ChipFind - документация

Электронный компонент: DOM40MV016

Скачать:  PDF   ZIP
HANBit HFDOM40MVxxx
URL:www.hbe.co.kr 1 / 1 HANBit Electronics Co., Ltd.
Rev. 1.0 (January. 2004)


1. PRODUCT OVERVIEW
GENERAL DESCRIPTION
The HFDOM40MVxxx series 40Pin Flash Disk Module is a flash technology based with True IDE interface flash memory
card. It is constructed with flash disk controller chip and NAND-type (Samsung) flash memory device. The HFDOM40MV-
xxx series operates in both 3.3-Volt and 5.0-Volt power supplies. It comes in capacity of 16, 32, 64, 128, 192, 256, 384,
512 MB and up to 768B MB formatted 40Pin type .
By optimizing flash memory management, the life of this HFDOM40MVxxx series can be extended to its maximum level.
Because the ECC function is included, the correctness of data transfer between the HFDOM40MVxxx series and a True
IDE compatible interface device can be guaranteed.
The HFDOM40MVxxx series is fully compatible with applications such as CPU card / board, set top box, industry /
military PC / Notebook, security equipment, measuring instrument and embedded systems.

FEATURES
-
ATA / True IDE compatible host interface
-
ATA command set compatible
-
Automatic sensing of PC Card ATA or true IDE host interface.
-
Very high performance, low power consumption
-
Automatic error detection and error correction
-
Auto Standby to save power consumption.
-
Supports automatic power down and wake up
-
Support for 8 or 16 bit host transfers
-
3.3V/5.0V operation voltage
-
Host Interface bus width : 8/16 bit Access
-
Flash Interface bus width : 8 bit Access
-
Capacity : Min. 16MB ~ Max. 768MB
PRODUCT SPECIFICATIONS
Capacities :
16, 32, 64, 96, 128, 192, 256, 384, 512 and up to 768MB (formatted)
System Compatibility :
Please refer to the compatibility list of index.
Performance :
Host Data Transfer Rates :
up to 16.6 MB/sec, PIO mode 4; 16.6MB/sec, Multi-word
DMA mode 2; 33MB/sec





40Pin Disk On Module Min.16MB ~ Max.768MB, True IDE Interface
Mode, 3.3V / 5.0V Operating Part No
. HFDOM40MVxxx
HANBit HFDOM40MVxxx
URL:www.hbe.co.kr 2 / 2 HANBit Electronics Co., Ltd.
Rev. 1.0 (January. 2004)
Reliability :
MTBF
:
xxx,xxx
hours
ECC
:
Embedded
ECC
Function
Data Retention
: 10 years
Operating Voltage : 3.3V / 5.0V 10%

Power consumption : 3.3V
5%
Read mode
<40 mA
Write mode
<60 mA
Stop mode
<2 mA
Environment conditions :
Operating temperature
0C to + 65C
Storage temperature
- C to + C
Relative humidity
8% to 95%, non-condensing

ELECTRICAL SPECIFICATIONS
Table 1.1 Absolute Maximum Ratings
Symbol Parameter
Rating
Units
V
DD
Power supply
-0.3 to 6.0
V
V
IN
Input voltage
-0.3 to V
DD
+0.3 V
V
OUT
Output voltage
-0.3 to V
DD
+0.3 V
T
STG
Storage temperature
-25 to 125
o
C
Table 1.2 Recommended Operating Conditions
Symbol Parameter Min.
Max. Units
V
DD
Power
supply
3.0
5.5
V
V
IN
Input
voltage
0
V
DD
V
T
OPR
Operating
temperature 0 65
o
C
Table 1.3 DC Characteristics
Sym. Parameter
Min
Typ
Max
Units
V
IL
Input low voltage
0.6
V
V
IH
Input high voltage
2.4
V
V
IL
Schmitt input low voltage
1.0
V
V
IH
Schmitt input high voltage
1.8
V
V
OL
Output low voltage
0.4
V
V
OH
Output high voltage
2.5
V
R
I
Input pull up/down resistance
50
k


