ChipFind - документация

Электронный компонент: DOM44KR01G

Скачать:  PDF   ZIP
HANBit HFDOM44KRxxx
URL:www.hbe.co.kr 1 / 30 HANBit Electronics Co., Ltd.
Rev. 1.0 (December, 2004)


1. PRODUCT OVERVIEW
GENERAL DESCRIPTION
The HFDOM44KRxxx series 44Pin Flash Disk Module is a flash technology based with True IDE interface flash memory
card. It is constructed with flash disk controller chip and NAND-type (Samsung) flash memory device. The HFDOM44KR-
xxx series operates in both 3.3-Volt and 5.0-Volt power supplies. It comes in capacity of 16, 32, 64, 128, 192, 256, 512 MB
and up to 1GB MB formatted 44Pin type .
By optimizing flash memory management, the life of this HFDOM44KRxxx series can be extended to its maximum level.
Because the ECC function is included, the correctness of data transfer between the HFDOM44KRxxx series and a True
IDE compatible interface device can be guaranteed.
The HFDOM44KRxxx series is fully compatible with applications such as CPU card / board, set top box, industry /
military PC / Notebook, security equipment, measuring instrument and embedded systems.

FEATURES
-
ATA / True IDE compatible host interface
-
ATA command set compatible
-
Automatic sensing of PC Card ATA or true IDE host interface.
-
Very high performance, very low power consumption
-
Automatic error correction
-
Auto Standby to save power consumption.
-
Supports power down commands and sleep modes.
-
Integrated PCMCIA attribute memory of 256 bytes (CIS)
-
Support for 8 or 16 bit host transfers
-
3.3V/5.0V operation voltage
-
Host Interface bus width : 8/16 bit Access
-
Flash Interface bus width : 8 bit Access
-
Capacity : Min. 16MB ~ Max. 1GMB
-
MTBF > 1,000,000 hours.
-
Minimum 10,000 insertions.
-
Shock : 2,000 G max.
-
Vibration : 15 G peak to peak max.
PRODUCT SPECIFICATIONS
Capacities :
16, 32, 48, 64, 96, 128, 192, 256, 512 and up to 1GB (formatted)
System Compatibility :
Please refer to the compatibility list of index.
Performance :
Host Data Transfer Rates :
up to 16.6 MB/sec, PIO mode 4; 16.6MB/sec, Multi-word


40Pin Flash Disk Module Min.8MB ~ Max.1GB, True IDE Interface
Mode, 3.3V / 5.0V Operating Part No
. HFDOM44KRxxx
HANBit HFDOM44KRxxx
URL:www.hbe.co.kr 2 / 30 HANBit Electronics Co., Ltd.
Rev. 1.0 (December, 2004)
Operating Voltage : 3.3V / 5.0V 10%

Power consumption : 3.3V
5%
Read mode
<30 mA
Write mode
<56 mA
Stop mode
<2 mA
Environment conditions :
Operating temperature
0C to + 65C
Storage temperature
- C to + C
Relative humidity
8% to 95%, non-condensing

ELECTRICAL SPECIFICATIONS
Table 1.1 Absolute Maximum Ratings
Symbol Parameter
Rating
Units
V
DD
Power supply
-0.3 to 6.0
V
V
IN
Input voltage
-0.3 to V
DD
+0.3 V
V
OUT
Output voltage
-0.3 to V
DD
+0.3 V
T
STG
Storage temperature
-25 to 125
o
C
Table 1.2 Recommended Operating Conditions
Symbol Parameter Min.
Max. Units
V
DD
Power
supply
3.0
5.5
V
V
IN
Input
voltage
0
V
DD
V
T
OPR
Operating
temperature 0 65
o
C
Table 1.3 DC Characteristics
Sym. Parameter
Min
Typ
Max
Units
V
IL
Input low voltage
0.3V
DD
V
V
IH
Input high voltage
0.7V
DD
V
V
IL
Schmitt input low voltage
1.22
V
V
IH
Schmitt input high voltage
2.08
V
V
OL
Output low voltage
0.4
V
V
OH
Output high voltage
2.3
1
V
R
I
Input pull up/down resistance
75
k








