ChipFind - документация

Электронный компонент: FH26-21S-0.3SHW

Скачать:  PDF   ZIP
1
0.3mm Contact Pitch, 1mm above the board, Flexible Printed Circuit ZIF Connectors
FH26 Series
2004.8
16.8mm
s
Features
1. Extremely light weight
The typical version, with all 51 contacts loaded, weights
only 0.1 grams.
2. Easy solderability on the PC board
The soldering leads are on 0.6 mm pitch, exiting on front
and back of the connector.
3. Conductive traces on the PCB can run under
the connector
No exposed contacts on the bottom of the connector.
4. Easy FPC insertion and reliable electrical
connection
Proven Flip LockR actuator allows easy insertion of FPC.
Tactile sensation when fully closed confirms complete
electrical and mechanical connection.
5. Accepts standard thickness FPC
0.2mm thick standard Flexible Printed Circuit board can
be used.
This is the only ultra-low profile ZIF connector allowing
the use of standard FPC.
6. Board placement with automatic equipment
Flat top surface and packaging on the tape-and-reel
allows use of vacuum nozzles.
Standard reel contains 5,000 connectors.
s
Applications
Mobile phones, PDA's, digital cameras, digital video
cameras, LCD connections, plasma displays (PDP), camera
modules and other compact devices requiring Flexible
Printed Circuit connections using high reliability ultra-small
profile connectors.
q
Space saving(51 pos. shown)
q
Can be mounted over conductive traces.
Metal fittings do no protrude
outside of the connector body
No exposed contacts on the bottom
of the connector
1.0mm
3.2mm
FPC
Actuator
Actuator
Actuator
FPC
q
Operation
(3) Close the actuator
(4) FPC connected
(3) Close the actuator
(4) FPC connected
(3) Close the actuator
(4) FPC connected
(3) Close the actuator
(4) FPC connected
(3) Close the actuator
(4) FPC connected
(3) Close the actuator
(4) FPC connected
(3) Close the actuator
(4) FPC connected
(3) Close the actuator
(4) FPC connected
(3) Close the actuator
(4) FPC connected
(3) Close the actuator
(4) FPC connected
(3) Close the actuator
(4) FPC connected
(3) Close the actuator
(4) FPC connected
(3) Close the actuator
(4) FPC connected
(3) Close the actuator
(4) FPC connected
(3) Close the actuator
(4) FPC connected
(3) Close the actuator
(4) FPC connected
(3) Close the actuator
(4) FPC connected
(1) Actuator open
(2) Insert FPC
(1) Actuator open
(2) Insert FPC
(1) Actuator open
(2) Insert FPC
(1) Actuator open
(2) Insert FPC
(1) Actuator open
(2) Insert FPC
(1) Actuator open
(2) Insert FPC
(1) Actuator open
(2) Insert FPC
(1) Actuator open
(2) Insert FPC
(1) Actuator open
(2) Insert FPC
(1) Actuator open
(2) Insert FPC
(1) Actuator open
(2) Insert FPC
(1) Actuator open
(2) Insert FPC
(1) Actuator open
(2) Insert FPC
(1) Actuator open
(2) Insert FPC
(1) Actuator open
(2) Insert FPC
(1) Actuator open
(2) Insert FPC
(1) Actuator open
(2) Insert FPC
q
w
e
r
2
Terminal type: SHW(SMT horizontal mounting)
Plating specifications
Blank: Tin-lead plated
(05) : Gold flash plated
---------------
---------------
Temperature: -55
/
+15
to +35
/
+85
/
+15
to +35
Time: 30
/
2 to 3
/
30
/
2 to 3 (Minutes)
5 cycles
Reflow: At the recommended temperature profile
Manual soldering: 350
+/-10
for 5
1
seconds
1 mA
10 cycles
50 M ohms min.
No flashover or insulation breakdown.
100 V DC
90 V AC /one minute
100 m ohms max.
*
Including FPC conductor resistance
Contact resistance: 100 m ohms max.
No damage, cracks, or parts dislocation.
No electrical discontinuity of 1
s or more.
Contact resistance: 100 m ohms max.
No damage, cracks, or parts dislocation.
Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 10 cycles, 3
directions.
No electrical discontinuity of 1
s. min.
Contact resistance: 100 m ohms max.
No damage, cracks, or parts dislocation.
Acceleration of 981 m/s
2
, 6 ms duration, sine half-wave waveform,
3 cycles in each of the 3 axis
Contact resistance: 100 m ohms max.
Insulation resistance: 50 M ohms min.
No affect on appearance or performance.
96 hours at temperature of 40
2
and humidity of 90% to 95%.
