ChipFind - документация

Электронный компонент: HFDOM44P-064Sx

Скачать:  PDF   ZIP
HANBit HFDOM44P-xxxSx
URL : www.hbe.co.kr 1 / 11 HANBit Electronics Co., Ltd.
REV 1.0 (August.2002)


1. PRODUCT OVERVIEW
GEN
ERAL DESCRIPTION
The HFDOM44P-xxxSx series 44Pin Flash Disk Module is a flash technology based with True IDE interface flash
memory card. It is constructed with flash disk controller chip and NAND-type (Samsung) flash memory device. The
HFDOM44P-xxxSx series operates in both 3.3-Volt and 5.0-Volt power supplies. It comes in capacity of 16, 32, 64, 128,
192, 256, 384 MB and up to 512 MB formatted 44Pin type .
By optimizing flash memory management, the life of this HFDOM44P-xxxSx series can be extended to its maximum
level. Because the ECC function is included, the correctness of data transfer between the HFDOM44P-xxxSx series and a
True IDE compatible interface device can be guaranteed.
The HFDOM44P-xxxSx series is fully compatible with applications such as CPU card / board, set top box, industry /
military PC / Notebook, security equipment, measuring instrument and embedded systems.
FEATURES
-
True IDE compatible host interface
-
Direct plug in for 2.5
IDE Connectors
-
44 pin 2.0mm IDE Connector
-
Very high performance, very low power consumption
-
Automatic error correction
-
Support 3 power save mode : stop/idle/active
-
Support for CIS implemented with 256 bytes of attribute memory
-
3.3V/5.0V operation voltage
-
Host data transfer rate : 20MB/s
-
Flash data transfer rate : 10MB/s
-
Host Interface bus width : 8/16 bit Access
-
Flash Interface bus width : 8 bit Access
-
Capacity : Min. 16MB ~ Max. 512MB
-
MTBF : 1,000,000 hours, minimum 30,000 insertions
-
Operating vibration : 15G peak to peak maximum
-
Operating shock : 1,000G maximum
PRODUCT SPECIFICATIONS
Capacities :
16, 32, 64, 128, 192, 256, 384 and up to 512 MB (formatted)
Power consumptions :
Read mode
30 mA (typ), 40 Ma (Max)
Write mode
30 mA (typ), 40 Ma (Max)
Stop mode
30 uA (typ)
Environment conditions :
Operating temperature
0
C to + 60
C
Storage temperature
- 25
C to + 85
C
Relative humidity
95%(Max)
Mechanical conditions :
Weight : Maximum 12.0g
Operating Voltage :
3.3V / 5.0V
10%

44Pin Flash Disk Module Min.16MB~Max.512MB, True IDE Interface
Mode, 3.3V/5.0V Operating Part No
. HFDOM44P-xxxSx
HANBit HFDOM44P-xxxSx
URL : www.hbe.co.kr 2 / 11 HANBit Electronics Co., Ltd.
REV 1.0 (August.2002)
ELECTRICAL SPECIFICATIONS
Table 1.1 Absolute Maximum Ratings
Symbol
Parameter
Ratings
Unit
V
DD
Supply voltage
- 0.3 to + 7.0
V
V
IN
Input voltage
- 0.3 to + 7.0
V
I
IN
DC input current
- 10
mA
T
STG
Storage temperature
- 20 to + 85
C
Table 1.2 Recommended Operating Conditions
Symbol
Parameter
Ratings
Unit
5V
4.75 to 5.25
V
V
DD
DC Supply voltage
3.3V
3.0 to 3.6
V
T
a
Storage temperature
- 20 to +70
C
Table 1.3 DC Characteristics
(Ta=0
C to 70
C, V
DD
=3.0 to 5.3V)
Symbol
Parameter
Min.
Typ.
Max.
Unit
I
DD
Operating Current
30
70
mA
I
ds
Stop Current
50
150
A
V
DD
High Level Output Voltage
2.4
V
V
DD
Low Level Output Voltage
0.4
V

CAPACITY SPECIFICATIONS
Table 1.4 Capacity Specifications
Part Number
Capacity (Unformatted)
Total Sector
Cylinders
Heads
Sectors
HFDOM44P-016Sx
15,990,784 bytes
31,232
61
16
32
HFDOM44P-032Sx
32,243,712 bytes
62,976
123
16
32
HFDOM44P-064Sx
65,536,000 bytes
128,000
250
16
32
HFDOM44P-128Sx
131,858,432 bytes
257,536
503
16
32
HFDOM44P-192Sx
196,608,000 bytes
384,000
750
16
32
HFDOM44P-256Sx
265,027,584 bytes
517,632
1011
16
32
HFDOM44P-384Sx
395,837,440 bytes
773,120
1510
16
32
HFDOM44P-512Sx
531,890,176 bytes
1,038,848
2029
16
32




