4/98
GI2401 THRU GI2404
GLASS PASSIVATED PLASTIC RECTIFIER
Reverse Voltage - 50 to 200 Volts Forward Current - 16.0 Amperes
FEATURES
Plastic package has Underwriters Laboratory
Flammability Classification 94V-0
Dual rectifier construction, positive centertap
Glass passivated chip junctions
Low power loss
High surge capability
Superfast recovery times for high efficiency
High temperature soldering guaranteed:
250C, 0.16" (4.06mm) from case for 10 seconds
MECHANICAL DATA
Case: JEDEC TO-220AB molded plastic body over
passivated chips
Terminals: Plated lead solderable per MIL-STD-750,
Method 2026
Polarity: As marked
Mounting Position: Any
Mounting Torque: 5 in. - lbs. max.
Weight: 0.08 ounce, 2.24 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25C ambient temperature unless otherwise specified.
.
SYMBOLS
GI2401
GI2402
GI2403
GI2404
UNITS
Maximum recurrent peak reverse voltage
V
RRM
50
100
150
200
Volts
Maximum RMS voltage
V
RMS
35
70
105
140
Volts
Maximum DC blocking voltage
V
DC
50
100
150
200
Volts
Maximum average forward rectified current
at T
C
=125C
I
(AV)
16.0
Amps
Peak forward surge current
8.3ms single half sine-wave superimposed
on rated load (JEDEC Method) at T
C
=125C
I
FSM
125.0
Amps
Maximum instantaneous forward voltage per leg at:
I
F
=4A, T
J
=25C
0.975
I
F
=8A, T
J
=25C
0.900
I
F
=4A, T
J
=100C
0.800
I
F
=8A, T
J
=100C
V
F
0.895
Volts
Maximum DC reverse current
T
C
=25C
50.0 5.0
at rated DC blocking voltage
T
C
=100C
I
R
150.0
500.0
A
Maximum reverse recovery time per leg
(NOTE1)
t
rr
35.0
ns
Typical junction capacitance per leg
(NOTE 2)
C
J
85.0
pF
Typical thermal resistance per leg
(NOTE 3)
R
JA
16.0
C/W
R
JC
2.2
Operating junction and storage temperature range
T
J
, T
STG
-65 to +150
C
NOTES:
(1) Reverse recovery test conditions: I
F
=0.5A, I
R
=1.0A, I
rr
=0.25A
(2) Measured at 1.0 MH
Z
and applied reverse voltage of 4.0 Volts
(3) Thermal resistance from junction to case and from junction to ambient per leg mounted on heatsink
0.415 (10.54) MAX.
0.154 (3.91)
0.148 (3.74)
DIA.
0.113 (2.87)
0.103 (2.62)
0.185 (4.70)
0.175 (4.44)
0.055 (1.39)
0.045 (1.14)
0.145 (3.68)
0.135 (3.43)
0.350 (8.89)
0.330 (8.38)
0.160 (4.06)
0.140 (3.56)
0.037 (0.94)
0.027 (0.68)
0.205 (5.20)
0.195 (4.95)
0.560 (14.22)
0.530 (13.46)
0.022 (0.56)
0.014 (0.35)
0.110 (2.79)
0.100 (2.54)
PIN
1
2
3
PIN 1
PIN 3
CASE
1.148 (29.16)
1.118 (28.40)
0.105 (2.67)
0.095 (2.41)
0.410 (10.41)
0.390 (9.91)
0.105 (2.67)
0.095 (2.41)
0.635 (16.13)
0.625 (15.87)
0.560 (14.22)
0.530 (13.46)
PIN 2
0.370 (9.40)
0.360 (9.14)
TO-220AB
Dimensions in inches and (millimeters)
0.1
1
10
100
10
100
1,000
0
50
100
150
0
4.0
8.0
12
16
20
1
10
100
0
25
50
75
100
125
150
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
0.01
0.1
1
10
80
0
20
40
60
80
100
0.01
0.1
1
10
100
RATINGS AND CHARACTERISTICS CURVES GI2401 THRU GI2404
FIG. 1 -FORWARD CURRENT DERATING CURVE
TEMPERATURE, C
A
VERA
GE FOR
W
ARD CURRENT
,
AMPERES
FIG. 4 - TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS PER LEG
T
J
=25C
PULSE WIDTH=300
s
1% DUTY CYCLE
FIG.3 -TYPICAL REVERSE CHARACTERISTICS
PER LEG
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
INST
ANT
ANEOUS FOR
W
ARD CURRENT
,
AMPERES
8.3ms SINGLE HALF SINE WAVE
(JEDEC Method)
T
C
=125C
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT PER LEG
PEAK FOR
W
ARD SURGE CURRENT
,
AMPERES
REVERSE VOLTAGE, VOLTS
T
J
=25
C
f=1.0 MH
Z
Vsig=50mVp-p
T
J
=125C
NUMBER OF CYCLES AT 60 H
Z
T
J
=125C
INST
ANT
ANEOUS REVERSE LEAKA
GE CURRENT
,
MICR
O
AMPERES
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG
JUNCTION CAP
A
CIT
ANCE, pF
T
J
=25C
T
J
=100C
INFINITE HEAT SINK, T
C
RESISTIVE OR
INDUCTIVE LOAD
AMBIENT AIR RATING, T
A
PDF 
ZIP