10/1/98
UG10FCT AND UG10GCT
ULTRAFAST SOFT RECOVERY RECTIFIER
Reverse Voltage - 400 Volts Forward Current - 10.0 Amperes
FEATURES
Plastic package has Underwriters Laboratories
Flammability Classification 94V-0
Ideally suited for free wheeling diode power factor
correction applications
Soft recovery characteristics
Excellent high temperature switching
Optimized to reduce switching losses
High temperature soldering guaranteed:
250C/10 seconds at terminals
Glass passivated chip junction
MECHANICAL DATA
Case: JEDEC TO-220AB molded plastic body
Terminals: Plated leads, solderable per MIL-STD-750,
Method 2026
Polarity: As marked
Mounting Position: Any
Mounting Torque: 5 in. - lbs. max.
Weight: 0.08 ounce, 2.24 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25C ambient temperature unless otherwise specified.
SYMBOLS
UG10FCT
UG10GCT
UNITS
Maximum repetitive peak reverse voltage
V
RRM
300
400
Volts
Working peak reverse voltage
V
RWM
225
300
Volts
Maximum RMS voltage
V
RMS
210
280
Volts
Maximum DC blocking voltage
V
DC
300
400
Volts
Maximum average forward rectified current at T
C
=100C
I
(AV)
10
Amps
Peak forward surge current
8.3ms single half sine-wave superimposed
I
FSM
60A
Amps
on rated load (JEDEC Method) per leg
Maximum instantaneous forward voltage per leg
T
J
=25C
1.30
Volts
(NOTE 1)
I
F
= 5A
T
J
=150C
V
F
1.05
Maximum reverse leakage current
T
J
=25C
10
at working peak reverse voltage
T
J
=100C
I
R
200
A
Maximum reverse recovery time per leg at I
F
=0.5A, I
R
=1.0A, I
rr
=0.25A
t
rr
35
ns
Maximum Reverse recovery time per leg at
I
F
=1.0A, di/dt=100A/
s, V
R
=30V, I
rr
=0.1 I
RM
t
rr
50
ns
Maximum reverse recovery current per leg at
I
F
=5A, di/dt=50A/
s,V
R
=30V
T
C
=100C
I
RM
3.0
Amps
Maximum stored charge per leg
I
F
=2A, di/dt=20A/
s, V
R
=30V, I
rr
=0.1 I
RM
Q
rr
50
nC
Typical thermal resistance from junction to case per leg
R
JC
4.5
C/W
Operating junction and storage temperature range
T
J
, T
STG
-40 to +150
C
NOTE: (1) Pulse test: 300
s pulse width, 1% duty cycle
NOTICE: Advanced product information is subject to change without notice
0.415 (10.54) MAX.
0.154 (3.91)
0.148 (3.74)
DIA.
0.113 (2.87)
0.103 (2.62)
0.185 (4.70)
0.175 (4.44)
0.055 (1.39)
0.045 (1.14)
0.145 (3.68)
0.135 (3.43)
0.350 (8.89)
0.330 (8.38)
0.160 (4.06)
0.140 (3.56)
0.037 (0.94)
0.027 (0.68)
0.205 (5.20)
0.195 (4.95)
0.560 (14.22)
0.530 (13.46)
0.022 (0.56)
0.014 (0.35)
0.110 (2.79)
0.100 (2.54)
PIN
1
2
3
PIN 1
PIN 3
CASE
1.148 (29.16)
1.118 (28.40)
0.105 (2.67)
0.095 (2.41)
0.410 (10.41)
0.390 (9.91)
0.105 (2.67)
0.095 (2.41)
0.635 (16.13)
0.625 (15.87)
0.560 (14.22)
0.530 (13.46)
PIN 2
0.370 (9.40)
0.360 (9.14)
TO-220AB
Dimensions in inches and (millimeters)
NEW PRODUCT
NEW PRODUCT
NEW PRODUCT
0
25
50
75
100
125
150
0
5
10
15
1
10
100
1
10
100
0.1
1
10
100
1,000
1
10
100
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
0.01
0.1
1
10
100
25
50
75
100
125
0
50
100
150
200
250
300
20
40
60
80
100
0.1
1
10
100
1,000
FIG. 1 -FORWARD CURRENT DERATING CURVE
CASE TEMPERATURE, C
A
VERAGE FOR
W
ARD CURRENT
,
AMPERES
FIG. 3 - TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS PER LEG
T
J
=25C
PULSE WIDTH=300
s
1% DUTY CYCLE
FIG. 4 - TYPICAL REVERSE CHARACTERISTICS
PER LEG
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
INST
ANT
ANEOUS FOR
W
ARD CURRENT
,
AMPERES
8.3ms SINGLE HALF SINE-WAVE
(JEDEC Method)
T
C
=105
C
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT PER LEG
PEAK FOR
W
ARD SURGE CURRENT
,
AMPERES
REVERSE VOLTAGE, VOLTS
T
J
=125
C
f=1.0 MHz
Vsig=50MVp-p
NUMBER OF CYCLES AT 60 H
Z
INST
ANT
ANEOUS REVERSE LEAKAGE CURRENT
,
MICROAMPERES
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
FIG. 6 - TYPICAL JUNCTION CAPACITANCE PER LEG
FIG. 5 - REVERSE SWITCHING CHARACTERISTICS
PER LEG
CAP
ACIT
ANCE, pF
RESISTIVE OR INDUCTIVE LOAD
RATINGS AND CHARACTERISTIC CURVES UG10FCT AND UG10GCT
T
J
=125
C
T
J
=125
C
T
J
=100
C
T
J
=100
C
T
J
=25
C
T
J
=25
C
t
rr
Q
rr
JUNCTION TEMPERATURE, C
@2A, 20A/
s
@5A, 50A/
s
@5A, 50A/
s
@1A, 100A/
s
@2A, 20A/
s
ST
ORED CHARGE/REVERSE RECOVER
Y
TIME,
nC/ns
PDF 
ZIP