Contact resistance: 100 m ohms max.
Insulation resistance: 50 M ohms min.
No damage, cracks, or parts looseness.
No deformation of components affecting performance.
s
Materials
s
Ordering information
FH26 - 51S - 0.3 SHW (05)
1
3
4
2
5
Series name: FH26
No. of contacts: 13, 21, 23, 25, 27, 33, 35, 39,
41, 45, 51, 57, 71
Contact pitch: 0.3mm
1
2
3
4
5
Part
Contacts
Metal fitting
Insulator
Actuator
LCP
PA
Phosphor bronze
Color: Black
Color: Dark brown
Tin-lead plated (Note 3)
Tin plated (Lead free)
UL94V-0
Material
Finish
Remarks
s
Specifications
Rating
Current rating
0.2A DC
Voltage rating
30V AC
Operating temperature range -55
to +85
(Note 1)
Operating humidity range
Relative humidity 90%
max. (No condensation)
Storage temperature range -10
to +50
(Note 2)
Storage humidity range
Relative humidity 90% max.
Recommended FPC :
Thickness: = 0.2
0.03mm tin-lead plated (Note 3)
4. Durability
(Insertion/ withdrawal)
5. Vibration
6. Shock
7. Humidity
(Steady state)
8. Temperature cycle
9. Resistance to soldering heat
3. Contact resistance
1.
Insulation resistance
2.
Withstanding voltage
Item
Specification
Conditions
Note 1: Includes temperature rise caused by current flow.
Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range
and Humidity range covers non- conducting condition of installed connectors in storage, shipment or during transportation.
Note 3: When FPC is gold plated, the connector contacts must be also gold plated: Specify the (05) plating code.
3
B
0.6
0.3
C
0.6
(0.12)
(1.25)
(0.3)
3.2
0.5
1
1
0.1
0.1
1
0.3
A
(0.12)
Number of contacts indicator
(D: FPC insertion slot dimension)
E
3.2
s
Connector Dimensions
Notes
The coplanarity of each terminal lead within specified dimension is
0.1 mm.
Packaged on tape and reel only. Check packaging specification.
1
2
All dimensions: mm
Embossed tape reel packaging (5,000 pieces/reel).
Order by number of reels.
Part Number
FH26-13S-0.3SHW
FH26-21S-0.3SHW
FH26-23S-0.3SHW
FH26-25S-0.3SHW
FH26-27S-0.3SHW
FH26-33S-0.3SHW
FH26-35S-0.3SHW
FH26-39S-0.3SHW
FH26-41S-0.3SHW
FH26-45S-0.3SHW
FH26-51S-0.3SHW
FH26-57S-0.3SHW
FH26-71S-0.3SHW
CL580-0209-3
CL580-0207-8
CL580-0203-7
CL580-0208-0
CL580-0204-0
CL580-0210-2
CL580-0205-2
CL580-0201-1
CL580-0206-5
CL580-0211-5
CL580-0200-9
CL580-0212-8
CL580-0202-4
13
21
23
25
27
33
35
39
41
45
51
57
71
5.4
7.8
8.4
9.0
9.6
11.4
12.0
13.2
13.8
15.0
16.8
18.6
22.8
3.0
5.4
6.0
6.6
7.2
9.0
9.6
10.8
11.4
12.6
14.4
16.2
20.4
3.6
6.0
6.6
7.2
7.8
9.6
10.2
11.4
12.0
13.2
15.0
16.8
21.0
4.23
6.63
7.23
7.83
8.43
10.23
10.83
12.03
12.63
13.83
15.63
17.43
21.63
4.9
7.3
7.9
8.5
9.1
10.9
11.5
12.7
13.3
14.5
16.3
18.1
22.3
CL No.
Number of Contacts
A
B
C
D
E
4
(0.55:Metal mask)
(0.65:Metal mask)
(0.23:Metal mask)
(0.2)
(0.45)
2.15
0.05
0.8
0.05
0.2
0.05
(0.23:Metal mask)
0.95
0.05
0.6
0.05
0.5
0.05
0.4
0.05
(0.3:Metal mask)
(0.7:Metal mask)
0.6
0.05
0.3
0.05
(3.6)
0.65
0.05
0.3
0.03
Outline of
the connector
B
0.05
C
0.05
0.3
0.05
0.6
0.07
0.6
0.07
0.5min.