HANBit HFDOM40MVxxx
URL:www.hbe.co.kr 3 / 3 HANBit Electronics Co., Ltd.
Rev. 1.0 (January. 2004)
INSTALLTION GUIDE
1) Setting Method
Make sure your computer is turned off before you open the case.
Plug the carefully into the 40pin IDE slot on your computer.
Caution: Make sure to align pin1 on host adapter interface connector with pin 1 on your Flash Disk Module. Pin 1
is indicated by a triangle on the Flash Disk Module connector.
The Flash Disk Module is used power connector cable of the computer.
Caution: If you need to remove your Flash Disk Module, use both hands to pull it out carefully.
Check all cable connections and then replace your computer cover.
2) BIOS setting Method
Before you format or partition your new drive, you must configure your computer's BIOS so that the computer can
recognize your new drive.
Turn your computer on. As your computer start up, watch the screen for a message describing how to run the
system setup program on the screen (sometimes called BIOS or CMOS setup). This is usually done by pressing a
special key, such as Delete, Esc or F1 during startup. See your computer manual for details. Press the appropriate
key to run the system setup program.
If your BIOS provides automatic drive detection (an "AUTO" drive type), select this option. ( We
recommend to use Normal / CHS mode to partition your Flash Disk Module to get the maximum formatted
capacity.
)
This allows your computer to configure itself automatically for your new drive.
If your BIOS dose not provide "AUTO" drive detection, select "User-defined" drive setting and enter the
CHS values from the table.
BIOS Settings (see specification) Capacity Cylinders Heads Sectors(unformatted)
Save the settings and exit the System Setup program. ( your computer will automatically reboot ) After you
configure your computer, you can use the standard DOS commands to partition and format your Flash Disk Module,
as described below.
3)
Formatting Method
To partition your new Flash Disk Module with Microsoft DOS program :
Insert a bootable DOS diskette into your diskette drive and restart your computer.
Insert a DOS program diskette that contains the FDISK.EXE and FORMAT.COM
programs into your diskette drive. Use the same DOS version that is on your bootable diskette. At the A:\ > prompt,
type "FDISK" and press Enter.
Select "Create DOS partition or logical DOS drive" by pressing 1. Then press Enter.
Select "Create primary DOS partition" by pressing 1 again. Then press Enter.
Create your first drive partition. If you are creating a partition that will be used to boot your computer (drive C),
make sure that the partition is marked active.
Create an extended partition and additional logical drives as necessary, until all the space on your new hard drive
has been partitioned.
When the partitioning is complete, FDISK reboots your computer.
Caution: Make sure to use the correct drive letters so that you do not format a drive that already contains data.
At the A:\ > prompt, type "format c:/s", where c is the letter of your first new partition, Repeat the format process
for all the new partitions you have created.
After you format your drive, it is ready to use.







HANBit HFDOM40MVxxx
URL:www.hbe.co.kr 4 / 4 HANBit Electronics Co., Ltd.
Rev. 1.0 (January. 2004)
2. PIN INFORMATION
PIN ASSIGNMENTS AND PIN TYPE
Table 2.1 Pin Assignment and Pin type
Pin Signal
Pin
Type
Pin Signal
Pin
Type
1
/RESET I
2
GND Ground
3
D07 I/O 4
D08 I/O
5
D06 I/O 6
D09 I/O
7
D05 I/O 8
D10 I/O
9
D04 I/O 10
D11 I/O
11
D03 I/O 12
D12 I/O
13
D02 I/O 14
D13 I/O
15
D01 I/O 16
D14 I/O
17
D00 I/O 18
D15 I/O
19
GND DC 20
Key Pin
--
21
INPACK --
22
GND Ground
23
/IOW I 24
GND Ground
25
/IOR I 26
GND Ground
27
IORDY O 28
Reserved --
29
REG -- 30
GND Ground
31
IRQ O 32
/IOIS16 O
33
A01 I 34
/PDIAG I/O
35
A00 I 36
A02 I
37
/CS0 I 38
/CS1 I
39
/DASP I/O 40
GND Ground









HANBit HFDOM40MVxxx
URL:www.hbe.co.kr 5 / 5 HANBit Electronics Co., Ltd.
Rev. 1.0 (January. 2004)
Signal Descriptions
Table 2.2 Signal Descriptions
Signal Name
Dir.
Pin
Description
A[2:0]
I 33,35,36
In True IDE Mode only A[2:0] are used to select the one of eight registers in
the Task File, the remaining address lines should be grounded by the host.
-PDIAG
I/O
34
This input / output is the Pass Diagnostic signal in the Master / Slave
handshake protocol.
-DASP
I/O
39
In the True IDE Mode, this input/output is the Disk Active/Slave
Present signal in the Master/Slave handshake protocol.
-CS0, -CS1
I 37,38
CS0 is the chip select for the task file registers while CS2 is used to select
the Alternate Status Register and the Device Control Register.
D[15:00]
I/O
3,4,5,6,
7,8,9,10,
11,12,13,
14,15,16,
17,18
All Task File operations occur in byte mode on the low order bus D00-D07
while all data transfers are 16 bit using D00-D15.
GND
--
2,19,22,
24,26,
30,40,
Ground.
-IOR
I 25
This is an I/O Read strobe generated by the host.
-IOW
I 23
The I/O Write strobe pulse is used to clock I/O data on the Card Data bus
into the Storage Card controller registers when the Storage Card is
configured to use the I/O interface. The clocking will occur on the negative to
positive edge of the signal (trailing edge).
IRQ
O 31
In True IDE Mode signal is the active high Interrupt Request to the host.
-RESET
I 1
This input pin is the active low hardware reset from the host.
IORDY
O 27
This output signal may be used as IORDY.
-IOIS16
O 32
This output signal is asserted low when this device is expecting a word data
transfer cycle.