocking voltage
V
DC
50
100
200
400
600
800
1000
Volts
Maximum average forward
T
C
=60C
(NOTE 2)
3.0
rectified output current at
T
A
=25C
(NOTE 3)
I
(AV)
2.0
Amps
Peak forward surge current single sine-wave
superimposed on rated load (JEDEC Method) T
C
=60C
I
FSM
60.0
Amps
Rating for fusing (t<8.3ms)
I
2
t
15.0
A
2
sec
Maximum instantaneous forward voltage drop
per leg at 1.5 Amperes
V
F
1.0
Volts
Maximum DC reverse current at rated
T
A
= 25C
5.0
DC blocking voltage per leg
T
A
=125C
I
R
500.0
A
Typical junction capacitance per leg
(NOTE 4)
C
J
21.0
pF
Typical thermal resistance per leg
(NOTE 2)
R
JA
12.0
R
JC
8.0
C/W
Operating junction and storage temperature range
T
J,
T
STG
-55 to +150
C
NOTES:
(1) Bolt down on heat-sink with silicone thermal compound between bridge and mounting surface for maximum heat transfer with #6 screw
(2) Unit mounted on 4.0 x 4.0 x 0.11" thick (10.5 x 10.5 x 0.3cm) Al. Plate
(3) Unit mounted on P.C.B. at 0.375" (9.5mm) lead length with 0.5 x 0.5" (12 x 12mm) copper pads
(4) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
HOLE FOR
#6 SCREW
0.158 (4.01)
0.142 (3.61)
DIA.
0.128 (3.25)
0.048 (1.22)
0.200 (5.08)
0.160 (4.06)
0.750
(19.05)
MIN.
0.040 (1.02) TYP.
0.094 (2.4) x 45 degrees
0.445 (11.30)
0.405 (10.29)
0.630 (16.00)
0.590 (14.98)
AC
AC
Polarity shown on side of case: Positive lead by beveled corner
0.445 (11.30)
0.405 (10.29)
0.630 (16.00)
0.590 (14.98)
0.032 (0.81)
0.028 (0.71)
DIA.
Case Style GBPC1
Dimensions in inches and (millimeters)
4/98
0
50
100
150
0
1.0
2.0
3.0
4.0
5.0
0.1
1.0
10
100
1
10
100
0.01
0.1
1
10
100
0.1
1
10
100
1
10
100
0
10
20
30
40
50
60
0.4
0.6
0.8
1.0
1.2
1.4
1.6
0.01
0.1
1
10
20
0
20
40
60
80
0.01
0.1
1
10
50
100
RATINGS AND CHARACTERISTICS CURVES GBPC1005 THRU GBPC110
FIG. 1 - DERATING CURVE OUTPUT RECTIFIED
CURRENT
AMBIENT TEMPERATURE, C
AMBIENT TEMPERATURE, T
A
P.C.B. MOUNTING
0.375" (9.5mm) LEAD LENGTH
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
INSTANTANEOUS REVERSE CURRENT,
MICROAMPERES
T
J
=25C
PULSE WIDTH=300
s
1% DUTY CYCLE
FIG. 3 - TYPICAL FORWARD CHARACTERISTICS
PER LEG
INSTANTANEOUS FORWARD CURRENT,
AMPERES
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
PER LEG
REVERSE VOLTAGE, VOLTS
T
J
=25
C
f=1.0 MHz
Vsig=50mVp-p
T
J
=25C
CASE TEMPERATURE,
T
C
HEAT-SINK
MOUNTING,
4.0 x 4.0 x 0.11" THK
(10.5 x 10.5 x 0.3cm)
AL. PLATE
60 H
Z
RESISTIVE OR
INDUCTIVE LOAD
AVERAGE FORWARD OUTPUT
CURRENT, AMPERES
FIG. 4 - TYPICAL REVERSE LEAKAGE
CHARACTERISTICS PER LEG
NUMBER OF CYCLES AT 60 H
Z
PEAK FORWARD SURGE CURRENT,
AMPERES
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT PER LEG
T
J
=125C
FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE
PER LEG
TRANSIENT
THERMAL IMPEDANCE,
C/W
t, HEATING TIME, sec.
T
C
=60C
SINGLE SINE-WAVE
(JEDEC METHOD)
1.0 CYCLE
JUNCTION
CAPACITANCE, pF
PDF 
ZIP