HANBit HFDOM44KRxxx
URL:www.hbe.co.kr 3 / 30 HANBit Electronics Co., Ltd.
Rev. 1.0 (December, 2004)
CAPACITY SPECIFICATIONS
Table 1.4 Capacity Specifications
Part Number
Capacity (formatted)
Cylinders Heads Sectors
NOTE
HFDOM44KR016
15,32Mbytes
984 16 2
HFDOM44KR032
30,65 Mbytes
984 16 4
HFDOM44KR064
61,32 Mbytes
984 16 8
HFDOM44KR096
91,98 Mbytes
984 16 12
122,64 Mbytes
984 16 16
HFDOM44KR128
119,65 Mbytes
960 16 16
K9K1G08UOM
HFDOM44KR192
183,96 Mbytes
984 16 24
245,28 Mbytes
984 16 32
HFDOM44KR256
239,29 Mbytes
960 16 32
K9K1G08UOM
369,91 Mbytes
984 16 48
HFDOM44KR384
357,86 Mbytes
960 16 48
K9K1G08UOM
490,28 Mbytes
999 16 63
HFDOM44KR512
478,59 Mbytes
975 16 63
K9K1G08UOM
HFDOM44KR01G
981,00 Mbytes
1999 16 63


















HANBit HFDOM44KRxxx
URL:www.hbe.co.kr 4 / 30 HANBit Electronics Co., Ltd.
Rev. 1.0 (December, 2004)
PHYSYCAL SPECIFICATION
2.70.1
Jumper 31.00.5mm
1.70.08mm
48.40.1mm
52.30.3mm
< View from connector side >
6.30.2mm
< View from Right side >
Jumper
Master Slave
1,2
Close
2,3
Close
2
1
3
2
1
HANBit HFDOM44KRxxx
URL:www.hbe.co.kr 5 / 30 HANBit Electronics Co., Ltd.
Rev. 1.0 (December, 2004)
INSTALLTION GUIDE
1) Setting Method
Make sure your computer is turned off before you open the case.
Plug the carefully into the 40pin IDE slot on your computer.
Caution: Make sure to align pin1 on host adapter interface connector with pin 1 on your Flash Disk Module. Pin 1
is indicated by a triangle on the Flash Disk Module connector.
The Flash Disk Module is used power connector cable of the computer.
Caution: If you need to remove your Flash Disk Module, use both hands to pull it out carefully.
Check all cable connections and then replace your computer cover.
2) BIOS setting Method
Before you format or partition your new drive, you must configure your computer's BIOS so that the computer can
recognize your new drive.
Turn your computer on. As your computer start up, watch the screen for a message describing how to run the
system setup program on the screen (sometimes called BIOS or CMOS setup). This is usually done by pressing a
special key, such as Delete, Esc or F1 during startup. See your computer manual for details. Press the appropriate
key to run the system setup program.
If your BIOS provides automatic drive detection (an "AUTO" drive type), select this option. ( We
recommend to use Normal / CHS mode to partition your Flash Disk Module to get the maximum formatted
capacity.
)
This allows your computer to configure itself automatically for your new drive.
If your BIOS dose not provide "AUTO" drive detection, select "User-defined" drive setting and enter the
CHS values from the table.
BIOS Settings (see specification) Capacity Cylinders Heads Sectors(unformatted)
Save the settings and exit the System Setup program. ( your computer will automatically reboot ) After you
configure your computer, you can use the standard DOS commands to partition and format your Flash Disk Module,
as described below.
3)
Formatting Method
To partition your new Flash Disk Module with Microsoft DOS program :
Insert a bootable DOS diskette into your diskette drive and restart your computer.
Insert a DOS program diskette that contains the FDISK.EXE and FORMAT.COM
programs into your diskette drive. Use the same DOS version that is on your bootable diskette. At the A:\ > prompt,
type "FDISK" and press Enter.
Select "Create DOS partition or logical DOS drive" by pressing 1. Then press Enter.
Select "Create primary DOS partition" by pressing 1 again. Then press Enter.
Create your first drive partition. If you are creating a partition that will be used to boot your computer (drive C),
make sure that the partition is marked active.
Create an extended partition and additional logical drives as necessary, until all the space on your new hard drive
has been partitioned.
When the partitioning is complete, FDISK reboots your computer.
Caution: Make sure to use the correct drive letters so that you do not format a drive that already contains data.
At the A:\ > prompt, type "format c:/s", where c is the letter of your first new partition, Repeat the format process
for all the new partitions you have created.
After you format your drive, it is ready to use.