4/98
KBP005M THRU KBP10M
3N246 THRU 3N252
GLASS PASSIVATED SINGLE-PHASE RECTIFIER BRIDGE
Reverse Voltage - 50 to 1000 Volts
Forward Current - 1.5 Amperes
FEATURES
Plastic package has Underwriters Laboratory Flammability
Classification 94V-0
This series is UL listed under Recognized Component Index,
file number E54214
Glass passivated chip junctions
High surge current capability
Ideal for printed circuit board
High temperature soldering guaranteed:
260C/10 seconds at 5 lbs. (2.3kg) tension
MECHANICAL DATA
Case: Molded plastic body over passivated junctions
Terminals: Plated lead solderable per MIL-STD-750,
Method 2026
Polarity: Polarity symbols marked on case
Mounting position: Any
Weight: 0.06 ounce, 1.7 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25C ambient temperature unless otherwise specified.
KBP
KBP
KBP
KBP
KBP
KBP
KBP
005M
01M
02M
04M
06M
08M
10M
SYMBOLS 3N246 3N247
3N248
3N249
3N250
3N251
3N252
UNITS
* Maximum repetitive peak reverse voltage
V
RRM
50
100
200
400
600
800
1000
Volts
* Maximum RMS voltage
V
RMS
35
70
140
280
420
560
700
Volts
* Maximum DC blocking voltage
V
DC
50
100
200
400
600
800
1000
Volts
Maximum average forward output rectified current at T
A
=40C
I
(AV)
1.5
Amps
* Peak forward surge current single half sine-wave
50.0
superimposed on rated load (JEDEC Method)
T
J
=150C
I
FSM
30.0
Amps
Rating for fusing (t < 8.3ms)
I
2
t
10.0
A
2
sec
* Maximum instantaneous forward voltage drop
at 1.0A per leg
1.0
1.57A per leg
V
F
1.3
Volts
* Maximum DC reverse current
T
A
=25C
5.0
at rated DC blocking voltage per leg
T
A
=125C
I
R
500.0
A
Typical junction capacitance per leg
(NOTE 1)
C
J
15.0
pF
Typical thermal resistance per leg
(NOTE 2)
R
JA
40.0
R
JL
13.0
C/W
* Operating junction and storage temperature range
T
J
, T
STG
-55 to +150
C
NOTES:
(1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
(2) Thermal resistance from junction to ambient and from junction to lead mounted on P.C.B. with, 0.47 x 0.47" (12 x12mm) copper pads
* JEDEC registered values
Case Style KBPM
0.125 x 45
o
(3.2)
0.600 (15.24)
0.560 (14.22)
0.034 (8.6)
0.028 (7.6)
0.105 (2.67)
0.085 (2.16)
0.160 (4.1)
0.140 (3.6)
0.060
(1.52)
Polarity shown on front side of case: positive lead by beveled corner
0.460 (11.68)
0.420 (10.67)
0.500 (12.70)
0.460 (11.68)
60
(15.2)
MIN.
0.50
(12.7)
MIN.
DIA.
0.200 (5.08)
0.180 (4.57)
Dimensions in inches and (millimeters)
0.1
1
10
100
1
10
100
20
60
80
100
120
140
0
0.2
0.4
0.6
0.8
1.0
40
150
1.2
1.4
1.6
0
10
20
40
50
60
30
100
10
1
0.4
0.6
0.8
1.0
1.2
1.4
1.6
0.01
0.1
1
10
20
0
20
40
60
80
100
0.01
0.1
1
10
RATINGS AND CHARACTERISTICS CURVES KBP005M THRU KBP10M / 3N246 THRU 3N252
FIG.1 - DERATING CURVE OUTPUT
RECTIFIED CURRENT
AMBIENT TEMPERATURE, C
PEAK FORWARD SURGE CURRENT,
AMPERES
60 Hz RESISTIVE OR
INDUCTIVE LOAD
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
INSTANTANEOUS FORWARD VOLTAGE, VOLTS
INSTANTANEOUS REVERSE CURRENT,
MICROAMPERES
T
J
=25C
PULSE WIDTH=300
s
1% DUTY CYCLE
FIG. 3 - TYPICAL FORWARD CHARACTERISTICS
PER LEG
INSTANTANEOUS FORWARD CURRENT,
AMPERES
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
PER LEG
REVERSE VOLTAGE, VOLTS
T
J
=25
C
f=1.0 MHz
Vsig=50mVp-p
T
J
=25C
CAPACITIVE LOAD
Ipk/I
AV
=5.0
Ipk/I
AV
=10
Ipk/I
AV
=20
(PER LEG)
P.C.B.
MOUNTED WITH
0.47 x 0.47"
(12 x 12mm)
COPPER PADS
BRIDGE OUTPUT
FULL WAVE RECTIFIED CURRENT,
AVERAGE AMPERES
NUMBER OF CYCLES AT 60 H
Z
T
J
=100C
FIG. 4 - TYPICAL REVERSE LEAKAGE
CHARACTERISTICS PER LEG
SINGLE SINE-WAVE
(JEDEC Method)
T
A
=25C
T
J
=150C
T
J
=125C
JUNCTION
CAPACITANCE, pF
1.0 CYCLE
PDF 
ZIP