ChipFind - документация

Электронный компонент: HFDOM-40LX256

Скачать:  PDF   ZIP
HANBit HFDOM-40LX Series
URL : www.hbe.co.kr 1 / 1 HANBit Electronics Co., Ltd
.
REV 1.0 (February, 2003.)


GENERAL DESCRIPTION
The HFDOM40LX series 40Pin Flash Disk on Module is a flash technology based with True IDE interface flash memory
card for Lexar controller. It is constructed with flash disk controller chip and NAND-type (Samsung) flash memory device.
The HFDOM40LX series operates in 5.0-Volt power supplies. It comes in capacity of 128, 192MB and up to 256 MB
formatted 40Pin type .
By optimizing flash memory management, the life of this HFDOM40LX series can be extended to its maximum level.
Because the ECC function is included, the correctness of data transfer between the HFDOM40LX series and a True IDE
compatible interface device can be guaranteed.
The HFDOM40LX series is fully compatible with applications such as CPU card / board, set top box, industry / military PC,
security equipment, measuring instrument and embedded systems.
FEATURES
-
True IDE compatible host interface
-
Direct plug in for 3.5
IDE Connectors
-
40 pin 2.54mm IDE Connector
-
Ultra-High Performance
-
Support for CIS implemented with 256 bytes of attribute memory
-
5.0V operation voltage
-
Burst Rate (to/from Host): up to 16.6MB/s (PIO mode 4)
-
Sustained Write (Host to flash): minimum of 1.2MB/s
-
Data Transfer Rate (device to PC via USB interface): up to 850KB/s
-
Capacity : Min. 128MB ~ Max. 256MB
-
Auto Sleep Mode
-
Low Power Dissipation
-
Low VCC Program Inhibit Function


PRODUCT SPECIFICATIONS
Capacities :
128, 192 and up to 256 MB (formatted)
Operating Voltage :
5.0V 10%
Power consumptions :
Read mode
65 mA (typ)
Write mode
65 mA (typ)
Sleep mode
300 uA (typ)
Environment conditions :
Operating temperature
0C to + 70C
Storage temperature
- 25C to + 85C
Relative humidity
95%(Max)
Mechanical conditions :
Weight : Maximum 9.0g


40Pin Flash Disk Module for 128MB,192M, 256M, True IDE Interface
Mode, 5.0V Part No
. HFDOM40LX-xxxx
HANBit HFDOM-40LX Series
URL : www.hbe.co.kr 2 / 2 HANBit Electronics Co., Ltd
.
REV 1.0 (February, 2003.)
ELECTRICAL SPECIFICATIONS
Table 1.1 Absolute Maximum Ratings
Parameters Symbol
Min
Max
Unit
Test
Condition
Storage Temperature
Tstg
-65
150
C
Power Supply Voltage
Vcc
-0.3
7
V
Input or Output Voltage
Vin, Vout
Gnd-0.5
Vcc+0.5
V
NOTE :Stress above those listed under Absolute Maximum Ratings may cause permanent
damage to the device. This is a stress rating only and functional operation of the
device at these or any conditions above those indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum rating conditions for extended periods may affect device
reliability.
Table 1.2 Recommended Operating Conditions
Parameters Symbol
Min
Max
Unit
Test
Condition
Operating Temperature
Ta
0
70
C
Supply Voltage
Vcc
4.5
5.5
V
Table 1.3 DC Characteristics
(Ta = 0 to +70C, Vcc = 5V
10%, Vcc = 3V
5%)
Parameters Symbol
Min
Max
Unit
Test
Condition
Power Supply voltage
Vdd
3.15
5.5
V
Input Low Voltage
Vil
-0.5
0.8
V
Input High Voltage
Vih 2.0
Vdd+0.3
V
Output Low Voltage
Vol
-
0.4
V
Output High Voltage
Voh
2.4
-
V
Input Leakage
Il
-5
5
uA
Output Capacitance
Cout
-
10
pF
Read Current
Irc
55
mA
Write Current
Iwr
55
mA
Sleep Current
Isc
200
uA



CAPACITY SPECIFICATIONS
Table 1.4 Capacity Specifications
Part Number
Capacity (Unformatted)
Sectors/Card
Cylinders
Heads Sectors/Track
HFDOM-40LX128
128,188,416
bytes
250,368
978
8
32
HFDOM-40LX192
193,462,272
bytes
377,856
738
16
32
HFDOM-40LX256
257,949,696
bytes
503,808
984
16
32


HANBit HFDOM-40LX Series
URL : www.hbe.co.kr 3 / 3 HANBit Electronics Co., Ltd
.
REV 1.0 (February, 2003.)
1
2
3
+
-
Jumper
1
PHYSYCAL SPECIFICATIONS
51.700.1mm
22.100.1mm
29.100.2mm
7.00.1mm