HANBit HFDOM44P-xxxSx
URL : www.hbe.co.kr 3 / 11 HANBit Electronics Co., Ltd.
REV 1.0 (August.2002)
PHYSYCAL SPECIFICATIONS
2.7
0.1
Jumper 31.0
0.5mm
9.9
0.08mm
1.7
0.08mm
42.9
0.1mm
48.4
0.1mm
52.3
0.3mm
< View from connector side >
6.3
0.2mm
4.4
0.2mm
< View from Right side >
Figure 1.1 44 pin Type Flash Disk Module Dimensions

Jumper
Master Slave
1,2
Close
2,3
Close
2
1
3
2
1
HANBit HFDOM44P-xxxSx
URL : www.hbe.co.kr 4 / 11 HANBit Electronics Co., Ltd.
REV 1.0 (August.2002)
INSTALLTION GUIDE
1) Setting Method
Make sure your computer is turned off before you open the case.
Plug the Flash Disk Module carefully into the 44pin IDE slot on your computer.
Caution: Make sure to align pin1 on host adapter interface connector with pin 1 on your Flash Disk Module. Pin 1
is indicated by printed on the Flash Disk Module PCB.
The Flash Disk Module is not use power connector cable of the computer.
Caution: If you need to remove your Flash Disk Module, use both hands to pull it out carefully.
Check all cable connections and then replace your computer cover.
2) BIOS setting Method
Before you format or partition your new drive, you must configure your computer's BIOS so that the computer can
recognize your new drive.
Turn your computer on. As your computer start up, watch the screen for a message describing how to run the
system setup program on the screen (sometimes called BIOS or CMOS setup). This is usually done by pressing a
special key, such as Delete, Esc or F1 during startup. See your computer manual for details. Press the
appropriate key to run the system setup program.
If your BIOS provides automatic drive detection (an "AUTO" drive type), select this option. ( We
recommend to use Normal / CHS mode to partition your Flash Disk Module to get the maximum formatted
capacity.
)
This allows your computer to configure itself automatically for your new drive.
If your BIOS dose not provide
"
AUTO
"
drive detection, select "User-defined" drive setting and enter the
CHS values from the table. BIOS Settings (see specification) Capacity Cylinders Heads Sectors(unformatted)
Save the settings and exit the System Setup program. ( your computer will automatically reboot ) After you
configure your computer, you can use the standard DOS commands to partition and format your Flash Disk
Module, as described below.
3) Formatting Method
To partition your new Flash Disk Module with Microsoft DOS program :
Insert a bootable DOS diskette into your diskette drive and restart your computer.
Insert a DOS program diskette that contains the FDISK.EXE and FORMAT.COM
programs into your diskette drive. Use the same DOS version that is on your bootable diskette. At the A:\ >
prompt, type
"
FDISK
"
and press Enter.
Select
"
Create DOS partition or logical DOS drive
"
by pressing 1. Then press Enter.
Select
"
Create primary DOS partition
"
by pressing 1 again. Then press Enter.
Create your first drive partition. If you are creating a partition that will be used to boot your computer (drive C),
make sure that the partition is marked active.
Create an extended partition and additional logical drives as necessary, until all the space on your new hard drive
has been partitioned.
When the partitioning is complete, FDISK reboots your computer.
Caution: Make sure to use the correct drive letters so that you do not format a drive that already contains data.
At the A:\ > prompt, type
"
format c:/s
"
, where c is the letter of your first new partition, Repeat the format process
for all the new partitions you have created.
After you format your drive, it is ready to use.
HANBit HFDOM44P-xxxSx
URL : www.hbe.co.kr 5 / 11 HANBit Electronics Co., Ltd.
REV 1.0 (August.2002)
2. PIN INFORMATION
PIN ASSIGNMENTS AND PIN TYPE
Table 2.1 Pin Assignment and Pin type
Pin
Signal
Pin Type
Pin
Signal
Pin Type
1
/RESET
I
2
GND
Ground
3
D07
I/O
4
D08
I/O
5
D06
I/O
6
D09
I/O
7
D05
I/O
8
D10
I/O
9
D04
I/O
10
D11
I/O
11
D03
I/O
12
D12
I/O
13
D02
I/O
14
D13
I/O
15
D01
I/O
16
D14
I/O
17
D00
I/O
18
D15
I/O
19
GND
DC
20
Key Pin
--
21
Reserved
--
22
GND
Ground
23
/IOW
I
24
GND
Ground
25
/IOR
I
26
GND
Ground
27
IORDY
O
28
Reserved
--
29
Reserved
--
30
GND
Ground
31
IRQ
O
32
/IOIS16
O
33
A01
I
34
/PDIAG
I/O
35
A00
I
36
A02
I
37
/CS0
I
38
/CS1
I
39
/DASP(LED)
I/O
40
GND
Ground
41
VCC
Power
42
VCC
Power
43
GND
Ground
44
Reserved
--