(0.2)
(0.07)
0.6
0.02
B
0.03
0.3
0.07
H
C
0.03
3.5 MIN.(Stiffener)
2.5
0.3
F
0.05
0.3
0.07
R0.2 MAX
0.3
0.1
0.3
0.02
0.2
0.03
1
0.1
1.1
0.1
2.1
0.1
2.25
0.1
0.3
+0.04
-0.03
0.3
+0.04
-0.03
0.1
0.02
(2.5)
(0.5)
(0.15)
(0.2)
1
10.1
1.10.1
00.03
(Lead plated 0.1 MAX)
B
Recommended PCB mounting pattern and metal mask dimensions
B
Recommended FPC Dimensions
Detail H
Overlap between covering film layer and stiffener.
1
All dimensions: mm
Part Number
FH26-13S-0.3SHW
FH26-21S-0.3SHW
FH26-23S-0.3SHW
FH26-25S-0.3SHW
FH26-27S-0.3SHW
FH26-33S-0.3SHW
FH26-35S-0.3SHW
FH26-39S-0.3SHW
FH26-41S-0.3SHW
FH26-45S-0.3SHW
FH26-51S-0.3SHW
FH26-57S-0.3SHW
FH26-71S-0.3SHW
CL580-0209-3
CL580-0207-8
CL580-0203-7
CL580-0208-0
CL580-0204-0
CL580-0210-2
CL580-0205-2
CL580-0201-1
CL580-0206-5
CL580-0211-5
CL580-0200-9
CL580-0212-8
CL580-0202-4
13
21
23
25
27
33
35
39
41
45
51
57
71
3.0
5.4
6.0
6.6
7.2
9.0
9.6
10.8
11.4
12.6
14.4
16.2
20.4
3.6
6.0
6.6
7.2
7.8
9.6
10.2
11.4
12.0
13.2
15.0
16.8
21.0
4.2
6.6
7.2
7.8
8.4
10.2
10.8
12.0
12.6
13.8
15.6
17.4
21.6
CL No.
Number of Contacts
B
C
F
5
B
Packaging Specification
q
Embossed Carrier Tape Dimensions (Tape width of 24mm max.)
q
Embossed Carrier Tape Dimensions (Tape width of 32mm min.)
Unreeling direction
Flat surface, for placement with automatic equipment
(1.6)
(0.3)
40.1
20.15
80.1
1.750.1
J0.1
G0.3
(K)
(1.25)
(4.55)
(3.05)
1.5
+0.1 0
Flat surface, for placement with automatic equipment
Unreeling direction
(1.6)
(0.3)
1.750.1
J0.1
G0.3
H0.1
(K)
(1.25)
(4.55)
(3.05)
1.5
+0.1 0
1.5
+0.1
0
1.7
+0.15 0
All dimensions: mm
Part Number
FH26-13S-0.3SHW
FH26-21S-0.3SHW
FH26-23S-0.3SHW
FH26-25S-0.3SHW
FH26-27S-0.3SHW
FH26-33S-0.3SHW
FH26-35S-0.3SHW
FH26-39S-0.3SHW
FH26-41S-0.3SHW
FH26-45S-0.3SHW
FH26-51S-0.3SHW
CL580-0209-3
CL580-0207-8
CL580-0203-7
CL580-0208-0
CL580-0204-0
CL580-0210-2
CL580-0205-2
CL580-0201-1
CL580-0206-5
CL580-0211-5
CL580-0200-9
13
21
23
25
27
33
35
39
41
45
51
16
16
16
16
16
24
24
24
24
24
24
7.5
7.5
7.5
7.5
7.5
11.5
11.5
11.5
11.5
11.5
11.5
5.6
8.0
8.6
9.2
9.8
11.6
12.2
13.4
14.0
15.2
17.0
16.5
16.5
16.5
16.5
16.5
24.5
24.5
24.5
24.5
24.5
24.5
CL No.
Number of Contacts
G
J
K
L
5, 000 pieces per reel.
All dimensions: mm
Part Number
FH26-57S-0.3SHW
FH26-71S-0.3SHW
CL580-0212-8
CL580-0202-4
57
71
32
44
28.4
40.4
14.2
20.2
18.8
23.0
32.5
44.5
CL No.
Number of Contacts
G
H
J
K
L
6
(L)
(2)
130.
5
(380)
(80)
Lead section (400mm min.)
End section
Mounting section
Connectors
Top cover tape
Embossed carrier tape
Blank section
Blank section
(10 pockets min.)
(10 pockets min.)