55.370.1mm
< View from front side >
3.80.1mm
2.540.05mm
6.00.1mm
2.540.05mm
48.200.1mm
55.300.1mm
< View from connector side >
Figure 1.1 40 pin Type Flash Disk Module Dimensions



INSTALLTION GUIDE
Jumper
Slave
Master
1,2
Close
2,3
Close
POWER
HANBit HFDOM-40LX Series
URL : www.hbe.co.kr 4 / 4 HANBit Electronics Co., Ltd
.
REV 1.0 (February, 2003.)
1) Setting Method
(for example)
Make sure your computer is turned off before you open the case.
Plug the carefully into the 40pin IDE slot on your computer.
Caution: Make sure to align pin1 on host adapter interface connector with pin 1 on your Flash Disk Module. Pin 1
is indicated by a triangle on the Flash Disk Module connector.
The Flash Disk Module is used power connector cable of the computer.
Caution: If you need to remove your Flash Disk Module, use both hands to pull it out carefully.
Check all cable connections and then replace your computer cover.
2) BIOS setting Method
(for example)
Before you format or partition your new drive, you must configure your computer's BIOS so that the computer can
recognize your new drive.
Turn your computer on. As your computer start up, watch the screen for a message describing how to run the
system setup program on the screen (sometimes called BIOS or CMOS setup). This is usually done by pressing a
special key, such as Delete, Esc or F1 during startup. See your computer manual for details. Press the appropriate
key to run the system setup program.
If your BIOS provides automatic drive detection (an "AUTO" drive type), select this option. ( We
recommend to use Normal / CHS mode to partition your Flash Disk Module to get the maximum formatted
capacity.
)
This allows your computer to configure itself automatically for your new drive.
If your BIOS dose not provide "AUTO" drive detection, select "User-defined" drive setting and enter the
CHS values from the table.
BIOS Settings (see specification) Capacity Cylinders Heads Sectors(unformatted)
Save the settings and exit the System Setup program. ( your computer will automatically reboot ) After you
configure your computer, you can use the standard DOS commands to partition and format your Flash Disk Module,
as described below.
3)
Formatting Method
(for example)
To partition your new Flash Disk Module with Microsoft DOS program :
Insert a bootable DOS diskette into your diskette drive and restart your computer.
Insert a DOS program diskette that contains the FDISK.EXE and FORMAT.COM
programs into your diskette drive. Use the same DOS version that is on your bootable diskette. At the A:\ > prompt,
type "FDISK" and press Enter.
Select "Create DOS partition or logical DOS drive" by pressing 1. Then press Enter.
Select "Create primary DOS partition" by pressing 1 again. Then press Enter.
Create your first drive partition. If you are creating a partition that will be used to boot your computer (drive C),
make sure that the partition is marked active.
Create an extended partition and additional logical drives as necessary, until all the space on your new hard drive
has been partitioned.
When the partitioning is complete, FDISK reboots your computer.
Caution: Make sure to use the correct drive letters so that you do not format a drive that already contains data.
At the A:\ > prompt, type "format c:/s", where c is HFDOM40LX, Repeat the format process for all the new
partitions you have created.
After you format your drive, it is ready to use.
1. PIN INFORMATION
HANBit HFDOM-40LX Series
URL : www.hbe.co.kr 5 / 5 HANBit Electronics Co., Ltd
.
REV 1.0 (February, 2003.)
PIN ASSIGNMENTS AND PIN TYPE
Table 2.1 Pin Assignment and Pin type
Pin Signal
Pin
Type
Pin Signal
Pin
Type
1
/RESET I
2
GND GND
3
D07 I/O 4
D08 I/O
5
D06 I/O 6
D09 I/O
7
D05 I/O 8
D10 I/O
9
D04 I/O 10
D11 I/O
11
D03 I/O 12
D12 I/O
13
D02 I/O 14
D13 I/O
15
D01 I/O 16
D14 I/O
17
D00 I/O 18
D15 I/O
19
GND GND 20
NC KEY(no
pin)
21
DREQ DREQ 22
GND GND
23
/OW /OW 24
GND GND
25
/OR /OR 26
GND GND
27
IOCHRDY IORDY
28
H_SEL CSEL
29
/DACK /DACK 30
GND GND
31
INT IRQ 32
/IO16 /IOIS16
33
A01 I 34
/PDIAG I/O
35
A00 I 36
A02 I
37
/CS0 CS0 38
/CS1 I
39
/DASP (LED)
I/O
40
GND GND