Unreeling direction
q
Reel Dimensions
7
B
Recommended Temperature Profile
HRS test conditions
Solder method
:Reflow, IR/hot air
(Nihon Den-netsu Co., Ltd.'s
Part Number: SENSBY NR-2)
Environment:
:Room air
Solder composition:
:Paste, 63%Sn/37%Pb
(Senju Metal Industry, Co., Ltd.'s
Part Number: OZ63-201C-50-9)
Test board
:Glass epoxy 25mm50mm0.8mm thick
Land dimensions
:0.3mm0.65mm,0.3mm0.8mm
Metal mask
:0.230.550.1mm thick,
0.230.650.1mm thick
The temperature profiles are based on the above conditions.
In individual applications the actual temperature may
vary,depending on solder paste type, volume/thickness and
board size/thickness. Consult your solder paste and
equipment manufacturer for specific recommendations.
HRS test conditions
Solder method
:Reflow, IR/hot air
(Nihon Den-netsu Co., Ltd.'s
Part Number: SENSBY NR-NR-2)
Environment
:Room air
Solder composition
:Paste, 96.5%Sn/3.0%Ag/0.5%Cu
(Senju Metal Industry, Co., Ltd.'s
Part Number: M705-221CM5-42-10.5)
Test board
:Glass epoxy 25mm50mm0.8mm thick
Land dimensions
:0.3mm0.65mm, 0.3mm0.8mm
Metal mask
:0.230.550.1mm thick,
0.230.650.1mm thick
The temperature profiles are based on the above conditions.
In individual applications the actual temperature may vary,
depending on solder paste type, volume/thickness and board
size/thickness. Consult your solder paste and equipment
manufacturer for specific recommendations.
Start
Time (Seconds)
60
25
60sec.
20 sec. to
30 sec.
30sec.
60 sec. to 90 sec.
Preheating
Soldering
0
50
100
150
150
160
240
200
5 sec. max.
200
250
120
Temperature
q
Using Typical Solder Paste
MAX 250
Start
Time (Seconds)
60
25
60sec.
60sec.
90 sec. to 120 sec.
Preheating
Soldering
0
50
100
150
150
200
230
200
250
120
Temperature
q
Using Lead-free Solder Paste
8
B
Recommended FPC Construction
1. Using Single-sided FPC
Material Name
Covering film layer.
Cover adhesive
Surface treatment
Copper foil
Base adhesive
Base film
Reinforcement material adhesive
Stiffener
Polyamide
1 mil thick.
Tin-lead plated
Cu
1/2oz
Thermosetting adhesive
Polyamide
1 mil thick
Thermosetting adhesive
Polyamide
3 mil thick
Total
25
25
5
35
25
25
40
75
205
Material
Thickness (m)
2. Using Double-sided FPC
Material Name
Back side
Covering layer film
Cover adhesive
Surface treatment
Through-hole copper
Copper foil
Base adhesive
Base film
Base adhesive
Copper foil
Cover adhesive
Covering layer film
Reinforcement material adhesive
Stiffener
Polyamide
1 mil thick
Tin-lead plated
Cu
Cu
1/2oz
Thermosetting adhesive
Polyamide
1 mil thick
Thermosetting adhesive
Cu
1/2oz
Thermosetting adhesive
Polyamide
1 mil thick
Thermosetting adhesive
Polyamide
1 mil thick
Total
25
25
5
15
18
18
25
18
18
25
25
25
25
199
Material
Thickness (m)
q
To prevent release of the FPC due to it's bending, use of double sided FPC with copper foil on the back side is NOT RECOMMENDED.
q
Contact FPC manufacturer for specific details.
Back side
Connecting side
Connecting side
9
B
Operation and Precautions
Operation
1.FPC insertion procedure. Connector installed on the board.
Lift up the actuator. Use thumb or index finger.
1
2.FPC removal
Lift up the actuator. Carefully withdraw the
FPC.
1
Fully insert the FPC in the connector parallel to
mounting surface, with the exposed conductive
traces facing down.
2
Rotate down the actuator until firmly closed. It is
critical that the inserted FPC is not moved and
remains fully inserted.
3
FPC conductor
surface (Bottom side)
10
Precautions
Exercise care when handling connectors. Follow recommendations given below.
PC board flexing
S
PC board connector mounting area
The connectors are straight within 0.1 mm max.
Make sure that the PC board connector mounting area flatness can accept the connector terminals without
causing any failure of the solder joints.
S
Handling before mounting on PCB
Insertion of the FPC or operation of the actuator prior to mounting on the PCB is NOT RECOMMENDED.
S
PC Board handling
Exercise caution when handling boards with the connectors installed. Do not apply any forces affecting
soldered joints.
Precautions When Inserting or Coupling FPC
Pay attention to the following points when inserting FPC.
S
Actuator operation
Do not apply excessive force when opening the actuator prior to FPC insertion. When opening make sure
that the force is applied only to the actuator itself, avoiding touching of the contacts.
Connector
PCB
Damage
Assure free rotation of
the actuator
1
Axis of rotation
2
Axis of rotation
Damage to the contacts
Actuator
11
Precautions
The actuator will rotate 135 degrees
maximum. Do not apply force to rotate
further.
3
When operating the actuator, do so at the
center portion.
4
135
As illustrated, do not attempt removal or re-
positioning of the actuator.
5
S
FPC Insertion
q
The FPC should be aligned parallel with the board surface and perpendicular with the connector (as
shown), then completely inserted.
To assure correct electrical and mechanical connection do not insert FPC at angle. It must be fully inserted.
Make sure that the FPC is NOT MOVED during the closing of the actuator.
Perpendicular with
the connector
12
Precautions
S
Verification of the fully closed actuator.
The actuator should be fully closed (as illustrated) and the FPC held firmly in the connector.
Do not press against the actuator when is fully closed. Max force applied to the fully closed actuator should
not exceed 1 N.
*
To avert insertion of the FPC on an angle, consideration should be given to securing FPC insertion space
at the time of board layout. Insertion will be difficult when the FPC is too short.
*Contact the FPC manufacturer for information about the bending specifications.
Routing the FPC (FPC fully inserted/ actuator closed)
S
FPC Load
Do not apply force in excess of 0.05N/pin max. in the upward direction (as illustrated). Do not bend the
FPC too close to the actuator.
Load: 0.05N/pin max.
S
FPC Insertion
w
Do not insert the FPC at any angle from above.
As illustrated, angle insertion may cause electrical discontinuity when the FPC is deflected in use.
13
Precautions
Removing the FPC
Rotate the actuator to the open position (maximum open angle of 135). Carefully withdraw the FPC.
Other Precautions
S
Hand Soldering Precautions
When hand soldering:
Do not perform reflow or hand soldering with the FPC inserted in the connector.
Do not apply excessive heat or touch the soldering iron anywhere other than the connector leads.
Do not use excessive amount of solder or flux compounds.
Operation of the actuator and contacts may be affected by excessive amounts of solder or flux
compounds.
135
1
2
3
14
NOTES :
15
NOTES :
16
The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of improvements.
The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of improvements.
The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of improvements.
USA:
HIROSE ELECTRIC U.S.A., INC.
2688 Westhills Court, Simi Valley, CA 93065-6235
Phone : 1 805 522 7958
Fax : 1 805 522 3217
http://www.hiroseusa.com
UNITED KINGDOM:
HIROSE ELECTRIC UK LTD.
Crownhill Business Centre 22 Vincent Avenue
Crownhill, Milton Keynes MK8 OAB
Phone : 44 1908 305400
Fax : 44 1908 305401
http://www.hirose.co.uk
HONG KONG:
HIROSE ELECTRIC CO., LTD.
Unit 506, Energy Plaza. 92 Granville Road, Tsim Sha
Tsui East, Kowloon
Phone : 852 2803 5338
Fax : 852 2591 6560
GERMANY:
HIROSE ELECTRIC GmbH
Zeppelinstrasse 42 D-73760 Ostfildern Kemnat
Phone : 49 711 4560021
Fax : 49 711 4560729
http://www.hirose.de
KOREA:
HIROSE KOREA CO., LTD.
(#2NA311,Shihwa Industrial Complex),
1261-10, Jeoungwhang-Dong, Shihung-City, Kyunggi-Do
Phone : 82 31 496 7000,7124
Fax : 82 31 496 7100
http://www.hirose.co.kr
TAIWAN:
HIROSE ELECTRIC TAIWAN CO., LTD.
No.28 Lane 247 Sec. 2 Yen Ping N,Rd.Taipei
Phone : 886 2 2557 7351,7352
Fax : 886 2 2552 9851
THE NETHERLANDS:
HIROSE ELECTRIC EUROPE B.V.
Beechavenue 46.1119PV
Schiphol-Rijk
Phone : 31 20 6557460
Fax : 31 20 6557469
http://www.hiroseeurope.com
CHINA:
HIROSE ELECTRIC TRADING(SHANGHAI) CO., LTD.
3705,Bund Center,222 Yan An Road(E),Shanghai 20002
Phone : 86 21 6335 2538
Fax : 86 21 6335 0767
SINGAPORE:
HIROSE ELECTRIC CO., LTD.
10 Anson Road
#34-13 International Plaza 079903
Phone : 65 6324 6113
Fax : 65 6324 6123
5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN
PHONE: 81-3-3491-9741, FAX: 81-3-3493-2933
http://www.hirose.com
http://www.hirose-connectors.com
NOTES :